Inferring kinetic dissolution of NaCl in aqueous glycol solution using a low-cost apparatus and population balance model

An experimental methodology for inferring brine dissolution rate in monoethylene glycol (MEG) solutions at different temperatures using a webcam combined with a mathematical model is presented. The measurement system is designed to track the RGB (red, green, and blue) colour variations during the dissolution process. A dynamic model augmented with the population balance equation is applied to describe the dissolution process. Moreover, the dissolution rate is consistently related to the temperature and MEG concentration through the driving force based on the Gibbs energy and chemical affinity. The applied low-cost measurement apparatus proved to be a useful resource for tracking the dissolution dynamics in a wide range of undersaturation.     

Design of Polarization-independent Wavelength-interleave Coupler in Fluorinated Polyimide Waveguide

Based on the measurement of dispersion characteristic and birefractive index of the fluorinated polyimide film,a statistical optimum design method is proposed and used to realize the design of 32-and 36-wavelengths optical waveguide wavelength-interleave coupler (i,e.,interleaver) with the optimization of polarization fluctuation and wavelength interval of 0.8nm at 1550nm. The largest cross coupling ratios of the two interleavers are respectively less than 1.8% and 3.5%, while the least through coupling ratios are respectively greater than 98. 2% and 96. 5%. The output differences due to polarization fluctuation are less than 1.7% and 3.2%     

Preparation and Luminescence Spectra of Calcium- and Rare-Earth (R = Eu, Tb, and Pr)-Codoped α-SiAlON Ceramics

Rare-earth-doped oxynitride or nitride compounds have been reported to be luminescent and may then serve as new phosphors with good thermal and chemical stabilities. In this work, we report the photoluminescence (PL) spectra of europium-, terbium-, and praseodymium-doped Ca-α-SiAlON ceramics. The highly dense ceramics were prepared by hot pressing at 1750°C for 1 h under 20 MPa in a nitrogen atmosphere. Europium-doped Ca-α-SiAlON displayed a single broad emission band peaking at λ= 550–590 nm depending on the europium concentration. The emission bands in the spectra of europium-doped Ca-α-SiAlONs were assigned to the allowed transition of Eu²⁺ from the lowest crystal field component of 4 f ⁶5 d to ⁸S_7/2 (4 f ⁷) ground-state level. The emission spectra of terbium- and praseodymium-doped Ca-α-SiAlON ceramics both consisted of several sharp lines, which were attributed to the ⁵D₄→⁷F _j ( j = 3, 4, 5, 6) transitions of Tb³⁺ and ³P₀→³H _j ( j = 3, 4, 5) transitions of Pr³⁺, respectively. In particular, the terbium-doped α-SiAlON ceramics showed a strong green emission among these phosphors.     

Dissolution of phase-separated domains after a jump to a temperature in the single-phase region

Phase-separated domains prepared in the two-phase region were dissolved at a temperature in the single-phase region, and their dissolution dynamics was studied by using the time-resolved light scattering (TRLS) technique and a scanning electron microscope (SEM). The time t_ps of preparation of domains was chosen to be long enough for phase separation to proceed into the late stage. The scattered light intensity at small wavenumbers increased before it attenuated. As t_ps increased, the increase at smaller wavenumbers became more significant and the peak intensity decreased only slightly with dissolution time. The characteristic wavenumber q_m evaluated from TRLS and SEM followed the power-law relation q_mt^−0.3.     

Synthesis of polymeric microspheres employing SPG emulsification technique

Relatively uniform polymeric microspheres, the coefficients of variation being close to 10%, were obtained by the BPO-initiated suspension polymerization of styrenic monomers. Unlike the conventional stirred-tank system, a particular microporous glass membrane (SPG) provided uniform monomer droplets continuously when monomer was allowed to permeate through the micropores. The monomer droplets were suspended in an aqueous solution containing the stabilizing agents, transferred to a stirred vessel, and polymerized. Up to 10μm spheres, of a far narrower size distribution than those obtained by conventional microsuspension polymerization spheres, were obtained. The initial droplet size and distribution were retained with the successful suppression of secondary particle nucleation by the addition of hydroquinone in the aueous phase. Crosslinked polystyrene spheres were also synthesized in the presence of various low-molecular-weight diluents. While a good solvent, toluene, was not so effective; poor solvents, n-heptane and n-heptane, easily yielded the microporous structure, the specific surface area being as high as 160 m²/g. © 1994 John Wiley & Sons, Inc.     

Distributed architecture for energy management D-structure

Electric power systems are expanding in size and complexity, and the requirement for the energy management system (EMS) is becoming more important. In this computer control system, a single control computer is used mainly as the primary computer and its software is very complicated because of its hugh number of small, quick tasks to obtain high response speed. Therefore, much effort is needed to develop and modify the programs, and the responsiveness of this centralized architecture varies greatly when many faults occur in the power system. This paper describes a new distributed architecture for the EMS. Distributed processors execute the functions cooperatively with periodic access to the common bulletin board database in which information about the power system exist. This architecture facilitates the software development and maintenance, and it also enhances the performance by the parallel processing of the distributed functions.     

Characterization of nanoporous materials prepared from montmorillonite clay and its application to the decolorization of mare's milk oil

Nanoporous materials have been prepared by leaching the purified montmorillonite clay with sulfuric acid (H₂SO₄) solution with varying concentrations (0.5–2 M) at 80°C for 0.5–4 h. Acid leaching causes partial amorphisation of the clay with depletion of MgO, Al₂O₃, CaO and Fe₂O₃ components mostly from interlayer and octahedral sites. This increases the specific surface area by more than 3 times, i.e. from 49.1 to 157 m²/g. The pore-size distribution curves calculated from the adsorption isotherms of the leached montmorillonite show that most of the pores are in the mesoporous region with their diameter ranging 3–4 nm. This material turns out to be appropriate for bleaching of the mare's milk oil. The chemical and structural changes of the acid-leached montmorillonite are discussed in terms of the decolorization capacity.     

Microstructural Analysis of Liquid-Phase-Sintered β-Silicon Carbide

The microstructures of fine-grained β-SiC materials with α-SiC seeds annealed either with or without uniaxial pressure at 1900°C for 4 h in an argon atmosphere were investigated using analytical electron microscopy and high-resolution electron microscopy (HREM). An applied annealing pressure can greatly retard phase transformation and grain growth. The material annealed with pressure consisted of fine grains with β-SiC as a major phase. In contrast, the microstructure in the material annealed without pressure consisted of elongated grains with half α-SiC. Energy-dispersive X-ray analysis showed no differences in the amount of segregation of aluminum and oxygen atoms at grain boundaries, but did show a significant difference in the segregation of yttrium atoms at grain boundaries along SiC grains for the two materials. The increased segregation of yttrium ions at grain boundaries caused by the applied pressure might be the reason for the retarded phase transformation and grain growth. HREM showed a thin secondary phase of 1 nm at the grain boundary interface for both materials. The development of a composite grain consisting of a mixture of β/α polytypes during annealing was a feature common to both materials. The possible mechanisms for grain growth and phase transformation are discussed.