Characterization and electrochemical properties of CF4 plasma-treated boron-doped diamond surfaces

The effect of CF₄ plasma etching on diamond surfaces, with respect to treatment time, was investigated using scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and electrochemical measurements. SEM observations and Raman spectra indicated an increase in surface roughening on a scale of 10–20 nm, and an increase in crystal defect density was apparent with treatment time in the range of 10 s to 30 min. In contrast, alteration of the diamond surface terminations from oxygen to fluorine was found to be rather rapid, with saturation of the F/C atomic ratio estimated from XPS analysis after treatment durations of 1 min and more. The redox kinetics of Fe(CN)₆^3−/4− was also found to be significantly modified after 10 s of CF₄ plasma treatment. This behavior shows that C–F terminations predominantly affect the redox kinetics compared to the effect on the surface roughness and crystal defects. The double-layer capacitance (C_dl) of the electrolyte/CF₄ plasma-treated boron-doped diamond interface was found to show a minimum value at 1 min of treatment. These results indicate that a short-duration CF₄ plasma treatment is effective for the fabrication of fluorine-terminated diamond surfaces without undesirable surface damage.     

High-efficiency finishing process for metal mold by large-area electron beam irradiation

A new finishing process for metal molds by large-area electron beam (EB) irradiation is proposed in this study. In the large-area EB irradiation equipment used here, an EB with high-energy density is irradiated without focusing the beam, and so the EB with a maximum diameter of 60 mm can be used for melting or evaporating metal surface instantly. Experimental results show that the surface roughness decreases from 6 μmRz to less than 1 μmRz in just a few minutes under proper machining conditions. The corrosion resistance of metal mold surface also could be greatly improved by large-area EB irradiation. Furthermore, the surface roughness of tilting surface close to 90° could be well improved. Therefore, large-area EB irradiation method has a possibility to become a high-efficiency finishing process for metal molds.     

The result of a wall failure in-pile experiment under the EAGLE project

The WF (wall failure) test of the EAGLE program, in which 2 kg of uranium dioxide fuel-pins were melted by nuclear heating, was successfully conducted in the IGR (Impulse Graphite Reactor) of NNC/Kazakhstan. In this test, a 3 mm-thick stainless steel (SS) wall structure was placed between fuel pins and a 10 mm-thick sodium-filled channel (sodium gap). During the transient, fuel pins were heated, which led to the formation of a fuel-steel mixture pool. Under the transient nuclear heating condition, the SS wall was strongly heated by the molten pool, leading to wall failure. The time needed for fuel penetration into the sodium-filled gap was very short (less than 1 s after the pool formation). The result suggests that molten core materials formed in hypothetical LMFBR core disruptive accidents have a certain potential to destroy SS-wall boundaries early in the accident phase, thereby providing fuel escape paths from the core region. The early establishment of such fuel escape paths is regarded as a favorable characteristic in eliminating the possibility of severe re-criticality events. A preliminary interpretation on the WF test results is presented in this paper.     

A variational approach to multi-phase motion of gas, liquid and solid based on the level set method

We propose a simple and robust numerical algorithm to deal with multi-phase motion of gas, liquid and solid based on the level set method [S. Osher, J.A. Sethian, Front propagating with curvature-dependent speed: Algorithms based on Hamilton-Jacobi formulation, J. Comput. Phys. 79 (1988) 12; M. Sussman, P. Smereka, S. Osher, A level set approach for capturing solution to incompressible two-phase flow, J. Comput. Phys. 114 (1994) 146; J.A. Sethian, Level Set Methods and Fast Marching Methods, Cambridge University Press, 1999; S. Osher, R. Fedkiw, Level Set Methods and Dynamics Implicit Surface, Applied Mathematical Sciences, vol. 153, Springer, 2003]. In Eulerian framework, to simulate interaction between a moving solid object and an interfacial flow, we need to define at least two functions (level set functions) to distinguish three materials. In such simulations, in general two functions overlap and/or disagree due to numerical errors such as numerical diffusion. In this paper, we resolved the problem using the idea of the active contour model [M. Kass, A. Witkin, D. Terzopoulos, Snakes: active contour models, International Journal of Computer Vision 1 (1988) 321; V. Caselles, R. Kimmel, G. Sapiro, Geodesic active contours, International Journal of Computer Vision 22 (1997) 61; G. Sapiro, Geometric Partial Differential Equations and Image Analysis, Cambridge University Press, 2001; R. Kimmel, Numerical Geometry of Images: Theory, Algorithms, and Applications, Springer-Verlag, 2003] introduced in the field of image processing.     

Buoyancy engine developed for underwater gliders

A buoyancy engine with a swashplate-type axial piston pump was developed. Its oil extrusion and drawing properties under high hydraulic pressure were evaluated. This buoyancy engine is now installed in an underwater glider that will achieve long-term monitoring of ocean environments up to 2100 m depth in a designated area with lower operational costs. This bidirectionally functioning pump can control the amount of oil in extrusion and draw operations. When drawing oil under high pressure, the hydraulic pump and the electric motor, respectively, act as a hydraulic motor and an electric generator. The generated electric power is absorbed by a damping resistor. The oil-drawing and extrusion properties were measured using a large hyperbaric chamber that is able to produce an almost identical environment to that of actual operations. Results confirmed stable oil extrusion operations up to 21 MPa. Regarding oil-drawing properties, although it was measured only up to 10 MPa in the hyperbaric chamber, it can be inferred that the system can draw the oil and can control the buoyancy precisely up to 21 MPa by replacing the two-way ball valve with an electromagnetic latching solenoid valve.     

