Open‐cycle OTEC systems with freshwater product: Effects of noncondensable gases on performance of condenser

An open‐cycle ocean thermal energy conversion (OC‐OTEC) system is one of the energy conversion methods used to generate electricity from ocean thermal energy. For the OC‐OTEC system, steam evaporated from the surface seawater due to flash evaporation drives the turbine. At that time, dissolved gas such as air is introduced into the low‐pressure system (OC‐OTEC system) as the noncondensable gas, which degrades the performance of condensation heat transfer. In this paper, a small‐scale OC‐OTEC experimental unit experimentally investigates the effect of noncondensable gas on the heat transfer performance in a condenser. The experimental results are discussed in comparison with theoretical estimation by the Sparrow–in method. It is shown that the condensation is occupied by heat and mass transfer near a condensation surface and that the condensation efficiency is affected by exhaust quantity of noncondensable gas at a relatively high concentration ratio of condensable gas. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 154(1): 29–35, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20179     

Feasibility of a 1,400 m Span Steel Cable-Stayed Bridge

This paper describes the feasibility of 1,400 m steel cable-stayed bridges from both structural and economic viewpoints. Because the weight of a steel girder strongly affects the total cost of the bridge, the writers present a procedure to obtain a minimum weight for a girder that ensures safety against static and dynamic instabilities. For static instability, elastoplastic, finite-displacement analysis under in-plane load and elastic, finite-displacement analysis under displacement-dependent wind load are conducted; for dynamic instability, multimodal flutter analysis is carried out. It is shown that static critical wind velocity of lateral torsional buckling governs the dimension of the girder. Finally, the writers briefly compare a cable-stayed bridge with suspension bridge alternatives.     

Hydraulic Model for Sedimentation in Storm-Water Detention Basins

Treatment of storm-water runoff may be necessary before discharge to surface waters. In urban areas, space constraints limit selection of conventional treatment systems, and alternative systems are needed. This research program involves design and laboratory testing of a small footprint nonproprietary detention basin which consists of pipes and box culvert sections with a specialized inlet and outlet system. This system can be placed below grade near the roadway section as part of the conventional drainage system and does not require additional right-of-way. A mathematical model, based entirely on hydraulic principles, is developed to estimate particle removal efficiency of the rectangular detention basin for the treatment of storm-water runoff by extending ideal horizontal tank theory under the condition in which water level is varied. A physical model was built in 1/5 scale to measure particle removal performance and validates the conceptual model. Experiments were performed for steady inflow conditions with different inflow rates, durations, and suspended sediment concentrations. Measured time series outflow suspended sediment concentrations and particle removal efficiency compare well with calculated results from the conceptual model. The outflow particle-size distribution can also be estimated using the conceptual model.     

Basic information on new regulatory criteria requiring on-site emergency preparedness for accelerator facilities in Japan

For basic information on new regulatory criteria, the dose rate around a thick target bombarded by proton, electron, or carbon beam having incident energy of 10 MeV–50 GeV (per nucleon in case of carbon) was simulated using the PHITS Monte Carlo code. Based on this simulation, the benchmark which is ‘1 Sv/h at 1 m away from the beam line’ assuming 1% beam loss was evaluated, and compared with the criteria in France and Canada. Based on this evaluation, a new regulatory criteria has been established for requiring on-site emergency preparedness for accelerator facilities in Japan, which is required for the ion accelerator beyond the ion beam of 100 MeV/nucleon and 0.5 kW beam power, and the electron accelerator beyond the electron beam of 50 MeV energy and 1 kW beam power.     

Fluorescent in situ hybridization analysis of open lactic acid fermentation of kitchen refuse using rRNA-targeted oligonucleotide probes

Reproducible amounts of lactic acid accumulate in minced kitchen refuse under open conditions with intermittent pH neutralization [Sakai et al., Food Sci. Technol. Res., 6, 140 (2000)]. Here, we showed that such pH-controlled open fermentation of kitchen refuse reproducibly resulted a selective proliferation of a major lactic acid bacterial (LAB) species. In one experiment, the predominant microorganisms isolated during the early phase (6 h) were Gammaproteobacteria. In contrast, those that predominated during the late phase (48 h) were always Lactobacillus plantarum in three independent experiments. To further quantify the microbial community within open lactic acid fermentation, we performed fluorescent in situ hybridization (FISH) analysis targeting 16S (23S) rRNA. We designed two new group-specific DNA probes: LAC722(L) was active for most LAB including the genera Lactobacillus, Pediococcus, Leuconostoc and Weisella, whereas Lplan477 was specific for L. plantarum and its related species. We then optimized sample preparation using lysozyme and hybridization conditions including temperature, as well as the formamide concentration and the salt concentration in the washing buffer. We succeeded in quantification of microorganisms in semi-solid, complex biological materials such as minced kitchen refuse by taking color microphotographs in modified RGB balance on pre-coated slides. FISH analysis of the fermentation of kitchen refuse indicated that control of the pH swing leads to domination by the LAB population in minced kitchen refuse under open conditions. We also confirmed that L. plantarum, which generates lactic acid in high quantities but with low optical activity, became the dominant microorganism in kitchen refuse during the late phase of open fermentation.     

