Study of the morphology and mechanical properties of polypropylene composites with silica or rice‐husk

The mechanical, morphological behavior and water absorption characteristics of polypropylene (PP) and silica, or PP and rice‐husk, composites have been studied. The silica used in this study as filler was a commercial type produced from soluble glass or rice husks. The compatibilizing effect of PP grafted with monomethyl itaconate (PP‐g‐MMI) and/or with vinyltriethoxysilane (PP‐g‐VTES) as polar monomers on the mechanical properties and water absorption was also investigated. In general, a high loading of the studied fillers in the polymer matrix increases the stiffness and the water absorption capacity. This effect is more noticeable in the tensile modulus of the PP/silica composite with PP‐g‐VTES as compatibilizer. However, the increase of the rice‐husk charge as a natural filler in the PP matrix decreases the stiffness, and in the presence of PP‐g‐MMI as compatibilizer in PP/rice‐husk, the tensile modulus and water absorption of the composite were improved. The better adhesion and phase continuity in the PP/silica and PP/rice‐husk composites with different compatibilizers was confirmed by the morphological study. Copyright © 2004 Society of Chemical Industry     

Transient dynamics of cylinders under wave slamming

Large diameter slender cylindrical shells used as buoyancy chambers and support legs for compliant marine structures experience a variety of impact loadings which could induce significant levels of dynamic response. By examining the response of a typical range of cylindrical shell geometries to a simulation of the impact loading typical of wave slamming, the paper examines the likely levels and practical significance of the transient dynamic response. It shows that the levels of dynamic response are sufficiently severe to have important implications for the triggering of buckling and fatigue collapse characteristics. It is suggested that this phenomenon requires additional more-detailed consideration, including the provision of reliable predictions of transient slam pressure distributions and the levels and forms of hydrodynamic damping, as well as the effects of more practical shell and stiffening geometries, and ambient stress levels.     

Methodology for evaluating a novel education technology: a case study of handheld video games in Chile

Many school systems, in both the developed and developing world, are implementing educational technology to assist in student learning. However, there is no clear consensus on how to evaluate these new technologies. This paper proposes a comprehensive methodology for estimating the value of a new educational technology in three steps: benefit analysis, through the administration of a well-designed experiment; cost analysis, which incorporates costs to weigh against the benefits; and feasibility analysis, which introduces real-world concerns that may affect the ability to actually implement the technology. To illustrate the methodology, a case study from Chile is used where portable educational video games were introduced into first and second grade classrooms with the aim of improving learning in mathematics and language. This paper demonstrates the importance of all three steps in the evaluation process and provides a framework for future analyses.     

Determination of the Hydroxyl Value of Soybean Polyol by Attenuated Total Reflectance/Fourier Transform Infrared Spectroscopy

A rapid method for the quantitative determination of the hydroxyl value (OHV) of hydroxylated soybean oils by HATR/FTIR spectroscopy is described. Calibration standards were prepared by the formic acid/hydrogen peroxide method and OH values were determined by the official method of AOCS Tx 1a-66, covering an analytical range of 3.5–125 mg of KOH/g of sample. A partial least squares (PLS) calibration model for the prediction of the hydroxyl value (OHV) was developed based on eight different spectral subregions between 3,150 and 990 cm⁻¹ and combinations of them. On average, 36 samples were used for the modeling and 17 were used for external validation. The resulting calibration was linear over the analytical range and had a standard deviation of 2.334. Validation of the method was carried out by comparing the OHV of a series of hydroxylated soybean oils predicted by the PLS model to the values obtained by the AOCS standard method. A correlation coefficient of R ² = 0.9843 and RMSEC and RMSEP values of, respectively, 3.393 and 3.643 were obtained. After the calibration of the spectrometer, the OHV could be obtained in 2–3 min per sample, a major improvement over conventional wet chemical methods. The advantages of these methodologies are that they do not destroy the sample, have a lower cost, expedite the analysis and do not produce residues. Therefore, they may yield excellent results when used to quantify OHV of soybean polyols obtained by hydroxylation reaction.     

Influence of grafted polypropylene on the mechanical properties of mineral‐filled polypropylene composites

The purpose of this work was to study how mineral fillers would behave in a polypropylene (PP) matrix when PP modified with maleic anhydride (MA) and/or itaconic acid (IA) was used as a coupling agent in the preparation of mineral‐filled PP composites. The composites were characterized with tensile mechanical measurements and morphological analysis. The optimum amount of the coupling agent to be used to obtain composites with improved mechanical properties was established. The results indicated that these coupling agents enhanced the tensile strength of the composites significantly, and the extent of the coupling effect depended on the nature of the interface that formed. The incorporation of coupling agents enhanced the resistance to deformation of the composite. The behavior of IA‐modified PP as a coupling agent was similar to that of a commercial MA‐modified PP for the filled PP composites. Evidence of improved interfacial bonding was revealed by scanning electron microscopy studies, which examined the surfaces of fractured tensile test specimens; their microstructures confirmed the mechanical results with respect to the observed homogeneous or optimized dispersion of the mineral‐filler phase in these composites. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2343–2350, 2007     

An EM-based identification algorithm for a class of hybrid systems with application to power electronics

In this paper we present an identification algorithm for a class of continuous-time hybrid systems. In such systems, both continuous-time and discrete-time dynamics are involved. We apply the expectation-maximisation algorithm to obtain the maximum likelihood estimate of the parameters of a discrete-time model expressed in incremental form. The main advantage of this approach is that the continuous-time parameters can directly be recovered. The technique is particularly well suited to fast-sampling rates. As an application, we focus on a standard identification problem in power electronics. In this field, our proposed algorithm is of importance since accurate modelling of power converters is required in high- performance applications and for fault diagnosis. As an illustrative example, and to verify the performance of our proposed algorithm, we apply our results to a flying capacitor multicell converter.     

Exploiting User Interests to Characterize Navigational Patterns in Web Browsing Assistance

In order to be capable of exploiting context for pro-active information recommendation, agents need to extract and understand user activities based on their knowledge of the user interests. In this paper, we propose a novel approach for context-aware recommendation in browsing assistants based on the integration of user profiles, navigational patterns and contextual elements. In this approach, user profiles built using an unsupervised Web page clustering algorithm are used to characterize user ongoing activities and behavior patterns. Experimental evidence show that using longer-term interests to explain active browsing goals user assistance is effectively enhanced.

Indecomposability of free algebras in some subvarieties of residuated lattices and their bounded subreducts

In this paper, we show that free algebras in the variety of residuated lattices and some of its subvarieties are directly indecomposable and show, as a consequence, the direct indecomposability of free algebras for some classes of their bounded implicative subreducts.