Pulsed KrF excimer laser annealing of silicon solar cell

The pulsed KrF excimer laser annealing of silicon films for solar cell with EBEP-CVD and LP-CVD was studied theoretically and experimentally. Three-dimensional thermal diffusion equation for microcrystalline and amorphous silicon was solved by using the finite difference methods. The results of our heat-flow simulation of laser re-crystallization in a laser irradiation with 50 ns pulse duration almost agree with the experimental results in re-crystallization depth of 0.7 μm for microcrystalline silicon (EBEP-CVD) and 0.4 μm for amorphous silicon (LP-CVD) in a single pulse excimer laser annealing.     

Densification and Thermal Conductivity of AIN Doped with Y2O3, CaO, and Li2O

Small amounts of Li₂O result in sintering in the AIN-Y₂O₃-CaO and AIN-CaO systems at firing temperatures <1600°C. The effect is ascribed to reduction of the liquidus temperature. Furthermore, Li₂O is removed by volatization at temperatures from 1300° to 1600°C, and its content decreases several ppm from the initial 0.3 wt%. Li₂O-doped AIN specimens containing Y₂O₃ and CaO additives are well densified by firing at 1600°C for 6 h, and their thermal conductivity is 135 W^.m^−1.K⁻¹.The effect of Li₂O addition on sintering and thermal conductivity also is discussed through thermo-dynamic considerations.     

High Thermal Conductivity in Silicon Nitride with Anisotropie Microstructure

Silicon nitride was fabricated by tape casting of α-Si₃N₄ powder with 5 wt% Y₂O₃ and 5 vol% rodlike β-Si₃N₄ seed particles, followed by tape stacking, hot pressing under 40 MPa, and annealing at 1850°C for 2-66 h under a nitrogen pressure of 0.9 MPa. Silicon nitrides fabricated by this procedure exhibited a highly anisotropic microstructure with large elongated grains (developed from seed particles) uniaxially oriented parallel to the casting direction. Thermal conductivities parallel to the grain alignment were much higher than those measured in other directions and exhibited high values of up to 120 W/(m.K). The anisotropic thermal conductivity of the specimen could be explained by the rule of mixture, considering that large elongated grains developed from seeds have higher thermal conductivity than a small-grained matrix.     

Immobilization of glucose oxidase on nonwoven fabrics with bombyx mori silk fibroin gel

The enzyme glucose oxidase (GOD) was immobilized on the nonwoven fabrics, which have excellent properties in diffusivity of substrates, mechanical strength, and handling, with Bombyx mori silk fibroin gel. The nonwoven fabrics of silk fibroin, viscose rayon, poly-ethyleneterephthalate, 6-nylon, and polypropylene with activated surface by fluoline treatment were used. The stabilities of GOD to heat or pH changes were much improved by the immobilization as well as the case of the GOD immobilized in the silk fibroin membrane. Among nonwoven fabrics, silk fibroin was the most excellent support material for the immobilization of GOD although all nonwoven fabrics used here are able to be used as the support materials. The increase of the sensitivity was observed when the glucose sensor was made with the GOD immobilized on nonwoven silk fabrics as four times compared with the case of the GOD immobilized in the silk fibroin membrane.     

Transient analysis of the release and reduction of NOx using a Pt/Ba/Al2O3 catalyst

The release and reduction of NO_x in a NO_x storage-reduction (NSR) catalyst were studied with a transient reaction analysis in the millisecond range, which was made possible by the combination of pulsed injection of gases and time resolved time-of-flight mass spectrometry. After an O₂ pulse and a subsequent NO pulse were injected into a pellet of the Pt/Ba/Al₂O₃ catalyst, the time profiles of several gas products, NO, N₂, NH₃ and H₂O, were obtained as a result of the release and reduction of NO_x caused by H₂ injection. Comparing the time profiles in another analysis, which were obtained using a model catalyst consisting of a flat 5 nmPt/Ba(NO₃)₂/cordierite plate, the release and reduction of NO_x on Pt/Ba/Al₂O₃ catalyst that stored NO_x took the following two steps; in the first step NO molecules were released from Ba and in the second step the released NO was reduced into N₂ by H₂ pulse injection. When this H₂ pulse was injected in a large amount, NO was reduced to NH₃ instead of N₂.

A only small amount of H₂O was detected because of the strong affinity for alumina support. We can analyze the NO_x regeneration process to separate two steps of the NO_x release and reduction by a detailed analysis of the time profiles using a two-step reaction model. From the result of the analysis, it is found that the rate constant for NO_x release increased as temperature increase.     

Pulsed Electric Current Sintering of Silicon Nitride

Pulsed electric current sintering (PECS) has been used to densify α-Si₃N₄ powder doped with oxide additives of Y₂O₃ and Al₂O₃. A full density (>99%) was achieved with virtually no transformation to β-phase, resulting in a microstructure with fine equiaxed grains. With further holding at the sintering temperature, the α-to-β phase transformation took place, concurrent with an exaggerated grain growth of a limited number of elongated β-grains in a fine-grained matrix, leading to a distinct bimodal grain size distribution. The average grain size was found to obey a cubic growth law, indicating that the growth is diffusion-controlled. In contrast, the densification by hot pressing was accompanied by a significant degree of the phase transformation, and the subsequent grain growth gave a broad normal size distribution. The apparent activation energy for the phase transformation was as high as 1000 kJ/mol for PECS, almost twice the value for hot pressing (∼500 kJ/mol), thereby causing the retention of α-phase during the densification by PECS.     

