Investigation on external stimuli engendered magnetic ordering in polycrystalline CaCu3Ti4O12 quadruple perovskite

The consequences of high energy mechanical milling, microwave-assisted heating and rapid thermal cooling on magnetic ordering in polycrystalline CaCu₃Ti₄O₁₂ cubic perovskite have been investigated by means of X-ray powder diffractometry (300?K), dc magnetization in field – cooled and zero – field cooled modes (H = 100?Oe and 1000?Oe, T?=?5–300?K) (M – T curves) and M – H loop characteristics (T?=?5?K and 300?K, H_max = 70?kOe). The M – T curves of unmilled and 16?h milled samples show pure antiferromagnetic and weak ferromagnetic ordering, respectively, 1?h and 6?h milled samples demonstrate the coexistence of both the phases while microwave-assisted and quenched samples exhibit classic antiferromagnetic transition and a low temperature paramagnetic–like contribution with different weights, well supported by the M – H loop characteristics. The observed transformations in the magnetic ordering are attributed to the ball-milling induced stress which curtails hybridization of empty Ti-3d orbitals with Cu-3d and O-2p orbitals and secondary phase formation. Oxygen vacancies associated with bound magnetic polarons originate ferromagnetism in the milled samples while unpaired electrons inhabited at the empty sites are the cause of paramagnetic centers. The low-temperature Curie – tail in M – T curve for quenched and microwave assisted samples is attributed to Ti³⁺ cations.     

Influence of Different Additives on the Interaction of Quinolone Antibiotic Drug with Surfactant: Conductivity and Cloud Point Measurement Study

Conductometric and cloud point (CP) measurement studies have been performed to investigate the interaction of tetradecyltrimethylammonium bromide (TTAB) and Triton® X-100 (TX-100) with ciprofloxacin hydrochloride (CFH) in different solvents over the temperature range of 295.15–315.15 K. CFH is used for the treatment of various bacterial infections. The observed critical micelle concentration (CMC) values of TTAB were found to be reduced in the presence of electrolytes (Na₂SO₄/Na₃PO₄), and this reduction proceeds with the elevation of salt concentration. The order of the CMC of TTAB follows the trend: > >. The observed CMC values of TTAB were found to increase with increasing temperature and decrease with increasing concentration of CFH in aqueous medium. The values of Gibbs free energy of micellization () for the TTAB/TTAB + CFH mixture were found to be negative, implying spontaneous micellization. The estimated CP of TX-100 decreases with increasing concentration of TX-100 in aqueous medium. The CP values first decrease with increasing concentration of CFH and then increase at higher concentration of CFH almost in all cases investigated. The values of free energy of clouding were found to be positive in all cases studied implying that phase separation of TX-100 was nonspontaneous. The other thermodynamic parameters associated with the micellization of TTAB and the phase separation of TX-100 were estimated and explained.     

1-methyl-4-phenyl-1,2,3,6-tetrahydropyridine as a substrate of cytochrome P450 2D6: allosteric effects of NADPH-cytochrome P450 reductase

1-Methyl-4-phenyl-1,2,3,6-tetrahydropyridine (MPTP), a neurotoxin that produces Parkinsonism symptoms in man, has been examined as a substrate of recombinant human cytochrome P450 2D6. When cumene hydroperoxide is used as an oxygen and electron donor, a single product is formed, identified as 4-phenyl-1,2,3,6-tetrahydropyridine. The K(m) for formation of this product (130 microM) is in agreement with the dissociation constants for MPTP binding to the enzyme determined by optical and nuclear magnetic resonance (NMR) spectroscopy. When the reaction is carried out with nicotinamide adenine dinucleotide phosphate (reduced) (NADPH) and recombinant human NADPH-cytochrome P450 reductase, a second product, identified as 1-methyl-4-(4'-hydroxyphenyl)-1,2,3,6-tetrahydropyridine, is formed in addition to 4-phenyl-1,2,3,6-tetrahydropyridine. The K(m) values for formation of these two products are 19 microM and 120 microM, respectively. Paramagnetic relaxation experiments have been used to measure distances between the protons of bound MPTP and the heme iron, and these have been used to construct models for the position and orientation of MPTP in the active site. For the cytochrome alone, a single mode of binding was observed, with the N-methyl close to the heme iron in a position appropriate for the observed N-demethylation reaction. In the presence of the reductase, the data were not consistent with a single mode of binding but could be explained by the existence of two alternative orientations of MPTP in the active site. One of these, characterized by a dissociation constant of 150 microM, is essentially identical to that observed in the absence of the reductase. In the second, which has a K(d) of 25 microM, the MPTP is oriented so that the aromatic ring is close to the heme iron, in a position appropriate for p-hydroxylation leading to the formation of the product seen only in the presence of the reductase. In the case of codeine, another substrate for cytochrome P450 2D6, the addition of reductase had no effect on the nature of the product formed, the dissociation constant, or the orientation in the binding site. These observations show that NADPH-cytochrome P450 reductase has an allosteric effect on the active site of cytochrome P450 2D6 that affects the binding of some substrates but not others.     

