Analysis of shielded microstrip lines with arbitrary metallizationcross section using a vector finite element method

The finite element method (FEM) with the high-order mixed-interpolation-type triangular element is used to solve the problem of practical microstrip lines with arbitrary metallization cross section. Analyses are carried out to produce the frequency characteristics of propagation constant, characteristic impedance, and attenuation constant of shielded microstrip lines with rectangular, trapezoidal, and semi-trapezoidal strip cross sections. A comparison of the numerical results with those of the existing results shows good agreement and thus verifies the versatility of the FEM. Also, the numerical results show the effects of the metallization cross sections on the transmission properties and thus emphasize the importance of considering the practical microstrip configurations in the design of miniaturized MMICs     

Quantitative trait loci affecting 4-nitroquinoline 1-oxide-induced tongue carcinogenesis in the rat

The incidence of tongue carcinomas (TCs) induced by oral administration of 4-nitroquinoline 1-oxide in rats is strain dependent. The inbred Dark-Agouti (DA) strain showed a much higher susceptibility to large mass-forming infiltrative TCs than did the Wistar-Furth (WF) strain. Our previous study (M. Kitano et al, Jpn. J. Cancer Res., 87: 1097-1101, 1996) on crosses between these two strains postulated a dominant susceptibility gene in DA and a dominant resistance gene in WF rats. The present study mapped these loci by analyzing the backcrosses to each parent with simple sequence repeat polymorphisms. Five quantitative parameters were analyzed: (a) the number of TCs > 5 mm in diameter; (b) the total number of TCs per rat; (c) the diameter of the largest TCs (DTCmax values); (d) the number of non-TC cancers per rat; and (e) and the number of cancers of any site per rat. All of these parameters were closely correlated (P < 0.0001). DA rats had a semidominant gene (Stc1) favoring the development of 4-nitroquinoline 1-oxide-induced cancers on chromosome 19, closely linked to D19Mit9. Peak linkage was observed 4 cM distal from D19Mit9, with a logarithm of the odds (lod) score of 5.72 for the number of large TCs and 6.08 for the DTCmax. On the other hand, WF rats had a semidominant gene (Rtc1) mapped between D1Mit1 and D1Mit3, approximately 20 cM from D1Mit1, with a peak lod score of 3.30 for both the number of large TCs and the DTCmax. The main effect of Rtc1 seemed to be to reduce the size of the TCs. The action of these genes was dose dependent and cooperative. The final incidence of TC in DA, WF, F1, and backcross rats seemed to be explained by combinations of genotype at these two loci. Possible candidate genes for Stc1 and Rtc1 are discussed.     

The effect of gas atmospheres on resistivity of indium tin oxide films at high temperature

The effects of heat treatment in Q₂, O₂ and N₂, and Ar gases on the high temperature (500 C) electrical resistivity of indium tin oxide (ITO) film 52 nm thick prepared by chemical spray pyrolysis method were studied. The partial oxygen pressure effect on the resistivity was found to be to . The resistivity changes for cyclic exchange of O₂ by Ar gas at 500 C. These lead to the conclusion that chemisorption of oxygen atoms in the film surface is dominant for this thin film, for thicker films such as 640 nm oxygen diffusion is found to occur. The Langmuir model of the monolayer isothermal adsorption of oxygen atoms in the surface is applicable to the rapid change of resistivity.     

Alteration of substrate specificity of cholesterol oxidase from Streptomyces sp. by site-directed mutagenesis

