Control strategy for a distributed DC power system with renewable energy

This paper deals with a DC-micro-grid with renewable energy. The proposed method is composed of a gearless wind power generation system, a battery, and DC loads in a DC distribution system. The battery helps to avoid the DC over-voltages by absorbing the power of the permanent magnet synchronous generator (PMSG) during line-fault. In addition, the control schemes presented in this paper including the maximum power point tracking (MPPT) control and a pitch angle control for the gearless wind turbine generator. By means of the proposed method, high-reliable power can be supplied to the DC distribution system during the line-fault and stable power supply from the PMSG can be achieved after line-fault clearing. The effectiveness of the proposed method is examined in a MATLAB/Simulink^® environment.     

Output power leveling of wind turbine generators using pitch angle control for all operating regions in wind farm

Effective utilization of renewable energies such as wind energy instead of fossil fuels is desirable. Wind energy is not constant and windmill output is proportional to the cube of the wind speed, which causes the generated power of wind turbine generators (WTGs) to fluctuate. In order to reduce the output power fluctuation of wind farms, this paper presents an output power leveling control strategy for a wind farm based on both the average wind farm output power and the standard deviation of the wind farm output power, a cooperative control strategy for WTGs, and pitch angle control using a generalized predictive controller (GPC) in all WTG operating regions. Simulation results using an actual detailed model for wind farm systems show the effectiveness of the proposed method. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 158(4): 31– 41, 2007; Published online in Wiley InterScience ( www.interscience. wiley.com ). DOI 10.1002/eej.20448     

Effect of Support Materials on the Selective Methanation of CO over Ru Catalysts

Selective methanation of CO in the reformate gas (CO/CO₂/H₂/H₂O = 0.175/17.9/70.9/11.1) proceeded over Ru catalysts supported on metal oxides and zeolites. CO was selectively methanated at wide temperature ranges (200–275 °C) over Ru/γ-Al₂O₃, Ru/TiO₂ Ru/H-Y and Ru/H-beta catalysts. Higher Ru contents in Ru/γ-Al₂O₃ improved the selective CO methanation rate.     

A dual doubly curved reflector antenna having good circular polarization characteristics

A new type of shaped-beam radar antenna having good polarization characteristics is described. This antenna is composed of a dual doubly curved reflector system and a feed horn with good axial ratio, such as a dual-mode horn. The rotationally symmetrical beam of the feed horn can be converted into a shaped beam by the reflector system without degradation of the axial ratio. The design of this type antenna is discussed and the experimental results of a model antenna with a cosecant squared beam are shown. Integrated cancellation ratio of the model was 22 dB.     

An integrated control method for a wind farm to reduce frequency deviations in a small power system

Output power of wind turbine generator (WTG) is not constant and fluctuates due to wind speed changes. To reduce the adverse effects of the power system introducing WTGs, there are several published reports on output power control of WTGs detailing various researches based on pitch angle control, variable speed wind turbines, energy storage systems, and so on. In this context, this paper presents an integrated control method for a WF to reduce frequency deviations in a small power system. In this study, the WF achieves the frequency control with two control schemes: load estimation and short-term ahead wind speed prediction. For load estimation in the small power system, a minimal-order observer is used as disturbance observer. The estimated load is utilized to determine the output power command of the WF. To regulate the output power command of the WF according to wind speed changing, short-term ahead wind speed is predicted by using least-squares method. The predicted wind speed adjusts the output power command of the WF as a multiplying factor with fuzzy reasoning. By means of the proposed method, the WF can operate according to the wind and load conditions. In the WF system, each output power of the WTGs is controlled by regulating each pitch angle. For increasing acquisition power of the WF, a dispatch control method also is proposed. In the pitch angle control system of each WTG, generalized predictive control (GPC) is applied to enhance the control performance. Effectiveness of the proposed method is verified by the numerical simulations.     

Output power dispatch control for a wind farm in a small power system

Nowadays, a wind turbine generator (WTG) is required to provide control capabilities as the output power of WTG fluctuates. Under this scenario, this paper proposes an output power control method of a wind farm (WF) connected to a small power system using pitch angle control. In this control approach, the WF output power control is achieved by two control levels: central and local. In the central control, the WF output power command is determined by considering the frequency deviations and wind speeds using a fuzzy function. Then, the local output power commands for each of the WTGs are based on the proposed dispatch control. In the proposed dispatch control, the output commands of each WTG are determined by considering wind conditions for each of the WTGs. The simulation results by using an actual detailed model for the wind power system show the effectiveness of the proposed method. Copyright © 2010 John Wiley & Sons, Ltd.     

