Effects of SO2 on selective catalytic reduction of NO with NH3 over a TiO2 photocatalyst

The effect of SO₂ gas was investigated on the activity of the photo-assisted selective catalytic reduction of nitrogen monoxide (NO) with ammonia (NH₃) over a TiO₂ photocatalyst in the presence of excess oxygen (photo-SCR). The introduction of SO₂ (300 ppm) greatly decreased the activity of the photo-SCR at 373 K. The increment of the reaction temperature enhanced the resistance to SO₂ gas, and at 553 K the conversion of NO was stable for at least 300 min of the reaction. X-ray diffraction, FTIR spectroscopy, thermogravimetry and differential thermal analysis, x-ray photoelectron spectroscopy (XPS), elemental analysis and N₂ adsorption measurement revealed that the ammonium sulfate species were generated after the reaction. There was a strong negative correlation between the deposition amount of the ammonium sulfate species and the specific surface area. Based on the above relationship, we concluded that the deposition of the ammonium sulfate species decreased the specific surface area by plugging the pore structure of the catalyst, and the decrease of the specific surface area resulted in the deactivation of the catalyst.     

A slotted post-wall waveguide array with interdigital structure for 45/spl deg/ linear and dual polarization

This work proposes a dual-polarized planar antenna; two post-wall slotted waveguide arrays with orthogonal 45/spl deg/ linearly-polarized waves interdigitally share the aperture on a single layer substrate. Uniform excitation of the two-dimensional slot array is confirmed by experiment in the 25 GHz band. The isolation between two slot arrays is also investigated in terms of the relative displacement along the radiation waveguide axis in the interdigital structure. The isolation is 33.0 dB when the relative shift of slot position between the two arrays is -0.5/spl lambda//sub g/, while it is only 12.8 dB when there is no shift. The cross-polarization level in the far field is -25.2 dB for a -0.5/spl lambda//sub g/ shift, which is almost equal to that of the isolated single polarization array. It is degraded down to -9.6 dB when there is no shift.     

The role of prostate specific antigen in diagnosis of localized adenocarcinoma of the prostate. Nara Uro-Oncology Research Group

The number of cases of prostate carcinoma (PCA) is steadily inceasing in Japan. The clinical application of a reliable tumor marker, prostate specific antigen (PSA) for the diagnosis, as well as the increasing elderly population in Japan may account for this increase. The subjects were patients at the Nara Medical University and its affiliated hospitals; 1) 687 cases without PCA were evaluated for age-specific PSA and the incidence of abnormal PSA following urological manipulations, 2) 135 cases with histological proven BPH by transurethral resection of prostate (TUR-P) were examined for PSA density (PSAD) and positive PSA rate in BPH, 3) 135 cases receiving a needle biopsy with suspicion of PCA were examined for the efficacy of PSA and PSAD and other parameters, and 4) 459 PCA cases treated between 1988 and 1994, were examined for specific PSA and PSAD values by stage and degree of cell differentiation. The PSA assay used in this study was MARKIT-M PA (normal range < or = 3.6 ng/ml). The PSA was decreased gradually with age in non-PCA patients, and abnormal PSA was found in 5.5% of these patients following manipulations. The average PSA was 2.95 +/- 2.03 ng/ml in 130 BPH patients (mean age: 71.1 +/- 7.0 years old. and average prostate volume: 32.9 +/- 16.1 ml). And abnormal PSA level (more than 3.61 ng/ml) was found in 22.3%. The mean PSAD was 0.1.0 +/- 0.06, and PSAD was below 0.15 in 86.1% of these BPH cases. Among the 135 cases receiving a needle biopsy, 33 cases had PSA values between 3.61 and 10.0 ng/ml. Of these cases, PCA was found in 18.5% of the 27 cases with a PSAD below 1.5, and in 33.3% of the 6 cases with a PSAD over 1.5. PSA and PSAD were proportionally increased with stage, and a significant difference in the PSA value was observed between stage B1 and B2, and stage C and D (P < 0.05). However, PSA and PSAD values were not significantly correlated with the cell differentiation in PCA stage A2-C. In total, PSA was 18.1 ng/ml in well, 23.9 ng/ml in moderately and 35.9 ng/ml in poorly differentiated type PCA. The positive rate of PSA was 22.3, 65.4 and 83.5%, that of prostate acid phosphatase (PAP) was 10.0, 17.8 and 45.8%, and that of GSM was 25.0, 14.7 and 68.4%, in BPH, stage A PCA and stage BPCA, respectively. In conclusion, PSA is the most reliable tool in the diagnosis of localized PCA. However, the differential diagnosis of BPH and localized PCA is difficult when the PSA value is between 3.61 and 10.0 ng/ml, and accurate staging of localized PCA is difficult with PSA or PSAD alone. At present, it is necessary to use all possible tools for the early detection of localized PCA, and to perform the needle biopsy in all PCA-suspicious cases.     

Adaptive covariate acquisition for minimizing total cost of classification

Machine Learning - In some applications, acquiring covariates comes at a cost which is not negligible. For example in the medical domain, in order to classify whether a patient has diabetes or not,...     

