Preparation of Aluminum Nitride Powder from Aluminum Polynuclear Complexes

AIN powder was synthesized from aluminum polynuclear complexes. Basic aluminum chloride and basic aluminum lactate were used as the aluminum polynuclear complexes. These starting materials and glucose were dissolved in water and mixed homogeneously. AIN powder was obtained by calcining after drying and precalcining at 800°C under nitrogen gas flow. Then excess carbon was removed by firing in air. Nitridation in the system was investigated and compared with that in the alumina–carbon black system. It was found that in our reaction system nitridation began and proceeded at lower calcination temperatures above 1200°C than in the alumina–carbon black system. Using aluminum polynuclear complexes, AIN was synthesized through the nitridation of γ-alumina and produced in a very fine and sharp particle size distribution.     

All-solid-state, high-power, deep-UV laser system based on cascaded sum-frequency mixing in CsLiB6O10 crystals

We report on an efficient use of CsLiB(6)O(10) (CLBO) crystals employed for an all-solid-state deep-UV laser system operated at 5 kHz. We obtained greater than 3 W of UV radiation around 242 nm by mixing the 349-nm third harmonic of a Nd:YLF laser with the tunable output from a Ti:sapphire laser in a CLBO crystal. This UV radiation was subsequently mixed with the residual 1047-nm output from the Nd:YLF laser in a second CLBO crystal. The system produced 1.5 W of deep-UV radiation at 196.3 nm, which is, to our knowledge, the highest deep-UV power below 200 nm generated in a nonlinear optical crystal. Additionally, the bandwidth of both outputs was estimated to be less than 200 MHz.     

MgATP-induced conformational changes in a single myosin molecule observed by atomic force microscopy: periodicity of substructures in myosin rods

This paper discusses the conformational changes in a single myosin molecule directly observed using atomic force microscopy (AFM). The myosin molecules were pretreated in rigor solutions without MgATP or in relaxed solutions with various concentrations of MgATP. The images of these molecules were obtained using a tapping mode AFM. The results indicate that the orientation of the myosin's heads and tail strongly depend on the MgATP concentration. Without using MgATP, almost all of the myosin molecules are in the extended form; however, when MgATP is used, the molecules bend according to the level of MgATP concentration. The mean-square end-to-end distance of the myosin molecules is significantly shorter with p[MgATP] = 4 than with p[MgATP] = 6. The rod region did not show the same level of intensity along their length in the extended form. The rods exhibited clusters of discontinuity, which were identified as substructures. The size of these substructures change at intervals that are multiples of 14.3-14.5 nm, which reflects the periodicity of the alpha-helical coiled coils. The substructure clusters also correspond to the myosin crossbridge spacing in muscles (14.3 or 43 nm). These results suggest that the myosin's head bends in conjunction with the bending or tilting in the helical substructures. Conformational changes of the myosin molecule induced by MgATP seem to mimic the molecular motions in a muscle's force generation process.     

Wide-wavelength tunable lasers with 100 ghz fsr ring resonators

A widely tunable laser, consisting of a 100 GHz FSR triple-ring resonator and a semiconductor optical amplifier, is presented. The 100 GHz FSR ring resonator makes it possible to demonstrate 96 nm wavelength tuning with stable single-mode operation produced by a large threshold gain difference     

Transmission electron microscopic observations of the decomposition process of lithium alanate

The thermal decomposition process of lithium alanate (LiAlH₄) was investigated by TEM, TG-DTA and XRD. It was shown that LiAlH₄ decomposes through a two-step reaction: a liquid-to-solid phase transition in the first step of the decomposition and a solid-to-solid reaction in the second step of the decomposition, both steps accompanied by hydrogen release. The particle size of the aluminum (Al), which formed in the first decomposition step, was much larger than that in the second decomposition step. In addition, Al particles formed in the liquid phase of LiAlH₄ in the first decomposition step, while, they form in solid phase of Li₃AlH₆ in the second decomposition step, resulting in the kinetics of the first decomposition step being faster than that of the second decomposition step. The investigation clearly demonstrated the reaction model of the decomposition of LiAlH₄ in the nano-scale, showing different diffusion processes of Al in each of the decomposition steps.     

Variable temperature neutron diffraction studies of single crystals of LiND2

We have synthesized a single crystal of lithium amide (LiNH₂, LiND₂) by melting method, and performed neutron diffraction of the single crystal at variable temperature. LiND₂ is tetragonal structure and I-4 space group. Lattice parameters and unit cell volume of LiND₂ at room temperature, 50 °C, 100 °C, 150 °C and 200 °C were determined. Both of the lattice parameters and the unit cell volume increase with increase of temperature. From these results, we have estimated coefficient of volumetric thermal expansion α_V of LiND₂ to be 222 × 10⁻⁶/K. With increase of temperature, all thermal ellipsoids gradually expand because of thermal vibration.     

Novel Fabrication of High-Quality ZrO2 Ceramic Thin Films from Aqueous Solution

We report on the direct deposition of high-quality ZrO₂ thin films on various kinds of substrates by the liquid phase deposition method. After reaction for 24 h, thin films formed on various kinds of substrates, and the obtained thin film was comprised of densely packed nano-sized particles. The film annealed at 500°C showed a tetragonal phase at room temperature and this phenomenon has been discussed from the viewpoint of crystallite size effect. The result of optical transmittance measurement revealed that high transparency, more than 70% transmittance, has been achieved for the film after annealing at 900°C.