A cathode readout gas sampling calorimeter with conductive plastic tubes

We constructed and tested a prototype gas sampling electromagnetic calorimeter of the Pb-proportional tube sandwich type. The calorimeter uses conductive plastic tubes and cathode pad readout with a tower structure which resulted in reasonable energy and spatial resolutions for electrons in the momentum range 0.5–4.0 GeV/c; $\text{σ}{}_{\mathrm{E}}\text{E =}\text{21\%}\text{(E(}\text{GeV}\text{)}\text{)}{}^{\mathrm{<mtext>1</mtext><mtext>2</mtext>}}\text{, σ}{}_{\mathrm{x}}\text{= 6}\text{mm}\text{(at 3 GeV}$/c). This paper describes the test and the performance studied under various conditions.     

Beam test of the CsI(Tl) calorimeter for the BELLE detector at the KEK-B factory

We studied the performance of a prototype electromagnetic calorimeter for the BELLE detector at the KEK proton synchrotron for an energy range of 0.25–3.5 GeV. The prototype consisted of an array of 6 × 5 CsI(Tl) crystals with 30 cm length (16.2 radiation lengths) and about 6 cm × 6 cm cross section. The scintillation light of each CsI(Tl) crystal was read out by two large-area PIN photodiodes and charge-sensitive preamplifiers attached at the rear face of the crystal. We measured the energy and position resolution for electrons and the e/π separation for two sets of matrix configurations: one corresponded to the center and the other to the edge of the barrel calorimeter. The overall performance measured by the test proves that the prototype calorimeter is satisfactory for the use in the BELLE detector.     

A novel gait generation method independent of target settling-time adjustment for underactuated limit cycle walking

This paper proposes a novel gait generation method for surely achieving constraint on impact posture in limit cycle walking. First, we introduce an underactuated rimless wheel model without ankle-joint actuation and formulate a state-space realization of the control output using the stance-leg angle as a time parameter through an input–output linearization. Second, we determine a control input that moves the control output to a terminal value at a target stance-leg angle during the single-support phase. Third, we conduct numerical simulations to observe the fundamental gait properties and discuss the relationship between the gait symmetry and mechanical energy restoration. Furthermore, we mathematically prove the asymptotic stability of the generated walking gait by analytically deriving the restored mechanical energy.     

High-performance cone beam reconstruction using CUDA compatible GPUs

Compute unified device architecture (CUDA) is a software development platform that allows us to run C-like programs on the nVIDIA graphics processing unit (GPU). This paper presents an acceleration method for cone beam reconstruction using CUDA compatible GPUs. The proposed method accelerates the Feldkamp, Davis, and Kress (FDK) algorithm using three techniques: (1) off-chip memory access reduction for saving the memory bandwidth; (2) loop unrolling for hiding the memory latency; and (3) multithreading for exploiting multiple GPUs. We describe how these techniques can be incorporated into the reconstruction code. We also show an analytical model to understand the reconstruction performance on multi-GPU environments. Experimental results show that the proposed method runs at 83% of the theoretical memory bandwidth, achieving a throughput of 64.3 projections per second (pps) for reconstruction of 512³-voxel volume from 360 512²-pixel projections. This performance is 41% higher than the previous CUDA-based method and is 24 times faster than a CPU-based method optimized by vector intrinsics. Some detailed analyses are also presented to understand how effectively the acceleration techniques increase the reconstruction performance of a naive method. We also demonstrate out-of-core reconstruction for large-scale datasets, up to 1024³-voxel volume.     

Chemical vapor deposition of SiO2 films by TEOS/O2 supermagnetron plasma

A TEOS/O₂ supermagnetron double electrode plasma system was used to deposit SiO₂ films. Deposition rates were measured as a function of rf power and substrate stage temperature. With an increase of rf power on both electrodes from 40 to 80W, the deposition rate increased; however, with a further increase of rf power from 80 to 120W, the deposition rate ceased to increase or decreased only a small amount. The presence of O-H bonds from bonded water in the film was evaluated using buffered HF (BHF) etching solution. With an increase of rf power from 40 to 120W, the BHF etch rate decreased; i.e., the number of O-H bonds were reduced. A minimum BHF etch rate was observed at a rf phase difference of 180° between the two rf power sources. A SiO₂ film was deposited on a trench-patterned quartz substrate. A flat surface SiO₂ layer with air gaps (voids) was formed on the high-aspect ratio (depth/width=1.5-2) trench area.     

Development of service-oriented products based on the inverse manufacturing concept

To achieve sustainability, resource consumption and waste generation must be drastically decreased. For societal acceptance, preservation of both quality of life and corporate profits are essential. One promising approach is to shift the source of value from the amount of product sold to the quality of services the product provides. This paper describes the need for redesigning recycling systems from a manufacturing perspective and then discusses the possibility of this "servicification" of products, describing our experience with prototype development. We discuss development of product prototypes and their business, using consumer facsimile machines as an example of "service-oriented products". Traditional thought presumes that only products comprising new materials and components are valuable. Consideration of a service-oriented product can serve as a stimulus to revise this mode of thought and to control delivery and quality of disposed products. This paper also provides a life cycle simulation of the developed service-oriented business. Simulation results indicate that service-oriented business can potentially reduce environmental impact while extending business opportunities from the viewpoint of whole product life cycles.     

Fluctuations in Tracer Amounts in a Compartmental System with a Markovian Transition Process

This communication considers a method for evaluating fluctuations in the integral type output of a linear time-invariant compartmental system with a Markovian transition process. First, we derived a mathematical formula to calculate variances and covariances of integral type. outputs, as with radioisotope data, when transition rates are known. Then, an estimate for the upper limits of variances and covariances, i.e., 1/2?initial dose, when the transition rates are not given beforehand, was introduced.