放电等离子烧结对纳米TiN增强Ti-6Al-4V显微组织和磨损行为的影响（英文）

采用放电等离子烧结(SPS)成功制备Ti-6Al-4V/TiN复合材料。加入Ti-6Al-4V中的TiN含量变化范围为1%~5%(体积分数)。研究添加TiN对Ti-6Al-4V材料致密度、显微组织、硬度和磨损行为的影响。实验结果表明,随着TiN含量的增加,材料的烧结密度从99%降低至97%;而显微硬度值却从HV_(0.1) 389增加至HV_(0.1) 488。X射线衍射(XRD)分析表明,伴随着少量二次Ti_2N相的形成,复合材料中TiN相的衍射峰强度增加。SEM分析表明,SPS烧结Ti-6Al-4V纳米复合材料具有细化的α/β相组织及均匀分散的TiN颗粒。与无添加烧结Ti-6Al-4V相比,Ti-6Al-4V/TiN复合材料的磨损表面呈现非连续的凹槽,抗磨粒磨损性能得到提高。     

In Situ Micro-mechanical Testing of a PM Nickel-Base Superalloy Weld

Microstructural variations between the bond line and the base alloy of welds have been reported in various nickel-base superalloys that have found their applications as structural materials in aero- and land-based engines. This microstructural variation occurs within 50 to 100 μm of majority of welds. Thus, in order to characterize the strength variations between the weld and the base alloy, mechanical testing at micron level is required. This paper presents the use of a newly developed microtensile testing system for an in situ micro-mechanical testing of a powder metallurgy nickel-base superalloy, RR1000 performed in a focused ion beam scanning electron microscope.     

Liquid phase sintering of functionally graded WC–Co composites

Functionally graded cemented tungsten carbide (WC–Co) is an example of functionally graded materials (FGM) in which mechanical properties are optimized by the presence of microstructural gradients such as cobalt gradient and grain size differences within the microstructure. In particular, a cobalt gradient is preferred. However, the manufacture of FGM WC–Co with a cobalt gradient is difficult because the flow of the liquid phase during liquid phase sintering (LPS) would eliminate any initial cobalt gradient built into the powder compacts. In this paper, different factors, which can be used to influence the migration of liquid during sintering, are investigated. These factors include gradients in grain size, carbon and cobalt content, and sintering time. It is shown that a difference in particle size may induce a step-wise profile of cobalt concentration. Initial carbon content differences, however, can be used to obtain a gradient of cobalt during sintering. The effects of these factors are explained based on the roles of capillary force and phase reactions.     

Microstructural Characterization of Thermomechanical and Heat-Affected Zones of an Inertia Friction Welded Astroloy

The behaviour of γ’ phase to thermal and mechanical effects during rapid heating of Astroloy, a powder metallurgy nickel-based superalloy has been investigated. The thermo-mechanical-affected zone (TMAZ) and heat-affected zone (HAZ) microstructures of an inertia friction welded (IFW) Astroloy were simulated using a Gleeble thermo-mechanical simulation system. Detailed microstructural examination of the simulated TMAZ and HAZ and those present in actual IFW specimens showed that γ’ particles persisted during rapid heating up to a temperature where the formation of liquid is thermodynamically favored and subsequently re-solidified eutectically. The result obtained showed that forging during the thermo-mechanical simulation significantly enhanced resistance to weld liquation cracking of the alloy. This is attributable to strain-induced rapid isothermal dissolution of the constitutional liquation products within 150 μm from the center of the forged sample. This was not observed in purely thermally simulated samples. The microstructure within the TMAZ of the as-welded alloy is similar to the microstructure in the forged Gleeble specimens.     

Influence of spark plasma sintering on microstructure and wear behaviour of Ti-6Al-4V reinforced with nanosized TiN

Ti-6Al-4V/TiN composites were successfully consolidated by spark plasma sintering (SPS). TiN addition to Ti-6Al-4V was varied from 1% to 5% (volume fraction). The effect of TiN addition on the densification, microstructure, microhardness and wear behaviour of Ti-6Al-4V was studied. Experimental results showed reduction in sintered density of the compacts from 99% to 97% with increase in TiN content. However, an increase in microhardness value was recorded from HV_0.1 389 to HV_0.1 488. X-ray diffraction (XRD) analysis showed that the intensity of diffraction peaks of TiN phase in the composites increased also with formation of small amount of secondary Ti₂N phase. SEM analysis of SPS sintered nanocomposites possessed a refinement of α/β phase microstructure in Ti-6Al-4V with the presence of uniformly dispersed TiN particles. The worn surface of the composite showed improved abrasive wear resistance with non-continuous grooves as compared to the sintered Ti-6Al-4V without TiN addition.     

Refined Microstructural Formation and Corrosion Behavior of Aluminium Nanocrystalline on Nickel-Phosphate Coatings Produced from Electrolytic Time Dependent Factor

Protection of Metals and Physical Chemistry of Surfaces - Marine industries and environments is faced with corrosion and wear of materials challenge which have shortened the life span of metals and...