On the boundary-layer control through momentum injection: Studies with applications

The concept of moving surface boundary-layer control, as applied to a Joukowsky airfoil, is investigated through a planned experimental programme complemented by numerical studies. The moving surface was provided by rotating cylinders located at the leading edge and/or trailing edge as well as top surface of the airfoil. Results suggest that the concept is quite promising, leading to a substantial increase in lift and a delay in stall. Depending on the performance desired, appropriate combinations of cylinder geometry, location and speed can be selected to obtain favourable results over a wide range of angle of attack. Next, effectiveness of the concept in reducing drag of bluff bodies such as a two-dimensional flat plate at large angles of attack, rectangular prisms and three-dimensional models of trucks is assessed through an extensive wind tunnel test-programme. Results show that injection of momentum through moving surfaces, achieved here by introduction of bearing-mounted, motordriven, hollow cylinders, can significantly delay separation of the boundary-layer and reduce the pressure drag. The momentum injection procedure also proved effective in arresting wind-induced vortex resonance and galloping type of instabilities. A flow visualization study, conducted in a closed-circuit water tunnel using slit lighting and polyvinyl choride tracer particles, adds to the wind-tunnel and numerical investigations. It shows, rather dramatically, the effectiveness of the moving surface boundary-layer control (MSBC). The Sabita Chaudhury Memorial Lecture The models were fabricated in the Mechanical Engineering Workshop. The assistance of M/s E Abell, P Hurren and D Camp in the design and construction of the models is gratefully acknowledged. The investigation was supported by the Natural Sciences and Engineering Research Council of Canada, Grant No. A-2181.     

Case report: possible Lyme endocarditis

A 56-year-old male presented with clinical and serological data suggestive of Lyme disease. The patient was found to have an aortic valvular vegetation by transesophageal echocardiography. This report represents the first case of Lyme disease with possible valvular involvement.     

Mössbauer spectroscopic studies of Fe-substituted YIG

Compositional dependence of hyperfine parameters, determined through Mössbauer spectral analysis has been studied for Y_3−xFe_5+xO₁₂ (x = 0.0, 0.1, 0.3 and 0.5) garnet system at 300 K. The Mössbauer spectra have been fitted with three sextets in the ferrimagnetic state corresponding to Fe³⁺ ions at tetrahedral (d), octahedral (a) and dodecahedral (c) sites of the crystal structure. It is observed that isormershift, quadrupole shift and hyperfine field of d-site show no significant variation with Fe³⁺ concentration. The change in hyperfine fields of a- and c-sites with composition (x) has been explained on the basis of strength of exchange integrals, change in isomershift can be understood due to s-electron charge distribution and asymmetric displacement of oxygen ions surrounding the a- and c-sites seems to be responsible for observable quadrupole shift. The magneton number values obtained from magnetization and Mossbauer data are in agreement to those calculated using Neel's three sublattice model of ferrimagnetism.     

A design advisor for the optimal inspection of circularity tolerance

In the wake of growing importance for quality and the need to reduce inspection costs simultaneously, the need for a scientific method of selecting an optimum inspection strategy for coordinate measuring machine (CMM) based inspection has become very important. The inspection error resulting from CMM inspection is greatly affected by the profile irregularities and the sampling strategy, which includes sample size, sampling methods, and algorithms used for form evaluation. This paper describes a system that can recommend an optimal inspection plan based on the needs of the user. A design of experiments (DOE) based approach is used to relate the inspection error with sampling strategies. Surface irregularities are included in the form of lobes formed on the profile. A new two-way model is proposed that works in both directions between the sampling strategy and the performance metrics. The results indicate that the number of lobes and the sampling method used have little impact on the inspection error, while the sample size and form evaluation algorithms have a significant influence. An inspection plan advisor is presented, which provides an inspection plan based on the estimated shape and acceptable measurement error.