Photocatalytic Property and Electronic Structure of Lanthanide-based Oxysulfides

Lanthanide-based oxysulfides and sulfide, LnTaO_3.5S_0.5, Ln₁₀OS₁₄ (Ln = La, Pr, Nd, Sm) and La₄In₅S₁₃, were successively synthesized by sulfurization in a flowing H₂S. The sulfurization decreased the band-gap energies from >4 eV to <3eV, because of the formation of occupied S3p orbitals on the top of valence band. In accordance with the small band gap, the H₂ evolution from a 0.01 M Na₂S and 0.01 M Na₂SO₃ solution system was observed under irradiation of light up to >500 nm. The rate of H₂ evolution under light irradiation of >500 nm increased in the order of Ni/LaTaO_3.5S_0.5 < Ru/La₁₀OS₁₄ < Pt/La₄In₅S₁₃.     

A 322 MHz random-cycle embedded DRAM with high-accuracy sensing and tuning

A 16 Mb embedded DRAM macro in a fully CMOS logic compatible 90 nm process with a low noise core architecture and a high-accuracy post-fabrication tuning scheme has been developed. Based on the proposed techniques, 61% improvement of the sensing accuracy is realized. Even with the smallest 5 fF/cell capacitance, a 322 MHz random-cycle access while 32 ms data retention time which contributes to save the data retention power down to 60 /spl mu/W are achieved.     

Automated camerawork for capturing desktop presentations

A novel automated camera control method for capturing desktop presentations is introduced. Typical features and the camerawork of shots that appear frequently in TV programs are discussed. To realise those features in this automated video capturing system, the purpose of camerawork is classified from two points of view: target and aspect-of-target. Then, the correspondence between the classification and typical shots and camerawork is considered. A virtual-frame control algorithm based on this idea is proposed, and its implementation in a video production system. Results are shown that verify this method through two kinds of experiments, virtual video capturing using CG animations and real video capturing of real presentations.     

Superconductivity in the tetragonal phase of La1.9Bi0.1CuO4+δ annealed under high oxygen pressure

We have investigated the relation between the crystal structure and superconductivity in La_1.9Bi_0.1CuO_4+δ , in which the phase separation observed in La₂CuO_4+δ is suppressed. A phase diagram in theT?δ plane is given for La_1.9Bi_0.1CuO_4+δ with excess oxygen. For very smallδ values, the crystal structure is orthorhombic, and an orthorhombic-tetragonal phase transition occurs markedly atδ ～ 0.03 in the measured temperature range between 13 and 293 K. Superconductivity is observed in the range of 0.04<δ<0.11. This is clear evidence thathigh-T _c superconductivity also appears in the tetragonal phase.     

Separation of di- and tripeptides with solvent extraction and an emulsion liquid membrane

The extraction equilibria of various di- and tripeptides with di-2-ethylhexylphosphoric acid (D2EHPA) were studied at low pH values. The complex extracted to organic phase consisted of one molecule of peptide and two molecules of D2EHPA dimer. The extraction constants of the peptides correlated well with the distribution coefficients of peptides between 1-octanol and water, which is a measure of hydrophobicity. The permeation rates of peptides through an emulsion liquid membrane were examined by using D2EHPA as a carrier, Span 80 as an emulsifier and kerosene as a diluent. The rates varied considerably with peptide type, depending upon the hydrophobicity.     

New balance ground relay for parallel four-circuit transmission lines

A 66-kV network generally is grounded through a neutral grounding resistor. In this network a single-phase ground-fault current is limited to as small as 100 to 400 A. There are parallel four-circuit transmission lines mounted on the same tower in the 66-kV network. In such transmission lines, the load and the fault currents could induce circulating current that flows through the lines. Since the circulating current has zero-phase-sequence and negative-phase-sequence components, it could cause unwanted operation of a balance ground relay using zero-phase-sequence current. However, it is difficult to compensate for the circulating current by the conventional vector compensation scheme. This paper presents a new balance ground relay to deal with the circulating current. In the relay from the ground-fault inception until first tripping, the difference current Δ3I_2d of negative-phase-sequence current 3I_2d of the differential current between two protected lines is used as an input current. The Δ3I_2d is the difference current of 3I_2d between, before and during faults. After the first tripping, the difference current of positive-phase-sequence load current and zero-phase-sequence current of the forementioned differential current are used as an input current. Consequently, a higher sensitivity of the ground-fault protection for these lines has been achieved. The correct operation of the new balance ground relay was confirmed when a single-phase-ground-fault occurred in the parallel four-circuit transmission lines, to which the relay is applied.     

Optimal production-inventory policy for make-to-order versus make-to-stock based on the M/Er/1 queuing model

This paper analyzes a multi-product production / inventory system where demands for each item arrive according to a Poisson process and the production time for each product has an Erlang distribution. The paper proposes an optimality condition that specifies whether each product should be produced make-to-stock or make-to-order. In the event a product should be produced make-to-stock, an approach for computing the optimal base-stock level is proposed. Numerical examples are given for illustrative purpose.     

Regenerating-mode low-speed operation of sensorless induction motor drive with adaptive observer

Speed estimation methods for sensorless induction motor drives can be divided into two groups. One is based on information about fundamental components of stator currents and voltages. The other is based on high-frequency components injection in stator voltages or currents. The latter may operate stably under zero frequency, which occurs in regenerating mode at low speeds. It, however, causes loss increasing and torque ripple. The former is difficult to operate under zero frequency. The authors propose a stable method categorized in the former group even in regenerating mode at low speeds. The proposed method is based on an adaptive flux observer. First, a new observer gain design is shown. Next, a method avoiding zero-frequency operation with controlling a rotor flux level is proposed.