虚实结合的可穿戴产品适合性检验研究

目的 为了更科学地研究和检验可穿戴产品的适合性,提出一种适合性检验方法,能够精确保留现实环境中的产品佩戴关系,并能将现实与虚拟的适合性检验研究相结合,得到合理的适合性检验结果.方法 以虚拟现实眼镜的适合性检验为例,通过高精度的三维测量技术将现实环境中的人、产品以及人—产品佩戴关系转化为三维虚拟信息,并以人—产品佩戴三维模型为参考基准对齐人和产品的虚拟模型,得到保留现实佩戴关系的人—产品佩戴模型组,再应用偏差分析法得出人—机佩戴区域的可视化适合性结果和统计数据,结合主观评价方法进一步分析产品的适合性.结论 虚实结合的产品适合性检验方法可在虚拟环境中高精度地保留现实环境中的人—产品佩戴关系,并能得到可视化的适合性检验结果,为检验和指导产品的适合性提供依据.     

Turbulent boundary layer control with a spanwise array of DBD plasma actuators

The turbulent boundary layer control on NACA 0012 airfoil with Mach number ranging from 0.3 to 0.5 by a spanwise array of dielectric barrier discharge(DBD)plasma actuators by hot-film sensor technology is investigated.Due to temperature change mainly caused through heat produced along with plasma will lead to measurement error of shear stress measured by hot-film sensor,the correction method that takes account of the change measured by another sensor is used and works well.In order to achieve the value of shear stress change,we combine computational fluid dynamics computation with experiment to calibrate the hot-film sensor.To test the stability of the hot-film sensor,seven repeated measurements of shear stress at Ma = 0.3 are conducted and show that confidence interval of hot-film sensor measurement is from-0.18 to 0.18 Pa and the root mean square is 0.11 Pa giving a relative error 0.5％over all Mach numbers in this experiment.The research on the turbulent boundary layer control with DBD plasma actuators demonstrates that the control makes shear stress increase by about 6％over the three Mach numbers,which is thought to be reliable through comparing it with the relative error 0.5％,and the value is hardly affected by burst frequency and excitation voltage.     

Hydrogen sulfide gas detection by Au-decorated ZnO nanotube: a computational study and comparison to experimental observations

Based on the experimental reports, Au-decoration on the ZnO nanostructures dramatically increases the electronic sensitivity to H₂S gas. In the current study, we computationally scrutinized the mechanism of Au-decoration on a ZnO nanotube (ZON) and the influence on its sensing behavior toward H₂S gas. The intrinsic ZON weakly interacted with the H₂S gas with an adsorption energy of ?11.2 kcal/mol. The interaction showed no effect on the HOMO–LUMO gap and conductivity of ZON. The predicted response of intrinsic ZON toward H₂S gas is 6.3, which increases to 78.1 by the Au-decoration at 298 K. The corresponding experimental values are about 5.0 and 80.0, indicating excellent agreement with our findings. We showed that the Au atom catalyzes the reaction 3O₂?+?2H₂S?→?2SO₂?+?2H₂O. Our calculated energy barrier (at 298 K) is about 12.3 kcal/mol for this reaction. The gap and electrical conductance Au-ZON largely changed by this reaction are attributed to the electron donation and back-donation processes. The obtained recovery time is about 1.35 ms for desorption of generated gases from the surface of the Au-ZON sensor.     

Potential influence of microorganisms on the corrosion of carbon steel in the French high- and intermediate-level long-lived radioactive waste disposal context

In the context of the high-level radioactive waste disposal CIGEO, the corrosion rate due to microbially influenced corrosion (MIC) has to be evaluated. In France, it is envisaged to dispose of high- and intermediate-level long-lived radioactive waste at a depth of 500 m in a deep geological disposal, drilled in the Callovo-Oxfordian claystone (Cox) formation. To do so, a carbon steel casing will be inserted inside disposal cells, which are horizontal tunnels drilled in the Cox. A specific cement grout will be injected between the carbon steel casing and the claystone. A study was conducted to evaluate the possibility of MIC on carbon steel in the foreseeable high radioactive waste disposal. The corrosiveness of various environments was investigated at 50°C and 80°C with or without microorganisms enriched from samples of Andra's underground research laboratory. The monitoring of corrosion during the experiments was ensured using gravimetric method and real-time corrosion monitoring using sensors based on the measurements of the electrical resistance. The corrosion data were completed with microbiological analyses including cultural and molecular characterizations.     

