Fabrication of lotus-type porous carbon steel by the continuous zone melting method and its mechanical properties

A lotus-type porous carbon steel with cylindrical pores was fabricated by the continuous zone melting method in a pressurized mixture of hydrogen and helium gases. The porosity increases with increasing partial pressure of the hydrogen gas, while the pore diameter remains almost constant, independent of the pressure. The ultimate tensile strength of the specimen with cylindrical pores parallel to the tensile direction is lower than the estimated value, assuming that the strength is decreased in proportion to the decrease of the cross-sectional area of the specimen, while the yield strength is higher than the estimated value. The compressive yield strength is also higher than the estimated value. The increase in yield strength is considered to be due to precipitation strengthening. The tensile strength is increased by quenching and tempering, while the elongation decreases. Such mechanical properties are discussed in terms of the microstructural analysis.     

AFM observation of polyethylene single crystals: selective handedness of screw dislocations in a chair type

The three-dimensional morphology of polyethylene single crystals grown from dilute solution has been examined by atomic force microscopy. Single crystals were deposited on a soft ground of aqueous solution of poly(vinyl alcohol) (PVA) to avoid the collapse of thin lamellar crystals with thickness of 10 nm. The observation of single crystals on dried PVA clarifies the morphology of a chair type crystal as well as well-known hollow pyramidal type. It has been confirmed that the screw dislocations in the chair type follow a selection rule of the handedness in a manner to relieve the distortion in the chair type.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Lateral habits ofn-alkane single crystals

The lateral crystal habits ofn-alkanes (n-C _n H_2n+2) have been observed just below the melting points by optical microscopy forn=18, 19, 20, 22, 24, 34, 44, 50 and 65. The shape of the crystals depends on the crystal phase: circular in the rotator phase, lenticular in phase C, and diamond in the low-temperature phase. The rounding of the lateral shape can be explained in terms of thermal roughening of the lateral faces in the disordered phases at high temperature.     

Feedback control of decoupled bending and torsional vibrations of flexible beams

In this article, we consider a flexible beam with a rigid body, of which the bending vibration and the torsional vibration are decoupled. Therefore we need two control motors to suppress the vibrations. Each set of dynamic equations is treated in the form of an appropriate Hilbert space. A stabilizing feedback control law of each rotation motor will be established on the basis of modal analysis. A set of experiments has been carried out, and the results demonstrate the effectiveness of the dynamic model and the proposed control law. © 1994 John Wiley & Sons, Inc.     

High-efficiency finishing process for metal mold by large-area electron beam irradiation

A new finishing process for metal molds by large-area electron beam (EB) irradiation is proposed in this study. In the large-area EB irradiation equipment used here, an EB with high-energy density is irradiated without focusing the beam, and so the EB with a maximum diameter of 60 mm can be used for melting or evaporating metal surface instantly. Experimental results show that the surface roughness decreases from 6 μmRz to less than 1 μmRz in just a few minutes under proper machining conditions. The corrosion resistance of metal mold surface also could be greatly improved by large-area EB irradiation. Furthermore, the surface roughness of tilting surface close to 90° could be well improved. Therefore, large-area EB irradiation method has a possibility to become a high-efficiency finishing process for metal molds.     

Integrated-optic device for a fibre laser Doppler velocimeter

We first demonstrate an integrated-optic device for a fibre laser Doppler velocimeter, which consists of a waveguide interferometer and a frequency shifter in z-propagation Ti-diffused LiNbO3. The device is also pigtailed with a single-mode fibre to pick up a Doppler-shifted signal. Using the fabricated device, the velocity of a moving object was successfully heterodyne-detected with a signal/noise ratio of 30dB.     

A novel therapeutic approach for rectal varices: a case report of rectal varices treated with double balloon-occluded embolotherapy

We present a patient with continuous melena, diagnosed as rectal varices bleeding. She had a history of esophageal varices, which was treated by endoscopic ligation therapy. Eight years after the treatment of esophageal varices, the continuous melena began. Colonoscopic examination showed that the melena was caused by rectal varices, which were so severe that they could not be treated by either endoscopic sclerotherapy or surgical devascularization. Taking into considering the overall risk of treating rectal varices, we chose the approach of double balloon-occluded embolotherapy (DBOE) with 5% ethanolamine oleate with iopamodol as a liquid embolic material. DBOE is one of the interventional radiology techniques (Morita et al., Acta Hepatol Jpn 1994;35:109-120), but in this case was a completely new and novel clinical procedure for rectal varices. After the DBOE therapy, the condition of rectal varices was markedly improved. Thus, DBOE might be a new tool for treating inoperable rectal varices.     

A novel method of suppressing the inrush current of transformers by using a series‐connected voltage‐source PWM converter

This paper proposes a novel method of suppressing the inrush current of transformers. A small‐rated voltage‐source PWM converter is connected in series to the transformers through a matching transformer. As the connected PWM converter serves as a resistor for the source current, no inrush phenomena occurs. The required rating of the PWM converter, which serves as the damping resistor for the inrush phenomena, is 1/400 that of the main transformers in single‐phase circuits. In three‐phase circuits, it is 1/900. The basic principle of the proposed method is discussed. Digital computer simulation is implemented to confirm the validity and excellent practicability of the proposed method using the PSCAD/EMTDC. A prototype experimental model is constructed and tested. The experimental results demonstrate that the proposed method can perfectly suppress the inrush phenomena. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 157(4): 56–65, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20174