Sensor-less maximum power point tracking control for wind generation system with squirrel cage induction generator

This paper proposes a technique that determines the optimal windmill operation speed and the optimal rotor flux. Moreover, the position and speed sensor-less wind generation system using the electromotive voltage observer to estimate rotor position and full-order observer to estimate rotor speed and the windmill output torque are proposed. The position and speed sensor-less maximum power point of wind power generation system is controlled by using the above estimated values, optimized windmill operation speed for maximum output power and optimized rotor flux for minimum generator losses. The effectiveness of the position and speed sensor-less maximum power point tracking control for wind power generation system with squirrel cage induction generator is verified by simulations. The simulation results confirm that the proposed method can estimate the operation speed efficiently.     

Surface Structure of Converter Slag Stabilized by Heating

Converter slag contains free lime (CaO) and unstable iron oxides (FeO, FeOOH) that may lead to expansive self-destruction. A typical industry practice for converter slag has been stabilization by steam curing and autoclaving; however, the stabilization can only reach the surface, and not the inside, of slag particles. A new method is proposed in this study to stabilize the converter slag by heating at a low temperature. After magnetic separation, specimens of converter slag were subjected to heating for 2 h at a temperature of 500°C, resulting in a decrease of free lime content irrespective of the particle size. This effect was attributed to the formation of Ca₂Fe₉O₁₃ and complicated apatite groups owing to the heating. The iron oxides in the converter slag were analyzed by X-ray photoelectron spectra. It was found that after heating, the unstable FeO (wustite) content decreased and an oxidized α-Fe₂O₃ (hematite) increased. This led to the prevention of the iron-induced expansion. The rate of heat liberation by the free lime in converter slag was smaller than that of the reagent CaO. This suggests that the presumed free lime is in a different form based on the Ca bond energy in the surface of slag particles.     

Consistency of lumbar discograms of the same disc obtained twice at a 2-week interval: influence of needle tip position

: Although numerous papers have emphasized the importance of accurate needle positioning in lumbar discography, no concrete evidence is available to support this contention, and no study has evaluated the image consistency of discography as influenced by this factor. By observing the consistency of two images in relation to needle tip position we aimed to clarify the importance of needle positioning in discography. One hundred and ninety-two patients (324 discs) receiving steroid intradiscal therapy in whom discography of the same disc was performed twice at a 2-week interval and in whom the needle tip position was within the acceptable range (as defined by us) were studied. The patients were divided into two groups: in group G, in whom the needle tip was within a limited range on both discograms, and group P, in whom the needle tip was in this range on only one discogram. Image consistency was compared roentgenographically in the two groups. The consistent image rate for the total number of discs was 48.5%, being significantly higher in group G (53.2%) than in group P (39.0%). The rates were lower in the nucleus pulposus and the posterior portion of the disc than in the other disc areas, but were significantly higher in group G (85. 4% and 75.0%, respectively, for these two areas). The necessity for accurate needle tip positioning was proved roentgenographically.     

Unit commitment by heuristics and absolutely stochastic simulated annealing

A new approach to unit commitment problem is presented using absolutely stochastic simulated annealing method. In every iteration, a solution is taken with a certain probability. Typically in simulated annealing minimisation method, a higher cost feasible solution is accepted with temperature-dependent probability; however, other solutions are accepted deterministically. That may lead to the near optimisation slowly. However, all the solutions of both higher and lower costs, are associated with acceptance probabilities to make an early jump from one local minimum to other so that it can search and compare more local minima within the same time/iteration limit. Besides, the number of bits flipping is decided by the appropriate distribution. Excess units with system-dependent probability distribution handle constraints efficiently. Sensitivity of the distribution parameters is tolerable. To reduce economic load dispatch calculations, a sign bit vector is introduced as well. The proposed method is then tested using the reported problem data set. Simulation results are compared to previous reported results. Numerical results show an improvement in solution cost and time compared to the results obtained from powerful algorithms