Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

Studies on chitin. IX. Crosslinking of water-soluble chitin and evaluation of the products as adsorbents for cupric ion

Water-soluble chitin was successfully crosslinked to varying extents with glutaraldehyde in homogeneous aqueous solutions to improve the properties as an adsorbent for metal cations, and the effects of crosslinking were discussed. Complete insolubilization was achieved with the fivefold excess aldehyde, but, in terms of adsorptivity of Cu²⁺, the chitin crosslinked at an aldehyde/amino group ratio of 1.0 was found to exhibit remarkable capacity and was much superior to others. The desorption of Cu²⁺ from the adsorption complex was also attained effectively at pH 2.0. These results indicated that the loose crosslinking was quite simple and efficient to produce high capacity adsorbents for practical use. Thermal behavior of the crosslinked chitin was examined by TMA and TGA; a softening phenomenon was observed at 145°C.     

Synthesis of Heterocycle-Containing [60]Fullerene Derivatives. II.1 Recent Progress in [4 2]- and [3 2]-Cycloaddition Routes

Recent progress of synthesis of C₆₀ derivatives functionalized with hetero-cycles is reviewed, focusing attention on [4+2]- and [3+2] cycloaddition methodologies and oxidative heterocyclization.     

Basic fibroblast growth factor as one of the essential factors regulating lens transdifferentiation of pigmented epithelial cells

In vitro transdifferentiation of retinal pigmented epithelial cells of the chick embryo into lens cells can be markedly enhanced by culture in the presence of testicular hyaluronidase and phenylthiourea. Since the commercial preparations of hyaluronidase that had previously been used were very crude, a search for the actual effective molecule(s) enhancing lens transdifferentiation was conducted. First, we purified the enzyme and tested the effect of the purified hyaluronidase. Highly purified hyaluronidase itself did not enhance lens transdifferentiation. The crude hyaluronidase was then separated according to affinity with heparin, considering the possibility that the fibroblast growth factor (FGF) is contained in the crude hyaluronidase. Transdifferentiation-enhancing activity was detected in the fraction which was bound to heparin and eluted with 2 M NaCl, where no hyaluronate-degrading activity existed. Analysis of the fraction by SDS-PAGE revealed the existence of an 18 kDa protein whose NH2-terminal sequence was identical to that of basic FGF. The basic FGF derived from bovine brain also enhanced lens transdifferentiation of pigmented epithelial cells. These findings suggest that basic FGF must play a major role in enhancing transdifferentiation of pigmented epithelial cells to lens cells.     

Mechanical alloying in the Al-Bi alloy system

Mechanical alloying (MA) was carried out to investigate the MA behaviour of the immiscible Al-10, 30 at % Bi alloys. After the MA processing, the Al and Bi were finely and homogeneously alloyed. The Bi crystallite size decreased to 25 nm and 30 nm in the Al-10 at % Bi and Al-30 at % Bi alloys, respectively. By increasing the MA time, the hardness increased up to a value of 80 H _v, which is larger than that obtained from the rule of mixtures. The lattice parameter of Bi decreased by about 0.27%, which shows the formation of a non-equilibrium hcp Bi super-saturated solid solution. The extended solubility of Al in Bi was 1.9% in the Al-30 at % Bi alloy. Due to the extended solubility, depression of the melting temperature of hcp Bi was confirmed in the mechanically alloyed Al-Bi alloys. The maximum depression in the temperature was about 10 K. The measured values corresponded well with those estimated from the extrapolation of the solidus line.     

Cytokines and immune regulation in thyroid autoimmunity

We studied the role of cytokines and immune regulation in thyroid tissue from patients with Graves' disease. Immunohistochemistry showed that the thyroid glands are characterized by an aberrant expression of HLA class II antigens on thyrocytes, generation of new blood vessels and infiltration of mononuclear cells. We demonstrated that CD4+ memory cells were more frequent in thyroid glands from Graves' patients than were CD4+ naive cells. The intrathyroidal T cells demonstrated an enhanced expression of the adhesion molecules LFA-1, CD2, VLA-4 and VLA-5, and vascular endothelial cells of capillaries and thyrocytes in thyroid glands reacted with anti-ICAM-1 monoclonal antibody. The adhesion molecules and HLA antigens on both vascular endothelial cells and thyrocytes were regulated by inflammatory cytokines. These results suggest that circulating lymphocytes migrate into thyroid tissues and that memory T cells are retained in the thyroid tissues by cellular interactions with thyrocytes or with extracellular matrix.     

Recovery retardation in equal channel angular pressed Al–Zr alloy during friction stir welding

The effect of Zr on reduction of hardness and microstructure in an FS weld of equal channel angular-pressed Al alloy was investigated. Zr addition to Al suppressed dynamic recovery in the thermomechanically affected zone and enabled retention of the high hardness of the ECA-pressed material throughout the weld.     

An effect of microstructure on the interface resistance between a perovskite-type oxide electrode and yttria-stabilized zirconia

The electrode characteristics of perovskite-type oxides, La_0.6Sr_0.4CoO₃ and La_0.6Sr_0.4MnO₃, on ceria-based oxide and stabilized zirconia were analysed by the a.c. impedance method. The ionic conductivities of the electrolyte and electrode conductivities from the a.c. impedance analysis agreed with those obtained from the current interruption and d.c. four-probe methods. Two semicircles from the charge transfer and diffusion processes appeared as the electrode resistance. The relative contribution of these two processes to the overall electrode resistance strongly depended on the microstructure of the electrode. The electrode microstructure could be controlled by the dispersion medium used for the electrode slurry. The La_0.6Sr_0.4MnO₃ electrode coated with n-butyl acetate slurry exhibited the smallest electrode resistance.