基于PMU的电力系统监控体系结构优化设计

文中提出了一种利用有限数量的相量测量单元(PMU)和相量数据集中器(PDC)设计最优监控结构的方法。通过在大量的设定值场景下,使电力系统可观测性曲线的期望值最大化,同时使通信基础设施成本最小化,最终确定PMU和PDC的最佳位置。提出了一种非线性动态扩展卡尔曼滤波(EFK)状态观测器。这种状态观测器可以将暂态行为转换为由代数微分方程描述的广域电力系统,而无需非线性反演技术。最后以IEEE-5电力系统为例,说明了该方法的有效性。     

Effect of heat treatment on structural,morphological, dielectric and magnetic properties of Mg–Zn ferrite nanoparticles

Green combustion was used to prepare a ferrite composition of Mg_0.4Zn_0.6Fe₂O₄ using a blend of fresh lemon juice as a natural fuel-reductant. Effect of heat treatment on phase, morphological, dielectric, and humidity sensor properties is discussed. The formation of a cubic spinel ferrite has been established by XRD-diffraction and vibrational spectroscopic studies. The experimental lattice parameter ranges from 8.3721 to 8.3631 Å. The broadening of octahedral band (υ₂) in the vibrational spectra is an identification for the existence of ferrite nanoparticles in various sizes. The typical crystallite size ranges from 10.2 to 36.9 nm. Using micrographs obtained from field-effect scanning electron microscopy (FESEM), researchers observed a spherical-shaped microstructure with agglomerated nanoparticles. Dielectric investigations have shown that the current ferrite composition has typical dielectric dispersion. The highest reported value for saturation magnetization (M_s) in the present study is 33 emu/g. Magnetic behaviour is primarily influenced by magnetocrystalline anisotropy, cation distribution, and crystallite size. The existence of void spaces in the sintered samples, as well as their porous nature, rendered them suitable for humidity sensor applications. Sintered samples have good sensing capability at 900 °C. The current findings are integrated in terms of cation distribution and magnetocrystalline anisotropy, assuming fine size effects of ferrite nanoparticles.     

高光谱成像用高帧频CMOS图像传感器北大核心

针对高帧频、全局曝光和光谱平坦等成像应用需求,设计了一款高光谱成像用CMOS图像传感器。其光敏元采用PN型光电二极管,读出电路采用5T像素结构。采用列读出电路以及高速多通道模拟信号并行读出的设计方案来获得低像素固定图像噪声(FPN)和非均匀性抑制。芯片采用ASMC 0.35μm三层金属两层多晶硅标准CMOS工艺流片,为了抑制光电二极管的光谱干涉效应,后续进行了光谱平坦化VAE特殊工艺,并对器件的光电性能进行了测试评估。电路测试结果符合理论设计预期,成像效果良好,像素具备积分可调和全局快门功能,最终实现的像素规模为512×256,像元尺寸为30μm×30μm,最大满阱电子为400 ke^(-),FPN小于0.2%,动态范围为72 dB,帧频为450 f/s,相邻10 nm波段范围内量子效率相差小于10%,可满足高光谱成像系统对CMOS成像器件的要求。     

电容式力感知牙周探针设计建模与实验研究

针对当前牙周探针在探诊力控制方面的不足,提出一种基于悬臂梁挠曲效应的差动电容式力感知牙周探针解决方案,设计了探针验证结构,建立了探诊力作用下具有不规则形状的探针工作尖的挠曲模型,导出了探诊力和差动电容之间的求解方程,并通过仿真和实验对模型与方程进行了验证。结果表明,所建立的探针工作尖挠曲模型与静应力仿真结果的最大相对误差不超过±4.5%,所设计的力感知牙周探针多次重复探诊力检测实验的标准差小于均值的0.1%,所导出的求解方程的计算值与实验数据之间趋向一致,以探诊力为拟合权重进行修正后全量程的平均偏差为2.49%,具备进一步产品开发的可行性。     

A Terahertz Video Camera Patch Sheet with an Adjustable Design based on Self-Aligned, 2D,Suspended Sensor Array Patterning

Terahertz (THz) imaging is expected to become powerful tools for non-destructive inspections. To ensure the practical use of THz non-destructive monitoring, versatile THz imagers with adjustable designs that can eliminate the complexities and the bulkiness of the device are urgently required. Herein, a self-aligned filtration process for a 2D, free-standing carbon nanotube film array and its application to a THz video camera patch are reported. The presented techniques enable a) to freely design the camera size, sensor array pattern, and suspended shape according to its applications, b) to cut the camera patch into desired shapes, and c) to attach them to the objects that are intended to be measured. Real-time, non-destructive monitoring of various infrastructures is demonstrated. These results indicate that it can function regardless of restrictions, such as the shapes and locations of the measurement samples, thus providing a strong possibility for use in future non-destructive sensor networks.     

小型无线场强探测传感器研究

近年来,微波加热因其高效性和清洁无污染等优点广泛应用于各个领域。然而,微波加热的不均匀性限制了微波作为高效加热能源的应用。通过测量和分析加热腔中的电场分布情况可以帮助设计人员改进微波加热腔体设计,提高微波加热的均匀性。现有的场强测量设备均为有线设备,应用场景极为有限。因此,本文提出了一种由探头、接收机和上位机三部分组成的无线场强探测传感器。介绍了无线场强探测传感器的结构和原理,采用横电磁波小室进行校准。通过一系列测量实验表明实测值与标准场强仪测量值一致性较好,可满足工程测量需求。