The method of double averaging: an approach for modeling power-factor-correction switching converters

This paper describes the modeling of power-factor-correction converters under average-current-mode control, which are widely used in switch-mode power supply applications. The objective is to identify stability boundaries in terms of major circuit parameters for facilitating design of such converters. The approach employs a double averaging procedure, which first applies the usual averaging over the switching period and subsequently applies generalized averaging over the mains period. The resulting model, after two averaging steps and application of a harmonic balance procedure, is nonlinear and capable of describing the low-frequency nonlinear dynamics of the system. The parameter ranges within which stable operation is guaranteed can be accurately and easily found using this model. Experimental measurements are provided for verification of the analytical results.     

A novel method for elimination of line-current harmonics insingle-stage PFC switching regulators

This paper studies a particular single-stage power-factor-correction (PFC) switching regulator employing a discontinuous-conduction-mode (DCM) boost-input cell and a continuous-current-mode (CCM) forward output cell. Although this single-stage PFC regulator can provide a reasonably high power factor when its PFC stage is operating in discontinuous mode, substantial reduction in line-current harmonics is possible by applying a suitable frequency-modulation scheme. This paper derives a frequency-modulation scheme and proposes a practical implementation using a simple translinear analog circuit. A quantitative analysis on the total harmonic distortion (THD) of the line current when the circuit is subject to a limited range of frequency variations is presented along with some considerations for practical design. Experimental data obtained from a prototype confirms the effectiveness of the proposed frequency-modulation scheme. The proposed analog translinear circuit allows custom integrated circuit implementation, making it a viable low-cost solution to the elimination of line-current harmonics in switching regulators     

The stress-whitened damage zone of PVC blends

The stress-whitened damage zone that formed ahead of a semicircular notch during slow tensile loading has been measured from optical micrographs of translucent blends of poly(vinyl chloride) (PVC) with experimental chlorinated polyethylene (CPE) resins. When the zone was small, the plane strain condition applied and from the elastic stress distribution a constant mean stress condition was found at the boundary of the crescent-shaped zone. The critical mean stress did not depend on the chlorine content or the chlorine distribution of the experimental CPE resin used in the blend. While the critical mean stress decreased as the amount of CPE in the blend was increased, the critical volume strain, calculated from the bulk modulus, was independent of composition and was thought to be the controlling parameter for stress-whitening. When the zone was larger, the shape was qualitatively described by concepts of stress redistribution in the presence of a plastic zone ahead of the notch. Macroscopic flow and necking were only detected near the maximum in the stress-displacement curve.     

Fast‐scale bifurcation in power‐factor‐correction buck‐boost converters and effects of incompatible periodicities

In this paper, we derive the discrete‐time model for the power‐factor‐correction (PFC) buck‐boost converter in terms of a stroboscopic switching map. Fast‐scale instability is analysed through a fold diagram, which exposes the periodicity of the operation as well as the locations of the critical phase angles of the line voltage at which instability begins to occur along a half‐line cycle. The asymmetrical locations of the critical phase angles along a half‐line cycle is explained in terms of ‘under‐developed’ bifurcation. Border collision bifurcations are observed and analysed in detail. Copyright © 2006 John Wiley & Sons, Ltd.     

Reduction of EMI emission from power converter using soft-switchingtechniques

Measured, conducted, and radiated electromagnetic interference (EMI) from a hard-switched flyback converter and a soft-switched converter of the same power are presented. Results indicate that the EMI emission can be substantially reduced by using the soft-switching technique in power converters     

Adaptive Fault Monitoring in All-Optical Networks Utilizing Real-Time Data Traffic

We propose a novel fault detection and localization scheme for all-optical networks with the information of real-time data traffic. Our adaptive fault localization framework is based on combining passive and proactive monitoring solutions, together with adaptive management in two phases. Numerical results indicate that our proposed scheme has good scalability, in terms of the number of fault monitors required. Also, we show that our framework allows more flexible network design, and requires much less monitoring bandwidth when compared with the passive monitoring solutions.     

Modification of a carbon/carbon composite with a thermosetting resin precursor as a matrix by the addition of carbon black

Carbon/carbon composites were made through the pyrolysis of stabilized PAN felt and phenolic resin with the addition of 5 or 10 wt % carbon black to the matrix and then heat treatment at 600–2500°C. The effects of adding carbon black to the matrix precursor on the physical properties, microstructure, and mechanical properties of the resultant composites were investigated. Adding carbon black not only reduced the weight loss but also limited the shrinkage of the resultant composites. Adding carbon black also accelerated the formation of carbon basal planes in the matrix. At 2500°C, the crystalline stacking height in the composite with 10 wt % added carbon black was 200% greater than that with no additive. The flexural strength of the composite also increased from 15 to 42 MPa (almost 300%). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 333–337, 2006     

Prediction of carbon dioxide gas hydrate formation conditions in aqueous electrolyte solutions

A methodology for predicting the incipient equilibrium conditions for carbon dioxide gas hydrates in the presence of electrolytes such as NaCl, KCl and CaCl₂ is presented. The method utilizes the statistical thermodynamics model of van der Waals and Platteeuw (1959) to describe the solid hydrate phase. Three different models were examined for the representation of the liquid phase: Chen and Evans (1986), Zuo and Guo (1991), and Aasberg-Petersen et al. (1991). It was found that the model of Zuo and Guo (1991) gave the best results for predicting incipient CO₂ gas hydrate conditions in aqueous single salt solutions. The model was then extended for prediction of CO₂ gas hydrates in mixed salts solutions. The predictions agree very well with experimental data.