Partial scan design and test sequence generation based on reduced scan shift method

This paper presents a partial scan algorithm, calledPARES (PartialscanAlgorithm based onREduced Scan shift), for designing partial scan circuits. PARES is based on the reduced scan shift that has been previously proposed for generating short test sequences for full scan circuits. In the reduced scan shift method, one determines proch FFs must be controlled and observed for each test vector. According to the results of similar analysis, PARES selects these FFs that must be controlled or observed for a large number of test vectors, as scanned FFs. Short test sequences are generated by reducing scan shift operations using a static test compaction method. To minimize the loss of fault coverage, the order of test vectors is so determined that the unscanned FFs are in the state required by the next test vector. If there are any faults undetected yet by a test sequence derived from the test vectors, then PARES uses a sequential circuit test generator to detect the faults. Experimental results for ISCAS'89 benchmark circuits are given to demonstrate the effectiveness of PARES.     

Complexity of the color appearance of objects with nonuniform illumination

An inversion relationship is clarified between lightness and brightness, and also between chroma and colorfulness under nonuniform illumination with different illuminance levels (high and low) within the same visual field. Brightness (or colorfulness) of object color with low lightness (or chroma) under high illuminance level is perceived higher than that of another object color with high lightness (or chroma) under low illuminance level. Two color images are given for showing the inversion phenomena on brightness–lightness and colorfulness–chroma between object colors under different illuminance levels. These color images are useful for making researchers on color understand the differences in concept between brightness and lightness, and also between colorfulness and chroma. In particular, the concept of colorfulness is important, but difficult to understand. © 2007 Wiley Periodicals, Inc. Col Res Appl, 32, 372–377, 2007     

Temperature Dependence of the Raman Spectrum in Lithium Oxide Single Crystal

Temperature dependence of the Raman spectrum of lithium oxide single crystal has been measured over a temperature range of 80 to 1073 K. The frequency shift and the line width of the Raman spectrum in lithium oxide were about 531 and 4.5 cm^-1 at 80 K, respectively. At 1073 K, the frequency shift and the line width attained the values of 464 and 112 cm^-1, respectively. The strong temperature dependence of the frequency shift and line width was compared with data from some crystals with a fluorite structure.     

Sintering of fibrous barium titanate powder compacts with preferred orientation

The sintering of fibrous BaTiO₃ powder particles was investigated. Special emphasis was given to the role of particle orientation in the compact on densification and microstructure development. Compacts were made by dry-pressing. During the initial stage of sintering, the fibrous particles rearranged and bundles of particles were formed. The volume of pores between bundles of particles decreased on further heating. Grain growth started when the sintered density reached ca. 56% of the theoretical density. Higher temperatures of sintering increased the degree of the crystal axis orientation. Thus, highly orientated sintered bodies with high densities were prepared by heating at 1500 °C.     

Thermal strain of high strength polyethylene fiber in low temperature

High strength polyethylene fiber (Toyobo, Dyneema® fiber: hereinafter abbreviated to DF) has a negative thermal expansion coefficient. Relation between fiber structure and thermal strain of DF used as reinforcement of DF reinforced plastic (DFRP) for cryogenic use was investigated. The crystallinities and orientation angles of several kinds of polyethylene fibers having different modulus from 15 to 134Gpa (herein after abbreviated to DFs) were measured by NMR and X‐ray. We obtained the parameters of the mechanical series‐parallel model composed of crystal and amorphous by crystallinity and modulus. Thermal expansion coefficients of DFs were estimated by mechanical series‐parallel model. All DFs having different modulus showed negative thermal expansion coefficients in the temperature range from 180 to 300K, and absolute values of those markedly increased by increasing tensile modulus of DF. The estimated thermal expansion coefficients showed negative values, and thermal strains showed a similar curve to observed ones mostly. Average thermal expansion coefficients in the temperature range from 180 to 300K estimated by mechanical model agreed with the observed ones. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2918–2925, 2004     

Aspects of gasification and structure in cokes from coals

Cokes were prepared from nine coals of different rank and characterized by surface area measurement, reactivity to carbon dioxide at 1473K and Raman-laser spectroscopy. Rates of gasification of cokes on a unit surlface area basis (K¹ = g m^?2 min^?1) decreased with increasing rank of parent coal based on maximum oil reflectances. However rates of gasification could not be related to coke structure as measured by Raman-laser spectroscopy.     

Two-stage pyrolysis of heavy oils. 3. Pyrolysis of tar-sand bitumens. Relation between ethylene yield and structural characteristics of heavy oils

Thermal cracking of tar-sand bitumens has been carried out using a two-stage pyrolysis reactor with temperature zones of 440°C and 750–800°C, respectively. Feedstocks were pyrolysed in the first stage into cracked oils, which were carried to the second stage for subsequent pyrolysis. Only 12–14 wt% of ethylene was obtained from tar-sand bitumens at the residence time of 1.2 s in the second stage, although 27 and 16 wt% were obtained from Taching and Iranian heavy vacuum residues, respectively. The tar-sand bitumens contain shorter paraffinic straight-chains and have more branched molecules than the vacuum residues of petroleum. A straight-chain paraffin index is proposed, with which a good correlation was obtained between ethylene yield and the fraction of straight-chain paraffin carbons in the heavy oil.     

Effect of Microstructural Control on Thermoelectric Properties of Hot-Pressed Aluminum-Doped Zinc Oxide

The thermal conductivity of polycrystalline Al-doped ZnO was controlled through the fabrication of nanostructured polycrystalline materials, by hot-pressing nanosized Zn_{1– x} Al _x O ( x = 0.01, 0.02) particles, which were synthesized by a coprecipitation and spray-drying method. This process resulted in an improved thermoelectric power factor because of the nanosized Zn_0.99Al_0.01O particles of the polycrystalline products. The thermal conductivity also was decreased as a result of the formation of nanocrystalline Zn_0.99Al_0.01O.     

Monodisperse nanoparticles of poly(ethylene glycol) macromers and N‐isopropyl acrylamide for biomedical applications

Poly(ethylene glycol)‐based nanoparticles have received significant attention in the field of biomedicine. When they are copolymerized with pH‐ or temperature‐sensitive comonomers, their small size allows them to respond very quickly to changes in the environment, including changes in the pH, ionic strength, and temperature. In addition, the high surface‐to‐volume ratio makes them highly functionalized. In this work, nanoparticles composed of temperature‐sensitive poly(N‐isopropylacrylamide), poly(ethylene glycol) 400 dimethacrylate, and poly(ethylene glycol) 1000 methacrylate were prepared by a thermally initiated, free‐radical dispersion polymerization method. The temperature‐responsive behavior of the hydrogel nanoparticles was characterized by the study of their particle size with photon correlation spectroscopy. The size of the nanoparticles varied from 200 to 1100 nm and was a strong function of the temperature of the system, from 5 to 40°C. The thermal, structural, and morphological characteristics were also investigated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1678–1684, 2003