Despite the structural similarities between cholesterol oxidasefrom Streptomyces and that from Brevibacterium, both enzymesexhibit different characteristics, such as catalytic activity,optimum pH and temperature. In attempts to define the molecularbasis of differences in catalytic activity or stability, substitutionsat six amino acid residues were introduced into cholesteroloxidase using site-directed mutagenesis of its gene. The aminoacid substitutions chosen were based on structural comparisonsof cholesterol oxidases from Streptomyces and Brevibacterium.Seven mutant enzymes were constructed with the following aminoacid substitutions: L117P, L119A, L119F, V145Q, Q286R, P357Nand S379T. All the mutant enzymes exhibited activity with theexception of that with the L117P mutation. The resulting V145Qmutant enzyme has low activities for all substrates examinedand the S379T mutant enzyme showed markedly altered substratespecificity compared with the wild-type enzyme. To evaluatethe role of V145 and S379 residues in the reaction, mutantswith two additional substitutions in V145 and four in S379 wereconstructed. The mutant enzymes created by the replacement ofV145 by Asp and Glu had much lower catalytic efficiency forcholesterol and pregnenolone as substrates than the wild-typeenzyme. From previous studies and this study, the V145 residueseems to be important for the stability and substrate bindingof the cholesterol oxidase. In contrast, the catalytic efficiencies(k_cat/K_m) of the S379T mutant enzyme for cholesterol and pregnenolonewere 1.8- and 6.0-fold higher, respectively, than those of thewild-type enzyme. The enhanced catalytic efficiency of the S379Tmutant enzyme for pregnenolone was due to a slightly high k_catvalue and a low K_m value. These findings will provide severalideas for the design of more powerful enzymes that can be appliedto clinical determination of serum cholesterol levels and assterol probes.     

Pressureless low temperature sintering of nanocrystalline zirconia ceramics via dry powder processing

Pressureless sintering approaches provide a simple avenue to manufacture dense ceramic parts with minimal processing equipment, but current pressureless sintering techniques have yet to demonstrate capabilities of producing dense ceramics while maintaining sub-50 nm grain sizes. Nanocrystalline yttria stablized zirconia ceramics were process from 4 mol% yttria stablized zirconia (4YSZ) nanopowders with a crystallite size of 7.5 nm using dry cold isostatic pressing (CIP) where powders are dried immediately prior to green compact formation and CIP vacuum bagging. It is shown that CIP pressures >75 000 psi (517 MPa) effectively remove pores larger than 100 nm and that pressureless sintering occurs at reduced temperatures for green densities ≥50%. Though the sintering kinetics are shown to be similar to other zirconia nanopowder sintering studies, the small initial crystallize size and reduced sintering temperature allowed densities as high as 97.2%, while retaining a ceramic grain size at or below 40 nm. Produced nanocrystalline 4YSZ ceramics with a grain size of 30.3 nm and a density of 96.3% had Vicker's hardnesses as high as 14.2 GPa and Vicker's indentation fracture resistance of 3.43 MPa·, demonstrating that simple processing approaches can be refined to fabricate nanocrystalline ceramics while maintaining high hardness and indentation fracture resistance.     

Measurement of self-diffusion coefficients in Li ionic conductors by using the short-lived radiotracer of 8Li

For the effective use of short-lived radioactive beams, soon to be available at the Tokai Radioactive Ion Accelerator Complex, the authors have developed a radiotracer method for diffusion studies in solids. The experimental test was performed by the measurement of the diffusion coefficients of Li in a sample of the compound βLiAl using an α-emitting radiotracer of ⁸Li (T_1/2=0.84 s). It was found that the time-dependent yields of the α particles from the diffusing ⁸Li that was initially implanted in the sample could be used as a measure of the diffusivity of the tracer in a nondestructive way. The method was applied to measure the self-diffusion coefficients of Li in βLiGa, and for investigating how the Li diffusion in the Li ionic conductors is affected by the concentration of atomic defects (i.e., the existence of the atomic vacancies of Li and the defects in Ga sites that are replaced by Li).     