Carrier Transport and Optical Properties of InGaN SQW With Embedded AlGaN$delta$-Layer

We investigate the carrier transport and optical properties of a thick InGaN single quantum well (SQW) where an AlGaN delta-layer is embedded. By way of simulation, it is found that the carrier density distribution in the active region is more uniform in such a QW structure, compared to a double QW (DQW) configuration showing a discontinuity in the hole quasi-Fermi level due to the large effective mass of the holes along with the strong piezoelectric field. Through the photoluminescence (PL) measurements, we have shown that the PL peak energy varies depending sensitively on the delta-layer thickness, providing an extra degree of freedom in the wavelength-tuning control. In particular, such a QW structure is highly desired for long-wavelength emission as the wavelength tuning can be achieved with lower indium composition. The embedded delta-layer also increases the wave function overlap between holes and electrons, thereby shortening the PL lifetime. The results of PL measurements are shown to be consistent with the self-consistent numerical results. A possible application of the proposed QW structure is to the design of long-wavelength light-emitting diodes and laser diodes     

Partial redundancy elimination for access expressions by speculative code motion

We present a new memory access optimization for Java to perform aggressive code motion for speculatively optimizing memory accesses by applying partial redundancy elimination (PRE) techniques. First, to reduce as many barriers as possible and to enhance code motion, we perform alias analysis to identify all the regions in which each object reference is not aliased. Secondly, we find all the possible barriers. Finally, we perform code motions in three steps. For the first step, we apply a non‐speculative PRE algorithm to move load instructions and their following instructions in the backwards direction of the control flow graph. For the second step, we apply a speculative PRE algorithm to move some of them aggressively before the conditional branches. For the third step, we apply our modified version of a non‐speculative PRE algorithm to move store instructions in the forward direction of the control flow graph and to even move some of them after the merge points. We implemented our new algorithm in our production‐level Java just‐in‐time compiler. Our experimental results show that our speculative algorithm improves the average (maximum) performance by 13.1% (90.7%) for jBYTEmark and 1.4% (4.4%) for SPECjvm98 over the fastest algorithm previously described, while it increases the average (maximum) compilation time by 0.9% (2.9%) for both benchmark suites. Copyright © 2004 John Wiley & Sons, Ltd.     

Effects of water chemistry and potential distribution on electrochemical corrosion potential measurements in 553 K pure water

The effects of water chemistry distribution on the potential of a reference electrode and of the potential distribution on the measured potential should be known qualitatively to obtain accurate electrochemical corrosion potential (ECP) data in BWRs. First, the effects of oxygen on a platinum reference electrode were studied in 553 K pure water containing dissolved hydrogen (DH) concentration of 26–105 μg kg^?1 (ppb). The platinum electrode worked in the same way as the theoretical hydrogen electrode under the condition that the molar ratio of DH to dissolved oxygen (DO) was more than 10 and that DO was less than 100 ppb. Second, the effects of potential distribution on the measured potential were studied by using the ECP measurement part without platinum deposition on the surfaces connected to another ECP measurement part with platinum deposition on the surfaces in 553 K pure water containing 100–130 ppb of DH or 100–130 ppb of DH plus 400 ppb of hydrogen peroxide. Measured potentials for each ECP measurement part were in good agreement with literature data for each surface condition. The lead wire connecting point did not affect the measured potential. Potential should be measured at the nearest point from the reference electrode in which case it will be not affected by either the potential distribution or the connection point of the lead wire in pure water.     

Microfluidic Spinning of Cell‐Responsive Grooved Microfibers

Engineering living tissues that simulate their natural counterparts is a dynamic area of research. Among the various models of biological tissues being developed, fiber‐shaped cellular architectures, which can be used as artificial blood vessels or muscle fibers, have drawn particular attention. However, the fabrication of continuous microfiber substrates for culturing cells is still limited to a restricted number of polymers (e.g., alginate) having easy processability but poor cell–material interaction properties. Moreover, the typical smooth surface of a synthetic fiber does not replicate the micro‐ and nanofeatures observed in vivo, which guide and regulate cell behavior. In this study, a method to fabricate photocrosslinkable cell‐responsive methacrylamide‐modified gelatin (GelMA) fibers with exquisite microstructured surfaces by using a microfluidic device is developed. These hydrogel fibers with microgrooved surfaces efficiently promote cell encapsulation and adhesion. GelMA fibers significantly promote the viability of cells encapsulated in/or grown on the fibers compared with similar grooved alginate fibers used as controls. Importantly, the grooves engraved on the GelMA fibers induce cell alignment. Furthermore, the GelMA fibers exhibit excellent processability and could be wound into various shapes. These microstructured GelMA fibers have great potential as templates for the creation of fiber‐shaped tissues or tissue microstructures.