Surface Pretreatments of Silicon Nitride for CVD Diamond Deposition

The efficiency of different surface pretreatments (four standard chemical etchings and four diamond powder abrasive procedures) on silicon nitride (Si₃N₄) substrates for chemical vapor deposition (CVD) of diamond has been systematically investigated. Blank Si₃N₄ samples were polished with colloidal silica (∼0.25 μm). Diamond nucleation and growth runs were conducted in a microwave plasma chemical vapor deposition apparatus for 10 min and 6 h, respectively. Superior results concerning nucleation density ( N _d∼ 10¹⁰ cm⁻² after 10 min), film uniformity, and grain size (below 2 μm after 6 h) were obtained for the mechanically microflawed samples, revealing that chemical etchings (hot and cold strong acids, molten base or CF₄ plasma) are not crucial for good CVD diamond quality on Si₃N₄.     

Spectroscopic Multicomponent Analysis Using Multi-objective Optimization for Variable Selection

The multiple determination tasks of chemical properties are a classical problem in analytical chemistry. The major problem is concerned in to find the best subset of variables that better represents the compounds. These variables are obtained by a spectrophotometer device. This device measures hundreds of correlated variables related with physicocbemical properties and that can be used to estimate the component of interest. The problem is the selection of a subset of informative and uncorrelated variables that help the minimization of prediction error. Classical algorithms select a subset of variables for each compound considered. In this work we propose the use of the SPEA-II （strength Pareto evolutionary algorithm II）. We would like to show that the variable selection algorithm can selected just one subset used for multiple determinations using multiple linear regressions. For the case study is used wheat data obtained by NIR （near-infrared spectroscopy） spectrometry where the objective is the determination of a variable subgroup with information about E protein content （%）, test weight （Kg/HI）, WKT （wheat kernel texture） （%） and farinograph water absorption （%）. The results of traditional techniques of multivariate calibration as the SPA （successive projections algorithm）, PLS （partial least square） and mono-objective genetic algorithm are presents for comparisons. For NIR spectral analysis of protein concentration on wheat, the number of variables selected from 775 spectral variables was reduced for just 10 in the SPEA-II algorithm. The prediction error decreased from 0.2 in the classical methods to 0.09 in proposed approach, a reduction of 37%. The model using variables selected by SPEA-II had better prediction performance than classical algorithms and full-spectrum partial least-squares.     

Induction motor fault detection and diagnosis using a current state space pattern recognition

In the last few decades the continuous monitoring of complex dynamic systems has become an increasingly important issue across diverse engineering areas. This paper presents a pattern recognition based system that uses visual-based efficient invariants features for continuous monitoring of induction motors. The procedures presented here are based on the image identification of the 3-D current state space patterns that allow the identification of distinct fault types and, furthermore, their corresponding severity. This automatic fault detection system deals with time-variant electric currents and is based on the identification of three-phase stator currents specified patterns. Several simulation and experimental results are also presented in order to verify the effectiveness of the proposed methodology.     

Extraction and characterization of highly purified collagen from bovine pericardium for potential bioengineering applications

Bovine pericardium is widely used as a raw material in bioengineering as a source of collagen, a fundamental structural molecule. The physical, chemical, and biocompatibility characteristics of these natural fibers enable their broad use in several areas of the health sciences. For these applications, it is important to obtain collagen of the highest possible purity. The lack of a method to produce these pure biocompatible materials using simple and economically feasible techniques presents a major challenge to their production on an industrial scale. This study aimed to extract, purify, and characterize the type I collagen protein originating from bovine pericardium, considered to be an abundant tissue resource. The pericardium tissue was collected from male animals at slaughter age. Pieces of bovine pericardium were enzymatically digested, followed by a novel protocol developed for protein purification using ion-exchange chromatography. The material was extensively characterized by electrophoresis, scanning electron microscopy, energy dispersive X-ray spectroscopy, and infrared spectroscopy. The results showed a purified material with morphological properties and chemical functionalities compatible with type I collagen and similar to a highly purified commercial collagen. Thus, an innovative and relatively simple processing method was developed to extract and purify type I collagen from bovine tissue with potential applications as a biomaterial for regenerative tissue engineering.     

Partial replacement of EPDM by GTR in thermoplastic elastomers based on PP/EPDM: Effects on morphology and mechanical properties

The formulation of recycled thermoplastic elastomeric materials (TPE) based on ground tyre rubber (GTR), generated from end of life tyres, can be an alternative strategy to deal with a type of waste responsible for increasingly environmental problems over the past decades. The incompatibility of GTR with thermoplastics places several issues on the formulation of these materials, which this study tries to overcome. An encapsulation strategy of the GTR by an elastomeric phase is proposed in this work to overcome the lack of adhesion between the materials. Ternary blends, composed of a highly flowable polypropylene homopolymer, an ethylene propylene diene monomer (EPDM) and GTR were formulated and their morphology and mechanical properties analyzed. The morphology of the blends showed interaction between the materials, revealing that the encapsulation of GTR by a rubber phase can be an adequate strategy to formulate recycled‐based TPE materials, if the dimension of the GTR particles is controlled and taken into consideration. The mechanical properties revealed the replacement effect of EPDM by GTR, and its dependence on the amount of that replacement. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40160.     

Polyvinyl alcohol associated with carbon nanotube scaffolds for osteogenic differentiation of rat bone mesenchymal stem cells

Polyvinyl alcohol (PVAl) hydrogel, alone and reinforced with two types of carbon nanoparticles, was studied in cultured cells to assess its potential use in treating osteochondral defects. The carbon nanoparticles were produced by hot-filament chemical vapour deposition. The carbon material was characterised with a Renishaw Invia Raman microscope system and the morphological particles were characterised with field emission scanning electron microscopy and high-resolution transmission electron microscopy. Cytotoxicity was evaluated by measuring the Vero fibroblast-type cells’ metabolic activity and studying their morphology. The osteogenic differentiation of mesenchymal stem cells obtained from rat bone marrow was evaluated by alkaline phosphatase (ALP) and alizarin red S (ARS) staining. Cell viability and morphology were assessed with thiazolyl blue tetrazolium bromide and scanning electron microscopy, respectively. The materials did not interfere with the viability, metabolic activity, morphology and spreading of either of the cell types analysed. Nodules of mineralised organic matrix were identified with ARS and ALP, confirming osteogenic differentiation. These results indicated higher concentration of ALP and mineralised matrix for PVAl with carbon nanoparticles. The results of this study indicate the potential use of carbon nanoparticles with PVAl hydrogels as orthopaedic biomaterials to treat osteochondral defects, but further in vivo investigations are still necessary.     

High-voltage LDMOS transistors fully compatible with a deep-submicron 0.35 μm CMOS process

This work presents the design of LDMOS transistors fully compatible with a standard CMOS process, only requiring mask layout manipulation. A conventional 0.35 μm CMOS process was elected to demonstrate the viability of the approach. The prototyped LDMOS transistor exhibits a breakdown voltage of 24 V, which represents an improvement of 31% when compared with the high-voltage extended-drain NMOS available in the process library, while other static parameters remain in the same range. Furthermore, this solution enables the CMOS integration of a high-voltage pass-transistor, as a consequence of the formation of an isolated lightly doped p-type region inside the n-well.