Compact and unified hardware architecture for SHA-1 and SHA-256 of trusted mobile computing

This paper presents a compact and unified hardware architecture implementing SHA-1 and SHA-256 algorithms that is suitable for the mobile trusted module (MTM), which should satisfy small area and low-power condition. The built-in hardware hash engine in a MTM is one of the most important circuit blocks and dominates the performance of the whole platform because it is used as a key primitive to support most MTM commands concerning to the platform integrity and the command authentication. Unlike the general trusted platform module (TPM) for PCs, the MTM, that is to be employed in mobile devices, has very stringent limitations with respect to available power, circuit area, and so on. Therefore, MTM needs the spatially optimized architecture and design method for the construction of a compact SHA hardware. The proposed hardware for unified SHA-1 and SHA-256 component can compute a sequence of 512-bit data blocks and has been implemented into 12,400 gates of 0.25 μm CMOS process. Furthermore, in the processing speed and power consumption, it shows the better performance in comparison with commercial TPM chips and software-only implementation. The highest operation frequency and throughput of the proposed architecture are 137 MHz and 197.6 Mbps, respectively, which satisfy the processing requirement for the mobile application.     

Piezoelectric Sensors Operating at Very High Temperatures and in Extreme Environments Made of Flexible Ultrawide-Bandgap Single-Crystalline AlN Thin Films

Extreme environments are often faced in energy, transportation, aerospace, and defense applications and pose a technical challenge in sensing. Piezoelectric sensor based on single-crystalline AlN transducers is developed to address this challenge. The pressure sensor shows high sensitivities of 0.4–0.5 mV per psi up to 900 °C and output voltages from 73.3 to 143.2 mV for input gas pressure range of 50 to 200 psi at 800 °C. The sensitivity and output voltage also exhibit the dependence on temperature due to two origins. A decrease in elastic modulus (Young's modulus) of the diaphragm slightly enhances the sensitivity and the generation of free carriers degrades the voltage output beyond 800 °C, which also matches with theoretical estimation. The performance characteristics of the sensor are also compared with polycrystalline AlN and single-crystalline GaN thin films to investigate the importance of single crystallinity on the piezoelectric effect and bandgap energy-related free carrier generation in piezoelectric devices for high-temperature operation. The operation of the sensor at 900 °C is amongst the highest for pressure sensors and the inherent properties of AlN including chemical and thermal stability and radiation resistance indicate this approach offers a new solution for sensing in extreme environments.     

Negative regulation by interleukin-3 (IL-3) of mouse early B-cell progenitors and stem cells in culture: transduction of the negative signals by betac and betaIL-3 proteins of IL-3 receptor and absence of negative regulation by granulocyte-macrophage colony-stimulating factor

The receptors for interleukin-3 (IL-3), granulocyte-macrophage colony-stimulating factor (GM-CSF), and IL-5 share a common signaling subunit betac. However, in the mouse, there is an additional IL-3 signaling protein, betaIL-3, which is specific for IL-3. We have previously reported that IL-3 abrogates the lymphoid potentials of murine lymphohematopoietic progenitors and the reconstituting ability of hematopoietic stem cells. We used bone marrow cells from betac- and betaIL-3-knock-out mice to examine the relative contributions of the receptor proteins to the negative regulation by IL-3. First, we tested the effects of IL-3 on lymphohematopoietic progenitors by using lineage-negative (Lin-) marrow cells of 5-fluorouracil (5-FU)-treated mice in the two-step methylcellulose culture we reported previously. Addition of IL-3 to the combination of steel factor (SF, c-kit ligand) and IL-11 abrogated the B-lymphoid potential of the marrow cells of both types of knock-out mice as well as wild-type mice. Next, we investigated the effects of IL-3 on in vitro expansion of the hematopoietic stem cells. We cultured Lin-Sca-1-positive, c-kit-positive marrow cells from 5-FU-treated mice in suspension in the presence of SF and IL-11 with or without IL-3 for 7 days and tested the reconstituting ability of the cultured cells by transplanting the cells into lethally irradiated Ly-5 congenic mice together with "compromised" marrow cells. Presence of IL-3 in culture abrogated the reconstituting ability of the cells from both types of knock-out mice and the wild-type mice. In contrast, addition of GM-CSF to the suspension culture abrogated neither B-cell potential nor reconstituting abilities of the cultured cells of wild-type mice. These observations may have implications in the choice of cytokines for use in in vitro expansion of human hematopoietic stem cells and progenitors.