EDM-Lathe for Micromachining

In this paper a new type of micro-EDM machine is proposed. The machine operates similarly to a turning lathe. An electrode fabrication system is installed which makes it possible to fabricate on-the-machine complex microelectrodes with sharp edges and corners. A prototype set of equipment was realized and test machining proved that a machine of this type can produce microcylindrical, overhung cavities, or cylindrical microholes with larger internal diameters than the entrance diameter. This result reveals the possibility of fabrication of various microparts such as microball bearings.     

Studies on biaxial stretching of polypropylene film. IX. Melting behavior of biaxially stretched film in one step

Melting temperature of a film biaxially stretched in one step in air at 152 or 140°C increases with increase of vA, whereas heat of fusion and density decrease with increase of vA, where vA is the degree of stretching in area. The rapid decrease in density occurs for vA > 10. Extrapolation of the plot of the density versus vA^?1/2 gives a value of 0.870 g/cm³ at infinite vA, which has been reported as the amorphous density of isotactic polypropylene by Farrow. This is so because the fine structure of the film becomes more and more amorphous with further stretching and reaches completely amorphous state at infinite vA. The temperature of stretching has a strong effect on the thermal behavior of a film; a low stretching temperature (140°C) brings about lower melting temperature, heat of fusion, and density. Crystallinity after melt press has not so large an effect on the melting behavior as the stretching temperature. Melting temperature and the shape of the thermogram also depend on the heating rate. There is an appropriate heating rate depending on vA which gives the minimum melting temperature. With stretched samples, a small side peak or a shoulder appears at a relatively low temperature in the thermogram when a high heating rate is used.     

Synthesis of polyoxyethylene derivatives of diesters of sucrose with long-chain fatty acids

Summary Since the long-chain fatty acid sucrose diesters inevitably produced in the synthesis of monoesters are only slightly soluble in water, no important use can be found for them at the present time except as oilsoluble emulsifying agents. In order to exploit new uses we have attempted to improve their solubility in water by introducing oxyethylene radicals into the molecule. The addition reaction of ethylene oxide with the sucrose diesters was carried out in an autoclave in the presence of alkaline catalysts. With the reaction temperature maintained between 100–130° the pressure decreased as the reaction proceeded, and one to two hours were required to consume the ethylene oxide used. The addition products are yellow or orange oily materials soluble in water. Aqueous solutions showed good surface-active properties.     

Studies on sublimation of disperse dye out of dyed polymers. I. Rate of sublimation and amorphous transition points of poly(ethylene terephthalate)

Four samples of poly(ethylene terephthalate) film of various crystallinities and orientation were dyed with p-nitroaniline and disperse dyes. When these films were heated under a 2–3 × 10^?3 mm Hg vacuum at a specified temperature T, the dye sublimed out of the dyed specimen. The amount (M_t/M_∞) of sublimed dye is in linear proportion to the square root of the sublimation time, t^½, where M_t and M_∞ are the amounts of dye sublimed for times t and t = ∞. The diffusion coefficient D, calculated from the slope of the above plot, is independent of the dye concentration of the film. When log D is plotted against 1/T°K over the temperature range 320–520°K, the relation is composed of two to four intersecting lines with the slope decreasing with elevation of temperature and with the breaks at about 89°–98°, 122°–135°, 155° and 175°–176°C. These breaks are the amorphous transitions: the first is the glass transition temperature T_g, the second and the fourth are the amorphous transitions corresponding to the crystalline transition points, i.e., the cold crystallization temperature and the smectic–triclinic transition temperature. With some exceptions, these amorphous transitions are found also by dilatometry and electrical conductivity measurements. The apparent activation energy for diffusion decreases from about 100 kcal/mole for the glass state to 22–24 kcal/mole for the region above 180°C. The activation energy for each region changes slightly with the size of dye molecule and the crystallinity and orientation of the film.     

Capacitance behavior of activated carbon fibers with oxygen-plasma treatment

Modified activated carbon fibers (ACFs) were used as the electrodes of an electric double-layer capacitor and showed an enhanced capacitance effect after a RF-plasma treatment. The capacitance and the surface functional groups of the ACFs were studied. For the plasma-treated ACFs having a specific surface area of 1500 m² g⁻¹, the capacitance increased by 28% compared to the untreated sample and the highest electric capacitance value of 142 F g⁻¹ was achieved with an oxygen feed concentration of 10 vol.%. The Brunauer-Emmett-Teller (BET) surface area was 2103 m² g⁻¹, which was 34% higher than that of the untreated sample. The pore volume was similarly increased to 483.1 cm³ g⁻¹ STP, and from the pore distribution plot, quantities of mesopores of 10 nm or less and micropores also increased. However, in order to enhance the capacitance, the quinone functional group had a significant influence in addition to the BET surface area. The correlation between the capacitance and the number of quinone functional groups was confirmed because quinone is an electron acceptor.     

Evaluation for the curing characteristics of phenolic molding compounds by rockwell hardness test at an elevated temperature

Rockwell hardness measurement at an elevated temperature has been proposed as an evaluation method for the curing characteristics of thermosetting molding compounds. This method is convenient and has a high accuracy over a wide range of curing, Using a cone indenter, the following advantages are brought about: a good correspondence with acetone extraction test, in showing the degree of cure of the internal part of a molding rather than that of the skin layer, and a higher sensitivity in measuring higher degrees of cure. On examining curing behavior of commercial phenolic molding compounds by this method, an inflection point was observed on a plot of the hardness vs log curing time. This critical point has been called “the minimum cure time”, beyond which the molding exhibits good physical properties.