Multilayer power printed structures suitable for controlling EMI noises generated in power converters

Electromagnetic interference (EMI) noises generated in power converters are diffused on the surface of conductors. This means influences occur from radiated EMI noises emitted from power transmission lines as well as conducted EMI noises transmitted from them. EMI noises diffusing on the surface of conductors are generally difficult to control using conventional concentrated constant theory. Thus, a new approach based on distributed constant circuit theory is needed in order to control EMI noises. A power converter structure to control EMI noises using multilayer power printed circuit technology is studied in this paper. A structure which can control EMI noises should simultaneously satisfy two conditions, i.e., one to shut down and one to attenuate EMI noises. The structure satisfying these conditions is studied through simulations using the Transmission-Line Modeling Method. The simulations show that the diffusion of EMI noises is controlled by dividing the flow of currents produced by EMI noises into the horizontal and perpendicular directions. That is, the horizontal current flow is controlled inside using the differences in the resistance produced from differences between inner and outer diameter of power transmission lines and the perpendicular current flow can be controlled by properly designing the thickness of the dielectric layer sandwiched between P-and N-power transmission lines with the symmetrical structure. Moreover, it is confirmed by simulations and experiments that the attenuation of EMI noises is affected by the width of the power transmission lines. It is expected that the results obtained in this paper can provide important rules when designing power converters with EMI noise control functions which use the multilayer power printed circuit technology.     

Right atrial contractile performance in patients with myocardial infarction

To evaluate right atrial (RA) contractile performance in patients with myocardial infarction, we validated a cineangiographic method of RA volume measurement, and investigated RA volume change in 'normal' individuals and patients with a previous myocardial infarction. Sixteen silicone rubber RA casts made from human cadavers were filmed in the postero-anterior and left lateral projections. The cast volumes calculated following Simpson's rule were in good agreement with those measured by water replacement (r = 0.992, P < 0.01). At cardiac catheterization, biplane RA cineangiography was performed in 19 'normal' individuals (N group), in 14 patients with a previous antero-septal infarction (AMI group) and in seven patients with a previous inferior infarction (IMI group). The RA volume-time curve was constructed at 20-40 ms intervals for one cardiac cycle. RA volume at the beginning of the atrial contraction (RAVd), which was defined as the 'preload' of the RA, tended to be larger in both the AMI and IMI groups compared with 'normal' individuals. The RA ejection volume was significantly larger in both the AMI (18.4 +/- 2.1 ml.m-2, P < 0.01) and IMI groups (19.4 +/- 2.8, P < 0.01) than in the N group (14.5 +/- 1.9), even for a comparable level of RAVd (range from 26 to 36 ml.m-2) (18.6 +/- 2.1, P < 0.01, 18.2 +/- 2.0, P < 0.01, 14.7 +/- 1.9, respectively). These results suggest that RA contraction increases in patients with myocardial infarction by increasing both the 'preload' and 'contractility' of the RA.     

Effect of ibudilast on microcirculation thrombosis in rat inner ear

Arterial wall thickening may be quantitatively assessed by measuring the intima-media thickness (IMT) with high resolution ultrasound. Previous studies have shown a good inter/intraobserver variability of IMT measurements in the common carotid. In this study we evaluated the inter/intraobserver variability of IMT measurements in 10 randomly selected asymptomatic subjects (age 55.4 +/- 6). Two carotids and two femorals were studied in each subject. IMT for each patient was the average of five IMT measurements at the artery bifurcation. Three observers repeated the scanning and the measurements twice with no knowledge of the previous readings. The between observer coefficient of variation (CV) was 8.45%; the intraobserver CV (mean of carotids and femorals) varied from 4.4 to 5.1% for the three observers who measured IMT three times. The mean absolute difference between the first and the third measurement was 0.0738 mm. In conclusion IMT measurement variability is mostly due to differences between observers. The intraobserver variability is very small. IMT measurements at the carotid and femoral bifurcations have a low variability and are a good expression of atherosclerosis as they consider early lesions at the bifurcation level which may not be observed in the common carotid.     

