Effects of SO2 on selective catalytic reduction of NO with NH3 over a TiO2 photocatalyst

The effect of SO₂ gas was investigated on the activity of the photo-assisted selective catalytic reduction of nitrogen monoxide (NO) with ammonia (NH₃) over a TiO₂ photocatalyst in the presence of excess oxygen (photo-SCR). The introduction of SO₂ (300 ppm) greatly decreased the activity of the photo-SCR at 373 K. The increment of the reaction temperature enhanced the resistance to SO₂ gas, and at 553 K the conversion of NO was stable for at least 300 min of the reaction. X-ray diffraction, FTIR spectroscopy, thermogravimetry and differential thermal analysis, x-ray photoelectron spectroscopy (XPS), elemental analysis and N₂ adsorption measurement revealed that the ammonium sulfate species were generated after the reaction. There was a strong negative correlation between the deposition amount of the ammonium sulfate species and the specific surface area. Based on the above relationship, we concluded that the deposition of the ammonium sulfate species decreased the specific surface area by plugging the pore structure of the catalyst, and the decrease of the specific surface area resulted in the deactivation of the catalyst.     

Detection of Multiple Blockages in Parallelized Microreactors

In a plant consisting of parallelized microreactors (MRs), the product quality is lowered because of a lack of flow uniformity among them when blockage occurs. It is not practical to install sensors in every MR from the viewpoint of cost when detecting the blocked MRs. In the previous study, the multiple blockage detection (MBD) method using a small number of sensors was proposed, but its performance became low when the number of sensors decreased. Here, the conventional algorithm for MBD is improved by considering the process behavior on blockage occurrence, and the effectiveness of the improved algorithm is demonstrated through a numerical case study. The effects of flow distributor types and sensor types on the MBD performance are numerically investigated.     

Serum vanadium levels in chronic hemodialysis patients

Serum vanadium, aluminum, silicon and beta 2-microglobulin levels as well as the red cell count, hemoglobin and systolic blood pressure were simultaneously measured in 80 chronic hemodialysis patients. The serum vanadium level was positively correlated with the serum levels of aluminum, silicon and beta 2-microglobulin as well as the systolic blood pressure, and was inversely correlated with the red cell count and hemoglobin. The mean serum vanadium level was 18.4 +/- 7.6 ng/ml before hemodialysis and decreased to 13.0 +/- 5.30 ng/ml at the completion of dialysis. The dialysate vanadium level increased from 0.4 +/- 0.2 (inflow) to 1.0 +/- 0.4 ng/ml (outflow). It was concluded that vanadium was transferred from blood to dialysate when purified water was used in the preparation of the dialysate.     

Circulating platelet-derived endothelial cell growth factor increases in hepatocellular carcinoma patients

BACKGROUND: Platelet-derived endothelial cell growth factor (PD-ECGF) is an angiogenic factor that is expressed in various cancer tissues. Little is known regarding plasma PD-ECGF levels in patients with chronic liver disease such as chronic hepatitis (CH), cirrhosis, and hepatocellular carcinoma (HCC) with cirrhosis. The expression of PD-ECGF in HCC tissues also remains to be clarified. METHODS: Plasma PD-ECGF levels in patients with chronic liver disease were determined with an enzyme-linked immunoadsorbent assay system using the mouse monoclonal antibodies specific to PD-ECGF. These were cross-sectionally compared among groups of normal persons, CH, cirrhosis, and HCC patients. The HCC patients were classified into two groups based on TNM stage: early and advanced stage disease groups. PD-ECGF expressions in HCC tissues were immunohistologically examined. RESULTS: The plasma PD-ECGF levels from the normal individuals and those with CH, cirrhosis, and HCC specimens were 4.2+/-0.5, 4.3+/-0.6, 4.6+/-1.1, and 6.0 +/-2.5 U/mL, respectively. The plasma PD-ECGF concentration was highest in HCC (P < 0.05). No significant difference was found among the normal subjects, CH, and cirrhosis specimens. Plasma PD-ECGF concentrations were significantly higher in the advanced stage disease HCC group compared with the early stage disease group (6.75+/-2.62 U/mL vs. 4.19+/-0.34 U/mL) (P < 0.05). Immunohistochemical expression of PD-ECGF in HCC cells increased significantly compared with normal liver cells (P < 0.05). CONCLUSIONS: Circulating PD-ECGF plasma level might be a new tumor marker for progression in patients with HCC. Immunohistological findings correspond to elevation of the plasma PD-ECGF in HCC patients. It is possible that increased production of PD-ECGF in HCC cells causes abundant neovascularization.     

