复杂蒸馏的最小回流比

本文提出的直接计算方法不仅适用于多股进料的蒸馏塔,而且也适于有多股侧线抽出的情况。     

并流和逆流热交换器的流体出口温度算式

<正> 在近几年出版的一些化工原理教材有关“传热单元”的章节中,在提到确定热交换器流体出口温度时,都谈到用对数平均温差需试差求解,采用传热单元法可避免试差、比较简便的论点。在这一节的举例中,各教材或例题与习题集都以逆流或并流热交换     

侧流塔的最小回流比

蒸馏塔的设计需要估算最小回流比。本文指出如何计算有一股或多股侧流的蒸馏塔最小回流比。     

Methods of Modifying the Brittle Behavior of Cementitious Composites

We put forward effective methods of increasing the tensile strain of cementitious composites with 2% PVA fiber and high fly ash content. The test results show that curing condition has a significantly effect on the tensile performance. It is approved that the specimens incorporated appropriate volume fraction rubber powder and lightweight aggregate greatly increase the tensile strain of composites at medium-term age, but indefinitely at long-term age. To a certain extent, EVA can limitedly enhance the tensi...     

Fiber-optic epoxy composite cure sensor. I. Dependence of refractive index of an autocatalytic reaction epoxy system at 850 nm on temperature and extent of cure

We discuss the behavior of the refractive index of a typical epoxy-aromatic diamine system. Near 850 nm the index of refraction is found to be largely controlled by the density of the epoxy. Models are derived to describe its dependence on temperature and extent of cure. Within the range of temperatures studied, the refractive index decreases linearly with increasing temperature. In addition, as the epoxy is cured, the refractive index increases linearly with conversion to the gel point. From then on, shrinkage in the volume of the epoxy is restricted by local viscosity. Therefore the linear relationship between the refractive index and the extent of cure does not hold beyond the gel point.     

Fiber-optic epoxy composite cure sensor. II. Performance characteristics

The performance of a fiber-optic epoxy composite cure sensor, as previously proposed, depends on the optical properties and the reaction kinetics of the epoxy. The reaction kinetics of a typical epoxy system are presented. It is a third-order autocatalytic reaction with a peak observed in each isothermal reaction-rate curve. A model is derived to describe the performance characteristics of the epoxy cure sensor. If a composite coupon is cured at an isothermal temperature, the sensor signal can be used to predict the time when the gel point occurs and to monitor the cure process. The sensor is also shown to perform well in nonstoichiometric epoxy matrices. In addition the sensor can detect the end of the cure without calibration.     

Protein crystal growth in microgravity using a liquid/liquid diffusion method

Crystallization of proteins by liquid liquid diffusion method was performed in microgravity using the MDA Minilab aboard the US Space Shuttle. Three proteins, namely lysozyme, trichosanthin, and a new lechin, were crystallized in the space experiment. In contrast to the results of space experiments with a tube-like vapor diffusion method, the crystallization conditions for growing better crystals in space are remarkably different from the conditions optimized on earth. This may be due to difficulties in ground optimization, which are caused by gravity-dependent phenomena, in particular the specific convective flow occurring with liquid liquid diffusion.     

Objective quantification of acetylcholine receptor aggregation using fast Fourier transforms

A new approach for objectively analyzing the aggregation of acetylcholine receptors (AChRs) through power spectrum analysis derived from fast Fourier transform (FFT) of images has been developed. Presently, detection of AChR aggregates at neuromuscular junctions is not easily accomplished. Though the formation of AChR clusters results in periodic gray-level variations that differ with time, no study reporting their correlation with frequency information in the Fourier domain for aggregates' detection purposes exists. To this end, we processed time-lapse images of AChR aggregates' formation on murine myotubes to extract peak values of power spectra. To validate interpretation of the Fourier spectra analysis, a computer routine was developed to semi-automatically count AChR aggregates. We found: (1) logarithmic maxima of Fourier spectra correlated significantly with experimentation time; (2) cluster count correlated significantly with time only after clusters were discernable from images, signifying that this method heavily depended on definitive growth data and thresholding values; (3) exponents of Fourier maxima versus time and cluster count versus time profiles during this phase compared favorably, indicating that both methods were analyzing identical cluster growth rates. Our observations suggest that analysis via FFT power spectrum is sensitive and robust enough to automatically quantify AChR aggregates.     

Overcoming challenges in the study of nitrided microalloyed steels using atom probe

Nitrided steels are widely used in the engineering field due to their superior hardness and other attractive properties. Atom probe tomography (APT) was employed to study two Nb-microalloyed CASTRIP steels with different N contents. A major challenge of using APT to study this group of materials is the presence of tails after Fe peaks in the mass spectra, which overestimates the composition for alloying elements such as Nb and Cu in the steels. One important factor that contributes to the tails is believed to be delayed field evaporation from Fe²⁺. This artefact of the mass spectrum was observed to be the most severe when voltage pulsing was used. The application of laser pulses with energy ranging from 0.2 to 1.2 nJ successfully reduced the tails and lead to better compositional measurement accuracy. Spatial resolution in the z-direction (along the tip direction) was observed to be less affected by changing laser energy but deteriorates in x-y direction with increasing laser energy. This investigation suggests that pulsed-laser atom probe with ∼0.4 nJ laser energy can be used to study this group of materials with improved mass resolution while still maintaining high spatial resolution.     

Dynamical synapses enhance neural information processing: gracefulness, accuracy, and mobility

Experimental data have revealed that neuronal connection efficacy exhibits two forms of short-term plasticity: short-term depression (STD) and short-term facilitation (STF). They have time constants residing between fast neural signaling and rapid learning and may serve as substrates for neural systems manipulating temporal information on relevant timescales. This study investigates the impact of STD and STF on the dynamics of continuous attractor neural networks and their potential roles in neural information processing. We find that STD endows the network with slow-decaying plateau behaviors: the network that is initially being stimulated to an active state decays to a silent state very slowly on the timescale of STD rather than on that of neuralsignaling. This provides a mechanism for neural systems to hold sensory memory easily and shut off persistent activities gracefully. With STF, we find that the network can hold a memory trace of external inputs in the facilitated neuronal interactions, which provides a way to stabilize the network response to noisy inputs, leading to improved accuracy in population decoding. Furthermore, we find that STD increases the mobility of the network states. The increased mobility enhances the tracking performance of the network in response to time-varying stimuli, leading to anticipative neural responses. In general, we find that STD and STP tend to have opposite effects on network dynamics and complementary computational advantages, suggesting that the brain may employ a strategy of weighting them differentially depending on the computational purpose.