Hybrid Link/Path-Based Design for Translucent Photonic Network Dimensioning

The advancement of ultralong-haul transmission technology has dramatically enhanced the all-optical reaches. However, the actual situations of installed fiber and sites for terrestrial network often prevent implementing a purely transparent network, and thus, opaque reshaping retiming regenerating (3R) regeneration is required to guarantee optical signal reachability. Since 3R regenerators based on optical/electrical/optical conversion tend to dominate the total network costs, an efficient network design method that allocates a minimum number of 3R regenerators to optimum locations is essential to build a cost-effective photonic network. In this paper, we propose such a network-dimensioning method by combining the advantages of link-based and path-based design approaches. It first guarantees optical signal reachability for any possible traffic demand in each segmented linear link. After combining all the links, excessive regenerators are eliminated based on the optical signal quality check with -factor calculation for each wavelength path. A trial design of a large-scale mesh network demonstrated a significant cost savings of more than 30% in comparison with a conventional link-based design. In the trial, the impact of fiber loss coefficient over the total network cost was investigated quantitatively, addressing the importance of such quantitative modeling and analysis.     

Air bubbles in the subclavian or internal jugular veins: a common finding on contrast-enhanced CT

BACKGROUND: Foot complications in diabetes incur huge human and medical costs. There is a high incidence of complicated diabetes mellitus in Far North Queensland, particularly in the indigenous communities. METHODS: An audit of 51 patients admitted to Cairns Base Hospital from July 1992 to December 1994 with diabetic foot complications requiring surgical intervention was performed. RESULTS: The majority of surgical procedures were for serious infections in neuropathic feet precipitated by minor trauma. Surgical procedures included debridement/drainage, minor amputation, major amputation and arterial bypass. Half of the patients required more than one procedure and/or multiple admissions. Average length of stay was 48 days. Indigenous patients were overrepresented in this audited group. CONCLUSIONS: Prevention or minimization of diabetic foot complications can be achieved only through improvement in education and vigilance at all levels of the treatment process from community to hospital. Special attention to the needs of indigenous communities with a high incidence of diabetes must be a feature of any future initiatives.     

Fractionation and enrichment of CLA isomers by selective esterification with Candida rugosa lipase

A commercial product of CLA contains almost equal amounts of cis-9,trans-11 (c9,t11)-CLA and trans-10,cis-12 (t10,c12)-CLA. We attempted to enrich the two isomers by a two-step selective esterification using Candida rugosa lipase that acted on c9,t11-CLA more strongly than on t10,c12-CLA. An FFA mixture containing CLA isomers was esterified with an equimolar amount of lauryl alcohol in a mixture of 20% water and the lipase. When the esterification of total FA reached 50%, two isomers were fractionated in a good yield: t10,c12-CLA was enriched in FFA, and c9,t11-CLA was recovered in lauryl esters. The FFA were esterified again to enrich t10,c12-CLA. At 27.3% esterification of total FA, the t10,c12-CLA content in FFA increased to 64.8 wt% with 89.3% recovery: The ratio of the content of t10,c12-CLA to that of two isomers was 95.9%. Lauryl esters obtained by the single esterification were employed for enrichment of c9,t11-CLA. After the esters were hydrolyzed, the resulting FFA were esterified again with lauryl alcohol. At 62.0% esterification of total FA, the c9,t11-CLA content in lauryl esters increased to 73.3 wt% with 79.4% recovery: The ratio of the content of c9,t11-CLA to that of two isomers was 95.6%. In a 600-g-scale purification, molecular distillation was effective in separating the reaction mixture into lauryl alcohol, FFA, and lauryl ester fractions.     

Anionic polymerization of styrene in 2-methyltetrahydrofuran: temperature dependence of the field effect

Kinetics of living anionic polymerizations of styrene was investigated for lithium, sodium, and potassium salts in 2-methyltetrahydrofuran at 35, 25, 0, and ?70°C in the presence and absence of a high intensity electric field. At 35 and 25°C, a field acceleration effect was observed whereas no effect was found at 0 and ?70°C. The propagation rate constant of ion pairs was almost independent of gegen ions and their temperature dependence was smaller than that of free anions. The free ions seem to be more strongly solvated as the temperature decreases.