Efficient Excitation of Hybrid Modes in a THz Clinotron

Journal of Infrared, Millimeter, and Terahertz Waves - Various regimes of hybrid, bulk-surface, modes being excited in the clinotron oscillator with a sheet electron beam and nonuniform grating...     

Fabrication of lotus-type porous carbon steel by the continuous zone melting method and its mechanical properties

A lotus-type porous carbon steel with cylindrical pores was fabricated by the continuous zone melting method in a pressurized mixture of hydrogen and helium gases. The porosity increases with increasing partial pressure of the hydrogen gas, while the pore diameter remains almost constant, independent of the pressure. The ultimate tensile strength of the specimen with cylindrical pores parallel to the tensile direction is lower than the estimated value, assuming that the strength is decreased in proportion to the decrease of the cross-sectional area of the specimen, while the yield strength is higher than the estimated value. The compressive yield strength is also higher than the estimated value. The increase in yield strength is considered to be due to precipitation strengthening. The tensile strength is increased by quenching and tempering, while the elongation decreases. Such mechanical properties are discussed in terms of the microstructural analysis.     

Up- and down-regulation of calpain inhibitor polypeptide, calpastatin, in postischemic hippocampus

A dental student developed swelling of the lips and peri-oral urticaria, immediately after placement of a dental rubber dam during a chairside demonstration of clinical dentistry. A provisional diagnosis of a Type I hypersensitivity reaction to natural rubber latex was made and an appointment organised for specialist investigations. The student reported an atopic history and allergy to peanuts. A Radioallergosorbent Test (RAST), to measure Ig-E antibodies to latex, was positive. The dental student was given advice concerning the avoidance of natural rubber latex. Dental staff must be aware of potentially serious reactions to natural rubber latex in the dental surgery.     

An innovative semianalytical technique for ceramic evaluation at microwave frequencies

We have developed an innovative semianalytical technique for various substrate material characterization. The developed technique is a measurement procedure and data-reduction formulation that takes into consideration the radiation loss in a resonant structure, allowing for a more effective means of dielectric- and conductor-loss determination for a microstrip ring resonator and its substrate material. We separate dielectric and conductor loss precisely, evaluate the contribution of each term in the overall loss performance, and analytically predict the error in their respective predicted value.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Feedback control of decoupled bending and torsional vibrations of flexible beams

In this article, we consider a flexible beam with a rigid body, of which the bending vibration and the torsional vibration are decoupled. Therefore we need two control motors to suppress the vibrations. Each set of dynamic equations is treated in the form of an appropriate Hilbert space. A stabilizing feedback control law of each rotation motor will be established on the basis of modal analysis. A set of experiments has been carried out, and the results demonstrate the effectiveness of the dynamic model and the proposed control law. © 1994 John Wiley & Sons, Inc.     

High-efficiency finishing process for metal mold by large-area electron beam irradiation

A new finishing process for metal molds by large-area electron beam (EB) irradiation is proposed in this study. In the large-area EB irradiation equipment used here, an EB with high-energy density is irradiated without focusing the beam, and so the EB with a maximum diameter of 60 mm can be used for melting or evaporating metal surface instantly. Experimental results show that the surface roughness decreases from 6 μmRz to less than 1 μmRz in just a few minutes under proper machining conditions. The corrosion resistance of metal mold surface also could be greatly improved by large-area EB irradiation. Furthermore, the surface roughness of tilting surface close to 90° could be well improved. Therefore, large-area EB irradiation method has a possibility to become a high-efficiency finishing process for metal molds.     

Dispersion compensation with SBS-suppressed fibre phase conjugator using synchronised phase modulation

204 km, 10 Gbit/s standard optical fibre transmission is successfully demonstrated using the mid-span spectral inversion technique with a stimulated Brillouin scattering suppressed fibre phase conjugator, proposed recently by Tani and Yamashita. Transmission performance has been improved compared with a conventional phase conjugator.     

A novel method of suppressing the inrush current of transformers by using a series‐connected voltage‐source PWM converter

This paper proposes a novel method of suppressing the inrush current of transformers. A small‐rated voltage‐source PWM converter is connected in series to the transformers through a matching transformer. As the connected PWM converter serves as a resistor for the source current, no inrush phenomena occurs. The required rating of the PWM converter, which serves as the damping resistor for the inrush phenomena, is 1/400 that of the main transformers in single‐phase circuits. In three‐phase circuits, it is 1/900. The basic principle of the proposed method is discussed. Digital computer simulation is implemented to confirm the validity and excellent practicability of the proposed method using the PSCAD/EMTDC. A prototype experimental model is constructed and tested. The experimental results demonstrate that the proposed method can perfectly suppress the inrush phenomena. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 157(4): 56–65, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20174     

Optical data storage by novel photoelectrochromic polymer

A novel elastic polymer containing 4,4′-bipyridinium salts with tetrakis[3,5-bis(trifluoromethyl)phenyl]borate as part of the main chain was synthesized. The cast film showed persistent and reversible colour changes due to photoinduced electron transfer upon excitation of an ion-pair charge-transfer band (_ex >365 nm) in vacuo. The lifetime of the coloured state markedly depended on temperature. The optically written data were stored without decay below 0°C and were erased thermally at elevated temperatures. The colour changes were reversibly repeatable for many times.