Benchmark experiment of large-angle scattering reaction cross section of iron at 14 MeV using two shadow bars – Comparison of experimental results with ENDF/B-VIII –

ABSTRACT

It is important to perform neutron transport simulations with accurate nuclear data in the neutronics design of a fusion reactor. However, absolute values of large-angle scattering cross sections vary among nuclear data libraries even for well-examined nuclide of iron. Benchmark experiments focusing on large-angle scattering cross sections were thus performed to confirm the correctness of nuclear data libraries. The series benchmark experiments were performed at a DT neutron source facility, OKTAVIAN of Osaka University, Japan, by the unique experimental system established by the authors’ group, which can extract only the contribution of large-angle scattering reactions. This system consists of two shadow bars, target plate (iron), and neutron detector (niobium). Two types of shadow bars were used and four irradiations were conducted for one experiment, so that contribution of room-return neutrons was effectively removed and only large-angle scattering neutrons were extracted from the measured four Nb reaction rates. The obtained experimental results were compared with calculations for five nuclear data libraries including JENDL-4.0, JEFF.-3.3, FENDL-3.1, ENDF/B- VII, and recently released ENDF/B-VIII. It was found from the comparison that ENDF/B-VIII showed the best result, though ENDF/B-VII showed overestimation and others are in large underestimation at 14 MeV.     

Thermal desorption and pyrolysis direct analysis in real time mass spectrometry of Nafion membrane

Perfluorosulfonic acid ionomer membranes have been widely used as proton conducting membranes in various electrochemical processes such as polymer electrolyte fuel cells and water electrolysis. While their thermal stability has been studied by thermogravimetry and analysis of low molecular weight products, their decomposition mechanism is little understood. In this study a newly developed methodology of thermal desorption and pyrolysis in combination with direct analysis in real time mass spectrometry is applied for Nafion membrane. An ambient ionization source and a high-resolution time-of-flight mass spectrometer enabled unambiguous assignment of gaseous products. Thermal decomposition is initiated by side chain detachment above 350°C, which leaves carbonyls on the main chain at the locations of the side chains. Perfluoroalkanes are released above 400°C by main chain scission and their further decomposition products dominate above 500 °C. DFT calculation of reaction energies and barrier heights of model compounds support proposed decomposition reactions.     

Distribution of carbon contamination in MgAl2O4 spinel occurring during spark-plasma-sintering (SPS) processing: I – Effect of heating rate and post-annealing

Carbon contamination from the carbon paper/dies during spark-plasma-sintering (SPS) processing was examined in the MgAl₂O₄ spinel. The carbon contamination sensitively changes with the heating rate during the SPS processing. At the high heating rate of 100 °C/min, the carbon contamination having organized structures occurred over almost the entire area from the surface to deep inside the SPSed spinel disk. In contrast, at the slow heating rate of 10 °C/min, the carbon contamination having disordered structures occurred only around the surface area. The carbon phases transform into high pressure CO/CO₂ gases by post-annealing in air and lead to pore formation along the grain junctions. The pore formation significantly occurs at the high heating rate due to the large amount of the contaminant carbon phases. This suggests that if once the carbon contamination was formed in the materials, it is very difficult to remove the carbon phases from the materials.     

An efficient manufacturing method for I-shaped cross-sectional CFRP beam with arbitrary arrangement of carbon fiber using electro-activated resin molding

Abstract

The I-shaped cross-sectional beam of CFRP (CFRP I-beam) is usually manufactured by the continuous protrusion method. Carbon fibers can only be arranged in the longitudinal direction. The CFRP I-beam with arbitrary arrangement of carbon fiber was manufactured with applying the electro-activated deposition molding method. The carbon fiber fabric was immersed in the deposition solution and energized, epoxy resin precipitated around carbon fiber and impregnated. The resin-impregnated fabric was installed to the mold, and the CFRP I-beam was fabricated. The CFRP I-beam was subjected to three-point bending tests, and the relationship between load-deflection was simulated by finite-element analysis.     