Compact electrostatic levitator for diffraction measurements with a two axis diffractometer and a laboratory x-ray source

A compact electrostatic levitator was developed for the structural analysis of high-temperature liquids by x-ray diffraction methods. The size of the levitator was 200 mm in diameter and 200 mm in height and can be set up on a two axis diffractometer with a laboratory x-ray source, which is very convenient in performing structural measurements of high-temperature liquids. In particular, since the laboratory x-ray source allows a great amount of user time, preliminary or challenging experiments can be performed with trial and error, which prepares and complements synchrotron x-ray experiments. The present small apparatus also provides the advantage of portability and facility of setting. To demonstrate the capability of this electrostatic levitator, the static structure factors of alumina and silicon samples in their liquid phases were successfully measured.     

Preparation of β-Fesi2 thin film by metal organic chemical vapor deposition using iron-carbonyl and mono-silane

β-FeSi₂ films were deposited at 750 °C by a supplying Fe(CO)₅ and SiH₄ simultaneously during metal organic chemical vapor deposition (CVD). Films could be deposited using this precursors system, even though film deposition was not ascertained by the single supply of Fe(CO)₅. Fe(CO)₅ was probably decomposed in gas phases before it reached to substrate surface. It was suggested that a kind of intermediate reactant which was more stable than Fe(CO)₅ created by the simultaneous supply of Fe(CO)₅ and SiH₄ makes Fe-Si films. Epitaxial β-FeSi₂ films were obtained on Si(111) substrates, and neither carbide nor oxide phases were detected on XRD patterns.     

Characterization by Stm and Electrical Conductivity of Single-Walled Carbon Nanotubes

Abstract

Single-walled carbon nanotubes (SWCNT) prepared by a DC-Arc-Discharge and purified by a hydrothermal treatment followed by several steps of procedures including heating, burning, extracting and acid-washing are investigated by a conventional STM technique morphologically and spectroscopically. The electical resistivities of compacted pellets (mats) of SWCNT are measured as a function of temperature in the range from the room-temperature to 1.5K. The behaviors seems to be essentially originated in the metallic nature of individual SWCNT.     

Well‐Defined Functional Linear Aliphatic Diblock Copolyethers: A Versatile Linear Aliphatic Polyether Platform for Selective Functionalizations and Various Nanostructures

Low‐temperature anionic ring‐opening homopolymerizations and copolymerizations of two glycidol derivatives (allyl glycidyl ether (AGE) and ethoxyethyl glycidyl ether (EEGE)) are studied using a metal‐free catalyst system, 3‐phenyl‐1‐propanol (PPA) (an initiator) and 1‐tert‐butyl‐4,4,4‐tris(dimethylamino)‐2,2‐bis[tris‐(dimethylamino)phosphoranylidenamino]‐2Λ⁵,4Λ⁵‐catenadi(phosphazene) (t‐Bu‐P₄) (a promoter) in order to obtain well‐defined functional linear polyethers and diblock copolymers. With the aid of the catalyst system, AGE is found to successfully undergo anionic ring‐opening polymerization (ROP) even at room temperature (low reaction temperature) without any side reactions, producing well‐defined linear AGE‐homopolymer in a unimodal narrow molecular weight distribution. Under the same conditions, EEGE also undergoes polymerization, producing a linear EEGE‐homopolymer in a unimodal narrow molecular‐weight distribution. In this case, however, a side reaction (i.e., chain‐transfer reaction) is found to occur at low levels during the early stages of polymerization. The chemical properties of the monomers in the context of the homopolymerization reactions are considered in the design of a protocol used to synthesize well‐defined linear diblock copolyethers with a variety of compositions. The approach, anionic polymerization via the sequential step feed of AGE and EEGE as the first and second monomers, is found to be free from side reactions at room temperature. Each block of the obtained linear diblock copolymers undergoes selective deprotection to permit further chemical modification for selective functionalization. In addition, thermal properties and structures of the polymers and their post‐modification products are examined. Overall, this study demonstrates that a low‐temperature metal‐free anionic ROP using the PPA/t‐Bu‐P₄ catalyst system is suitable for the production of well‐defined linear AGE‐homopolymers and their diblock copolymers with the EEGE monomer, which are versatile and selectively functionalizable linear aliphatic polyether platforms for a variety of post‐modifications, nanostructures, and their applications.     

Polypropylene plasticization and photodegradation with a TiO2/poly(ethylene oxide)/methyl linoleate paint photocatalyst system

The photodegradation of polypropylene (PP) film was performed by a TiO₂/polyethylene oxide (PEO)/plant oil paint photocatalyst system. The photodegradation underwent two stages of development as follows: Initially PP reacted with linoleic acid radical originated from the photoreaction of plant oil component. Second, the linoleic acid graft‐polymer was decomposed, and then PP chain scission was caused. The process was studied using methyl linoleate (ML) in detail. The melting point of the 24 h‐photodegraded PP slightly decreased, and those of the 48 h‐ and 96 h‐ones drastically did as compared with the pristine PP. The crystallinity (χ_c) decreased at the 48 h photodegradation time and drastically increased at the 96 h one. The 24 h‐photodegraded PP showed the 77% Young's modulus, 88% tensile strength, and 103% strain at break values to those of the pristine PP. The ML graft‐polymerization and decomposition brought about the PP plasticizing and chemi‐crystallization, causing the PP degradation. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39909.