A probabilistic method for the design of power grounding systems

An improved multivariable, probabilistic method for the safety analysis of power grounding systems is presented. The application of this method is demonstrated in four examples. The first three examples illustrate the practical evaluation of one new and two existing substation grounding grids when the substation is connected to an overhead distribution system. The fourth example ascertains the relative impact of a difference between the S curve of IEC Publication 479 and Dalziel's equation for the allowable body current used in ANSI/IEEE Std 80-1986 on the validity of an exposure model based on the requirements of Std 80. In this example, the statistical data on ground faults have been taken from actual system records. Further possible refinements of the exposure model are discussed     

Investigation of the basic creep of concrete by acoustic emission

The physical origins of the basic creep of concrete are still poorly understood even though some researchers have proposed hypotheses concrening the physical mechanisms that govern this delayed behaviour of concrete. A very complete summing up of these hypotheses was produced, in the past, by, Neville; he shows that none of them, provides a satisfactory explanation of the bulk of basic creep. More recently, Rossi has proposed a new hypothesis, which has been the subject of several articles. This article concerns the use of the acoustic emission technique as a ‘tool’ to provide information on the pertinence of the physical hypothesis advanced by Rossi. The counting of the total number of acoustic events together with a frequency analysis of the acoustic emission signals indicate that there is a strong correlation between the basic creep of concrete and the creation of microcracks in the material.     

Information Visualization Within a Digital Video Library

The Informedia Digital Video Library contains over a thousand hours of video, consuming over a terabyte of disk space. This paper summarizes the multimedia abstractions used to represent this video in prior systems and introduces the visualization techniques employed to browse and navigate multiple video documents at once.     

From LTL to unambiguous Büchi automata via disambiguation of alternating automata

Formal Methods in System Design - Due to the high complexity of translating linear temporal logic (LTL) to deterministic automata, several forms of “restricted” nondeterminism have been...     

Cation Effect on the Binary and Ternary Phase Behaviors of Double-Tailed Methanesulfonate Amphiphiles

A series of symmetrical dialkyl methanesulfonate amphiphiles [DiC _n CHSO ₃ ] _m M (n = 6, 7, 8) with different counter cations (M^m+ = H⁺, Li⁺, Na⁺, K⁺, Cu²⁺, Zn²⁺, Mg²⁺, Ca²⁺, Sc³⁺) were synthesized in five steps. Their solubility and critical micelle concentration (CMC) in water were determined highlighting a huge effect of the chain length and the nature of the cation. The hydrophilic–lipophilic balance of the surfactants were assessed with the phase inversion temperature (PIT)-slope method based on the deviation from the PIT of the reference C₁₀E₄/n-octane/0.01 M NaCl_(aq) emulsion through addition of increasing amounts of the dialkyl methanesulfonates. The hydrophilicity of the surfactants was thus ranked in terms of dPIT/dx_sulfonate. A “cation” scan with the [DiC ₆ CHSO ₃ ] _m M /benzene/water systems at f_w = 0.5 was finally performed confirming the hydrophilicity ranking obtained with the PIT-slope method. It revealed that the [DiC ₆ CHSO ₃ ] ₂ Mg behaves as a “Balanced Surfactant” able to form spontaneously a three-phase microemulsion system (Winsor III) just in the presence of water and oil, in the same way as the catalytic surfactant dimethyldioctylammonium molybdate, which has the same PIT-slope.     

Polymerization and characterization of ethylene/propylene and ethylene/1-octene copolymers produced with bridged Zr- and Hf-based metallocenes

Ethylene/propylene (E/P) and ethylene/1-octene (E/O) copolymers were polymerized with two bridged metallocene catalyst systems, Et(Ind)₂ZrCl₂/MAO and Et(Ind)₂HfCl₂/MAO, respectively. The copolymers produced and some commercial reference copolymers were characterized by DSC, SEC, DMA and ¹³C NMR. The Hf-catalysed E/P polymerizations showed much lower activities than the corresponding Zr-catalysed polymerizations but gave polymers with high molar mass. The Hf-based copolymers also showed two melting peaks which may be indicative of several active sites of the catalyst. A comparison of E/P copolymers, containing about 20 mol-% propylene and produced with Zr, Hf and homogeneous V-catalysts, respectively, indicated that the Hf and V-catalysts gave material more similar to each other. The E/O copolymers produced with Zr-catalysts gave very low molar masses and the reactivity ratios, calculated from the NMR data, indicated that the Hf-catalyst has a slightly higher reactivity for 1-octene and the Zr-catalyst some better reactivity for ethylene. Segregation fractionation studies by DSC indicated that a lower 1-octene feed gives more heterogeneous copolymers and the DMA measurements reveal the existence of a linear correlation between the 1-octene content and the intensity of the tan δ_max peak.     

Rheological properties of hyperbranched polymer/poly(ethylene terephthalate) reactive blends

The rheological properties in solution, in shear and in uniaxial elongation of poly(ethylene terephthalate) (PET) reacted together with hyperbranched polymers (HBPs) were investigated. Two different PET grades, of low and high molecular weights, were compounded with sub‐ to over‐stoichiometric concentrations of HBPs of second and fourth pseudo‐generation, and subsequently subjected to a solid‐state polycondensation (SSP). The formation of microgels, which occurs at high HBP concentration, gave rise to a large increase in melt elasticity and a related decrease in melt strength. At low HBP concentrations, the complex viscosity of the unreacted HBP/PET was considerably reduced, thus demonstrating a lubrication effect of the HBP molecules. During SSP, the intrinsic and shear viscosities exhibited a gradual increase, which was similar for both PET and HBP/PET blends, and was correlated to an increase in molecular weight, through linear‐chain extension and branching reactions. The elongational viscosity of the reactive blends was also increased as a function of reaction time, and this increase was much larger in the case of the HBP/PET blends. A 400% increase in melt strength of the PET was obtained by combining SSP and trace amounts of an HBP of second generation, without any decrease in drawability.     

Effect of Molybdenum on the Structure and on the Crystallization of SiO2–Na2O–CaO–B2O3 Glasses

Crystallization of the poorly durable Na₂MoO₄ phase able to incorporate radioactive cesium must be avoided in SiO₂–Al₂O₃–B₂O₃–Na₂O–CaO glasses developed for the immobilization of Mo-rich nuclear wastes. Increasing amounts of B₂O₃ and MoO₃ were added to a SiO₂–Na₂O–CaO glass, and crystallization tendency was studied. Na₂MoO₄ crystallization tendency decreased with the increase of B₂O₃ concentration whereas the tendency of CaMoO₄ to crystallize increased due to preferential charge compensation of BO₄⁻ entities by Na⁺ ions. ²⁹Si MAS NMR showed that molybdenum acts as a reticulating agent in glass structure. Trivalent actinides surrogate (Nd³⁺) were shown to enter into CaMoO₄ crystals formed in glasses.