The effects produced by annealing Y2O3 nanopowders on their spark plasma sintering (SPS) behavior are systematically investigated in this work. It is found that the annealed powders display higher sinterability with respect to the as‐received ones. Indeed, the maximum densification level reached from pristine powders is about 97.5%, whereas density decreases when further increasing either the sintering temperature or the dwell time. In contrast, the density of SPS products obtained from pretreated powder monotonically increases with temperature and processing time, thus leading to fully dense materials in 30 min at 1050°C and 60 MPa. Correspondingly, it is found that the annealing treatment markedly inhibits grain coarsening during SPS. Thus, dense translucent samples with grain size below 100 nm can be attained from annealed powders. On the other hand, white‐opaque specimens with significantly coarser microstructures (up to 1‐μm‐sized grains) are obtained when pristine powders are directly processed under the same sintering conditions. Furthermore, it is observed that the annealing treatment of SPS samples in air allows for graphite contamination removal, whereas no improvement in term of light transmittance is produced. 相似文献
A SAXS method for the quantitative assessment of the morphology of polymer layered silicate nanocomposites is proposed. Fitting the SAXS patterns, the number of clay layers, the periodicity of the layers in the tactoids, the thickness of the regions interposed between the clay platelets and their distributions can be measured. A good agreement with TEM data was obtained, avoiding the inconsistencies with microscopical observations often reported in the literature. 相似文献
Concluding remarks With this brief exposition of the areas covered in this special double issue on Eurotra, we shall now conclude our introduction. We hope that the volume will achieve its goals, as outlined above, at least to some extent. Certainly, much more could be said about a wide range of topics which have been covered in the lifetime or the project so far. For instance, these article, mainly written by linguists, deliberately neglect the software implementation and environment aspects of the prototype Eurotra Translation System, as well as a number of peripheral tools and components of the system that are available to the user, such as lexical data bases, text-handling mechanisms and the like. The reader interested in aspects of this kind is referred to Raw et al. 1989 for a very brief introduction, and to the Eurotra software team at the Commission of the European Communities (DG XIII, Luxembourg) for more details. However, one goal that we do hope to come close to achieving is to give a fair overview of the Eurotra linguistic theory of translation and the mainstream and sideline formalisms expressing variant versions of it. If we have come anywhere near achieving that, our gratitude is due to the numerous Eurotra colleagues who have supported us in preparing this volume, and to the editor of this journal. 相似文献
Polyolefins functionalized with diethylmaleate were mixed with poly(vinylchloride) (PVC) in different compositions. Intermolecular interactions involving the carbonyl groups of the side chains of the functionalized polyolefins and methine hydrogens of PVC were investigated by means of infrared spectroscopy. The major flexibility of the ester groups attached to the backbone chains, with respect to polyesters, seems to increase the capability of such groups to interact with groups of more polar polymers, thus allowing prediction of easier miscibility, which however also depends on the starting polyolefin structure and function-alization degree. 相似文献
Optimal sensor fault-accommodation is considered for faults modelled by an increase in measurement noise. This noise is taken to be bounded and its probabilistic properties unknown. It is assumed that intelligent (e.g. self-validating) instrumentation is in use and estimates of the noise bounds are available. The fault-tolerant controller is designed to optimize a noise rejection and a nominal reference tracking index and leads to a mixed norm minimization problem (l1/l2). We exploit known results and a particular feedback configuration to show that it is possible to optimize simultaneously without a trade-off the two performance indices. The results are applied to systems where the presence of auxiliary measurements allows for an optimal fault-accommodation strategy. Using properties of the optimal solution, we define a factorization for the optimal controller alternative to the Youla parametrization, leading to an algorithm which is optimal, transparent and efficient. 相似文献
The simultaneous synthesis and densification of dense TiC–TiB2 composite has been investigated starting from Ti, B4C, and C as reactants, and using the spark plasma sintering (SPS) technique. The optimal conditions for complete conversion of the reactants to the composite were determined for different applied DC current levels. A kinetic investigation performed allows us to conclude that solid-state diffusion is the mechanism governing the synthesis process. It is seen that TiC is the first phase formed, while TiB2 formation occurs afterward. Two intermediate boride phases, i.e. TiB and Ti3B4, are also formed but, as the SPS holding time was augmented, they were gradually and completely converted to TiB2. Moreover, it is found that in order to reach relatively high dense products, an electric current needs to be applied for time intervals longer than those required for obtaining complete conversion. A pure dense product (relative density ∼98%) was obtained when an electric pulsed current of 1100 A and a mechanical pressure of 20 MPa were applied for about 4 min. 相似文献
Lung volume reduction has been performed in patients with advanced emphysema to relieve dyspnea and improve exercise tolerance. Median sternotomy and video-assisted thoracoscopy have been proposed as equally adequate approaches; however, prolonged postoperative air leakage is the most prevalent complication in all series. For this reason, on the basis of the experience achieved with the median sternotomy approach, buttressing of the suture line with different materials and techniques for space reduction have been proposed. We describe a technique to create a pleural tent after thoracoscopic volume reduction. The thoracoscopic creation of a pleural tent is feasible and results in a duration of postoperative air leaks and hospital stays similar to that achieved with stapler line buttressing. 相似文献
Studying the changes of shape is a common concern in many scientific fields. We address here two problems: (1) quantifying the deformation between two given shapes and (2) transporting this deformation to morph a third shape. These operations can be done with or without point correspondence, depending on the availability of a surface matching algorithm, and on the type of mathematical procedure adopted. In computer vision, the re-targeting of emotions mapped on faces is a common application. We contrast here four different methods used for transporting the deformation toward a target once it was estimated upon the matching of two shapes. These methods come from very different fields such as computational anatomy, computer vision and biology. We used the large diffeomorphic deformation metric mapping and thin plate spline, in order to estimate deformations in a deformational trajectory of a human face experiencing different emotions. Then we use naive transport (NT), linear shift (LS), direct transport (DT) and fanning scheme (FS) to transport the estimated deformations toward four alien faces constituted by 240 homologous points and identifying a triangulation structure of 416 triangles. We used both local and global criteria for evaluating the performance of the 4 methods, e.g., the maintenance of the original deformation. We found DT, LS and FS very effective in recovering the original deformation while NT fails under several aspects in transporting the shape change. As the best method may differ depending on the application, we recommend carefully testing different methods in order to choose the best one for any specific application.
Creating high-quality quad meshes from triangulated surfaces is a highly nontrivial task that necessitates consideration of various application specific metrics of quality. In our work, we follow the premise that automatic reconstruction techniques may not generate outputs meeting all the subjective quality expectations of the user. Instead, we put the user at the center of the process by providing a flexible, interactive approach to quadrangulation design. By combining scalar field topology and combinatorial connectivity techniques, we present a new framework, following a coarse to fine design philosophy, which allows for explicit control of the subjective quality criteria on the output quad mesh, at interactive rates. Our quadrangulation framework uses the new notion of Reeb atlas editing, to define with a small amount of interactions a coarse quadrangulation of the model, capturing the main features of the shape, with user prescribed extraordinary vertices and alignment. Fine grain tuning is easily achieved with the notion of connectivity texturing, which allows for additional extraordinary vertices specification and explicit feature alignment, to capture the high-frequency geometries. Experiments demonstrate the interactivity and flexibility of our approach, as well as its ability to generate quad meshes of arbitrary resolution with high-quality statistics, while meeting the user’s own subjective requirements. 相似文献