Preparation of carbon microparticle assemblies from phenolic resin using an inverse opal templating method

Three-dimensionally (3D) well-ordered carbon microparticle assemblies with different particle morphologies were fabricated by infiltration of phenolic resin solution into SiO₂ inverse opal structures and subsequent carbonization. The effect of the phenolic resin solution concentration and the carbonization temperature on the morphology of the fabricated carbon microparticles was investigated. At a carbonization temperature of 1000 °C, carbon microparticles with interlocked bridges were obtained when the concentration of phenolic resin solution is 40 wt% and hollow carbon microparticles with opened window channels were obtained at a concentration of 30–35 wt%. When the carbonization temperature was decreased to 500 °C, carbon microparticles with interlocked bridges also were observed, even when the phenolic resin concentration was 30 wt%. The structures and properties of the carbon microparticles and their assemblies were characterized using SEM, XRD, and N₂ adsorption.     

Micropatterning of liquid crystalline polyacetylene derivative by using self-organization processes

Side-chain type liquid crystalline polyacetylene, which has mesogenic moieties as side chains, is one of the promising materials for practical applications in the electronics. Micropatterning of the conductive polymer is a significant issue in this field. We show a simple method to fabricate micropatterns of side-chain type liquid crystalline polyacetylene derivative. Under dry condition, stripes patterns and lattice pattern were formed based on the fingering instability and stick-slip motion of the receding meniscus. Honeycomb-patterned polymer film was obtained by casting polymer solution under humid condition. The micropatterns drastically changed by changing solution concentration and preparation conditions.     

Beer brewing using a fusant between a sake yeast and a brewer's yeast

Beer brewing using a fusant between a sake yeast (a lysine auxotrophic mutant of sake yeast K-14) and a brewer's yeast (a respiratory-deficient mutant of the top fermentation yeast NCYC1333) was performed to take advantage of the beneficial characteristics of sake yeasts, i.e., the high productivity of esters, high tolerance to ethanol, and high osmotolerance. The fusant (F-32) obtained was different from the parental yeasts regarding, for example, the assimilation of carbon sources and tolerance to ethanol. A brewing trial with the fusant was carried out using a 100-l pilot-scale plant. The fusant fermented wort more rapidly than the parental brewer's yeast. However, the sedimentation capacity of the fusant was relatively low. The beer brewed using the fusant contained more ethanol and esters compared to that brewed using the parental brewer's yeast. The fusant also obtained osmotolerance in the fermentation of maltose and fermented high-gravity wort well.     

A new scaling algorithm for the maximum mean cut problem

We present a new scaling algorithm for the maximum mean cut problem. The mean of a cut is defined by the cut capacity divided by the number of arcs crossing the cut. The algorithm uses an approximate binary search and solves the circulation feasibility problem with relaxed capacity bounds. The maximum mean cut problem has recently been studied as a dual analogue of the minimum mean cycle problem in the framework of the minimum cost flow problem by Ervolina and McCormick. A networkN=(G, lower, upper) with lower and upper arc capacities is said to be -feasible ifN has a feasible circulation when we relax the capacity bounds by ; that is, we use (lower(a)- , upper(a)+) bounds instead of (lower(a), upper(a)) bounds for each arca A. During an approximate binary search we maintain two bounds,LB andUB, such thatN is LB-infeasible andUB-feasible, and we reduce the interval size (LB, UB) by at least one-third at each iteration. For a graph withn vertices, m arcs, and integer capacities bounded byU, the running time of this algorithm is O(mn log(nU). This time bound is better than the time achieved by McCormick and Ervolina under thesimilarity condition (that is,U=O(n^o(1))). Our algorithm can be naturally used for the circulation feasibility problem, and thus provides a new scaling algorithm for the minimum cut problem.Research supported by a grant-in-aid of the Ministry of Education, Science and Culture of Japan.