Superplastic behaviour of Ti-48at.%Al two-phase titanium aluminide compacts made from mechanically alloyed powder

An HIP compact of MA-processed powder having a nominal composition of Ti-48at.% Al was produced. The compact consisted of a large amount of TiAl(λ) and a small amount of Ti₃Al (₂), in a completely ultra-fine equiaxed grain structure. This two-phase compact showed typical superplastic deformation behaviour. A maximum elongation of 550% was obtained. A strain exponent, n = 2, and grain size exponent, p = 2, were determined from the results of a strain-rate-change test and a creep test at constant initial stress using samples having various grain sizes, respectively. The activation energy for creep, Q_c at constant stress was calculated to be 350 kJ/mole. It is concluded that the superplastic deformation mechanism of the material under study is grain boundary sliding controlled by lattice diffusion in the TiAl phase.     

An investigation of induced voltages to an underground gas pipeline from an overhead transmission line

This paper investigates induced voltage characteristics from an overhead transmission line by applying a method of modeling of induced voltages proposed by the authors. EMTP simulation results obtained by the modeling method agree with analytical results obtained from a well‐known formula. The induced voltages are significantly dependent on the configuration of the overhead line. A horizontal line induces the largest voltage in a gas pipeline, and the voltage induced by a vertical twin‐circuit line is about 20% smaller than that induced by a vertical single‐circuit line. The method is applied to a real pipeline system and the simulation results show reasonable agreement with field test results. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 43–51, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20465     

Periacinar collagenization in patients with chronic alcoholism

To examine the development of pancreatic fibrosis in alcoholics, the fibrosis types grouped according to Martin's classification were examined by immunohistochemistry using an antibody against alpha-smooth muscle actin (alpha-SMA). The initial stage of periacinar collagenization was also investigated by electron microscopy. The total incidence of pancreatic fibrosis at autopsy of the 29 alcoholics was significantly higher than that of the 40 non-alcoholics. Intralobular sclerosis was observed to be the most frequent type of fibrosis regardless of alcohol intake. No differences in the enhancement of alpha-SMA expression in each type of fibrosis were found between the alcoholics and non-alcoholics. Electron microscopically, myofibroblasts were found around acini in the early stage of periacinar collagenization, and were accompanied by numerous fine filaments (8-15 nm in diameter). The various changes in zymogen granules (ZG), lysosomes and lipid droplets were augmented in the acinar cells of alcoholics. Medium-density materials were also found in dilated rough endoplasmic reticulum (RER). The contents of ZG and RER occasionally leaked out. In conclusion, pancreatic fibrosis was increased in alcoholics; myofibroblasts may play an important role in the initial stage of periacinar collagenization; and the intracellular transport blockage of protein as represented by abnormalities of ZG, ER and lysosomes may contribute to the development of periacinar collagenization.     

GBLT-VG for High User Densities by User Group Behavior and Hot Point in MMO Virtual Environment

Massively Multiplayer Online (MMO) games have large-scale virtual environments. Here, we propose a load distribution technique called the Group Based Load-distribution Technique with Virtual Group (GBLT-VG) that utilizes Peer-to-Peer (P2P) communication to maintain scalability under high user density conditions in MMO virtual environments. A common problem of P2P virtual environments is that user group behavior frequently generates high user density conditions. Existing techniques to manage the virtual environment cannot maintain performance in such high user density situations. The proposed technique, GBLT-VG, reduces area management loads of manager peers by introducing a new manager who manages a user neighbor group. GBLT-VG forms the user neighbor group efficiently by using party function under high user density conditions caused by users?? cooperative behaviors. In addition, GBLT-VG reduce the management load by using a virtual group when a number of parties is small, thereby decreasing the existing managers?? loads dynamically. This paper also presents simulation results demonstrating how GBLT-VG can reduce the average number of users managed by the server.     

Laser Dressing of Metal Bonded Diamond Wheel

In this study, a laser beam is used as a non-contact thermal dressing tool for a bronze bonded diamond wheel. The pulsed-Nd:YAG laser beam is irradiated on the wheel surface and the bond material partially removed by laser irradiation only. In order to efficiently remove the bond material, it is necessary to direct an air jet on the spot irradiated by the laser so as to blow away the molten binder before it solidifies again. Less damage of diamond particles such as micro-cracks or graphitization occurs. In grinding with a laser-dressed wheel, the grinding forces are almost the same as those for a conventionally dressed wheel. Consequently, effective laser dressing can be expected with the associated dressing conditions.