Fracture and deformation properties of Ni-Fe superalloy in cryogenic high magnetic field environments

The present paper includes experimental and analytical data on the fracture properties of a nickel-iron superalloy, a ferromagnetic austenite, at 4 K in magnetic fields of 0 and 6 T. The tensile, notch tensile and small punch tests are employed. A finite element analysis is also performed to convert the experimentally measured load-displacement data into useful engineering information. To interpret the results we review the available theory of the influence of magnetic field on the stress intensity factor for a crack in ferromagnetic materials.     

A CMOS multichannel 10-Gb/s transceiver

We describe a CMOS multichannel transceiver that transmits and receives 10 Gb/s per channel over balanced copper media. The transceiver consists of two identical 10-Gb/s modules. Each module operates off a single 1.2-V supply and has a single 5-GHz phase-locked loop to supply a reference clock to two transmitter (Tx) channels and two receiver (Rx) channels. To track the input-signal phase, the Rx channel has a clock recovery unit (CRU), which uses a phase-interpolator-based timing generator and digital loop filter. The CRU can adjust the recovered clock phase with a resolution of 1.56 ps. Two sets of two-channel transceiver units were fabricated in 0.11-/spl mu/m CMOS on a single test chip. The transceiver unit size was 1.6 mm /spl times/ 2.6 mm. The Rx sensitivity was 120-mVp-p differential with a 70-ps phase margin for a common-mode voltage ranging from 0.6 to 1.0 V. The evaluated jitter tolerance curve met the OC-192 specification.     

A new lateral MOS-gated thyristor with controlling base-current

A new lateral MOS-gated thyristor, called the Base-Current-Controlled Thyristor, is described. This device is designed so that most holes at the on-stage reach the P base through the floating P⁺ region adjacent to the P base and the on-state MOSFET. At the turn-off stage, the interruption of the hole current to the P base due to switching off the above MOSFET occurs simultaneously with the conventional turn-off operation. The concept of this device is verified experimentally by using the fabricated lateral device with the external MOSFET. This device exhibits a better trade-off relation between the on-state voltage and the turn-off time compared uith the conventional MOS-gated thyristor     

Neural mechanism of pupillary dilation elicited by electro-acupuncture stimulation in anesthetized rats

The neural mechanisms to reflex dilation elicited by electro-acupuncture stimulation were investigated in anesthetized rats. Two needles, with 160 microns diameter and about 5 mm apart, were inserted into the skin and underlying muscle of a hindpaw. Repetitive 20 Hz, 0.5 ms electrical pulses at various intensities were used for stimulation for 30s. The pupil size was magnified about 44 times via a microscope and was continuously recorded on a videotape. Electro-acupuncture stimulation at more than 0.5 up to 6 mA induced stimulus intensity-dependent pupil dilation. These responses were abolished by the severance of the sciatic and saphenous nerve of the stimulated hindlimb. Compound action potentials were recorded from the distal cut end of the tibial of a saphenous nerve following electro-acupuncture stimulation of the hindpaw. The mean threshold of the compound action potentials of the myelinated fibers in saphenous nerves was 0.18 mA, while that of unmyelinated fibers was 3.0 mA. The mean threshold of the compound action potentials of the myelinated fibers in the tibial nerve was 0.20 mA of unmyelinated fibers was 3.3 mA. Severance of bilateral trunks did not affect the response, while severance of the third cranial nerves abolished the responses. In conclusion, electro-acupuncture stimulation applied to the hindpaws of the anesthetized rats induced excitation of myelinated or of both myelinated and unmyelinated afferent fibers of the tibial and saphenous nerve, and involved a reflex response of pupil dilation through the third cranial parasympathetic efferent nerve.     

Highly reliable 200 mW AlGaAs laser diode with fundamental transverse mode

A highly reliable 200 mW AlGaAs laser diode with a fundamental transverse mode has been developed, by optimising its structure with a 0.8 mu m thick p-cladding layer, a 1200 mu m long cavity length, and a front facet coating with a low reflectivity of 2%. The maximum output power was 500 mW, and stable fundamental transverse mode operation was obtained up to 350 mW. Stable operation under 200 mW and 50 degrees C was confirmed for more than 1200 h. Optical feedback noise was below 3*10/sup -14/ Hz/sup -1/.<>