In situ measurements of human cough aerosol hygroscopicity

The airborne dynamics of respiratory droplets, and the transmission routes of pathogens embedded within them, are governed primarily by the diameter of the particles. These particles are composed of the fluid which lines the respiratory tract, and is primarily mucins and salts, which will interact with the atmosphere and evaporate to reach an equilibrium diameter. Measuring organic volume fraction (OVF) of cough aerosol has proved challenging due to large variability and low material volume produced after coughing. Here, the diametric hygroscopic growth factors (GF) of the cough aerosol produced by healthy participants were measured in situ using a rotating aerosol suspension chamber and a humidification tandem differential mobility analyser. Using hygroscopicity models, it was estimated that the average OVF in the evaporated cough aerosol was 0.88 ± 0.07 and the average GF at 90% relative humidity (RH) was 1.31 ± 0.03. To reach equilibrium in dry air the droplets will reduce in diameter by a factor of approximately 2.8 with an evaporation factor of 0.36 ± 0.05. Hysteresis was observed in cough aerosol at RH = ∼35% and RH = ∼65% for efflorescence and deliquescence, respectively, and may depend on the OVF. The same behaviour and GF were observed in nebulized bovine bronchoalveolar lavage fluid.     

Mechanics of plain-woven fabrics for inflated structures

Pressurized fabric tubes, pressure-stabilized beams (known as air beams) and air-inflated structures are considered to be valuable technologies for lightweight, rapidly deployable structures. Design optimization of an inflated structure depends on a thorough understanding of woven fabric mechanics. In this paper the bending response of woven pressure-stabilized beams have been experimentally tested and analytically investigated. Additionally, the micromechanical effects of interacting tows have been studied through finite element models containing contact surfaces and nonlinear slip/stick conditions. Local unit cell models consisting of pairs of woven tows were created to characterize the effective constitutive relations. The material properties from the unit cell models were then used for the global continuum model subjected to 4-point flexure. An experimental set-up was designed and manufactured for testing of Vectran and PEN air beams. The air beam mid-span deflections were measured as functions of inflation pressure and bending load. Plots of the elastic and shear moduli with respect to the pressure and coefficient of friction have been generated. It was determined that the effective elastic and shear moduli were functions of inflation pressure, the material used and the geometry of the weave. It was shown that pneumatic or pressurized tube structures differ fundamentally from conventional metal structures.     

Benchmarking performance of machine and deep learning-based methodologies for Urdu text document classification

Neural Computing and Applications - In order to provide benchmark performance for Urdu text document classification, the contribution of this paper is manifold. First, it provides a publicly...     

Analytical Modeling of Short-Channel Fully-Depleted Triple Work Function Metal Gate (TWFMG) SOI MESFET

Silicon - In this paper, a new structure: triple work function metal gate SOI MESFET, intended for integration into the deep-submicron CMOS technology, is proposed. The gate of the device consists...     

Experimental determination of gas holdup and volumetric mass transfer coefficient in a jet bubbling reactor

The hydrodynamics and mass transfer characteristics of a lab-scale jet bubbling reactor(JBR) including the gas holdup, volumetric mass transfer coefficient and specific interfacial area were assessed experimentally investigating the influence of temperature, p H and superficial gas velocity. The reactor diameter and height were 11 and 30 cm,respectively. It was equipped with a single sparger, operating at atmospheric pressure, 20 and 40℃, and two p H values of 3 and 6. The height of the liquid was 23 cm, while the superficial gas velocity changed within 0.010–0.040 m·s~(-1) range. Experiments were conducted with pure oxygen as the gas phase and saturated lime solution as the liquid phase. The liquid-side volumetric mass transfer coefficient was determined under unsteady-state oxygen absorption in a saturated lime solution. The gas holdup was calculated based on the liquid height change, while the specific interfacial area was obtained by a physical method based on the bubble size distribution(BSD) in different superficial gas velocities. The results indicated that at the same temperature but different p H, the gas holdup variation was negligible, while the liquid-side volumetric mass transfer coefficient at the p H value of 6 was higher than that at the p H = 3. At a constant p H but different temperatures, the gas holdup and the liquid-side volumetric mass transfer coefficients at 40℃ were higher than that of the same at 20℃. A reasonable and appropriate estimation of the liquid-side volumetric mass transfer coefficient(kla) in a pilot-scale JBR was provided which can be applied to the design and scale-up of JBRs.     

Development of GEP-based functional relationship for sediment transport in tropical rivers

This study presents gene expression programming (GEP), which is an extension to genetic programming (GP), as an alternative approach to modeling the functional relationships for the River Kurau, River Langat, and River Muda of the Malaysia. A functional relation has been developed using GEP with non-dimensional variables. The development of a GEP non-dimensional model is described. This paper compares current prediction equation with the existing GEP model for the same rivers (Zakaria et al. in Sci Total Environ 408:5078–5085, (2010). The presented model in this study is a less input GEP model and that predicts good performance. The proposed GEP approach gives satisfactory results compared to existing predictors.     

A secure and improved multi server authentication protocol using fuzzy commitment

Multimedia Tools and Applications - The advancement in communication and computation technologies has paved a way for connecting large number of heterogeneous devices to offer specified services....     

A principled approach to programming with nested types in Haskell

Initial algebra semantics is one of the cornerstones of the theory of modern functional programming languages. For each inductive data type, it provides a Church encoding for that type, a build combinator which constructs data of that type, a fold combinator which encapsulates structured recursion over data of that type, and a fold/build rule which optimises modular programs by eliminating from them data constructed using the buildcombinator, and immediately consumed using the foldcombinator, for that type. It has long been thought that initial algebra semantics is not expressive enough to provide a similar foundation for programming with nested types in Haskell. Specifically, the standard folds derived from initial algebra semantics have been considered too weak to capture commonly occurring patterns of recursion over data of nested types in Haskell, and no build combinators or fold/build rules have until now been defined for nested types. This paper shows that standard folds are, in fact, sufficiently expressive for programming with nested types in Haskell. It also defines buildcombinators and fold/build fusion rules for nested types. It thus shows how initial algebra semantics provides a principled, expressive, and elegant foundation for programming with nested types in Haskell.