影响掺矿渣的钢纤维砼强度的主要因素

研究结果表明 :水胶比、胶凝材料用量、钢纤维掺量、矿渣代水泥量对钢纤维砼强度影响显著。当矿渣取代水泥 10 %时 ,钢纤维砼强度最高。经试验选择出一个具有良好和易性和较高强度 (118MPa)的钢纤维砼配合比 ,为掺磨细矿渣的中含量超短异形钢纤维砼的设计和施工提供了试验依据     

Non-linear current–voltage characteristics related to native defects in SrTiO3 and ZnO bicrystals

SrTiO₃ and ZnO bicrystals with various types of boundaries were fabricated in order to examine their current–voltage characteristics across single grain boundaries. Their grain boundary structures were also investigated by high-resolution transmission electron microscopy. In Nb-doped SrTiO₃, electron transport behaviors depend on the type of boundaries. Random type boundaries exhibit highly non-linear current–voltage characteristics, while low angle boundaries show a slight non-linearity. On the contrary, undoped ZnO does not exhibit non-linear current–voltage characteristics in any type of boundaries including random ones. It is suggested that the differences observed in current–voltage properties between the two systems are mainly due to the difference in the accumulation behavior of acceptor-like native defects at grain boundaries. A clear non-linearity is obtained by means of Co-doping even for the highly coherent Σ1 boundary in a ZnO bicrystal. This is considered to result from the production of acceptor-like native defects by Co-doping.     

Effect of temperature on the strength and conductivity of a deformation processed Cu-20%Fe composite

The high temperature (22–600 °C) properties were evaluated for a Cu-20%Fe composite deformation processed from a powder metallurgy compact. The ultimate tensile strengths decreased with increasing temperature but were appreciably better than those of similarly processed Cu at temperatures up to 450 °C. At 600 °C, the strength of Cu-20%Fe was only slightly better than that of Cu as a result of the pronounced coarsening of the Fe filaments. However, at temperatures of 300 and 450 °C, the strength of Cu-20%Fe is about seven and six times greater, respectively, than that of Cu, as compared to about a two fold advantage at room temperature. Therefore, Cu-20%Fe composites made by deformation processing of powder metallurgy compacts have mechanical properties much superior to those of similarly processed Cu at room temperature and at temperatures up to 450 °C. The pronounced decrease in electrical conductivity of deformation processed Cu-20%Fe as compared to Cu is attributed to the appreciable dissolution of Fe into the Cu matrix which occurred during the fabrication of the starting compacts where temperatures up to 675 °C were used. While the powder metallurgy compacts used for the starting material for deformation processing in this study did not lead to a high conductivity composite, the powder metallurgy approach should still be a viable one if processing temperatures can be reduced further to prevent the dissolution of Fe into the Cu matrix.     

Mechanical properties of sinter-forged Al2O3-ZrO2 ceramics

Two kinds of composites, Al₂O₃-25 wt% ZrO₂(2 mol% Y₂O₃) (Y-ZTA), Al₂O₃-25 wt% ZrO₂(8 mol% CeO₂) (Ce-ZTA) were produced by the sinter-forging process. The effect of presintering temperature on the mechanical properties of the composites was examined. The sinter-forging process increased the room-temperature bending strength in comparison with pressureless sintering, owing to the smaller grain size in sinter-forged bodies than in pressureless sintered ones. It was found necessary to keep the presintering temperature considerably lower than sinter-forging temperature in order to improve the room-temperature strength. The strength of sinter-forged Ce-ZTA was higher than that of sinter-forged Y-ZTA. The residual surface compressive stress induced by the phase transition during grinding in Ce-ZTA was found to be effective to further improve the strength and fracture toughness.     

Surgical navigation by autostereoscopic image overlay of integral videography

This paper describes an autostereoscopic image overlay technique that is integrated into a surgical navigation system to superimpose a real three-dimensional (3-D) image onto the patient via a half-silvered mirror. The images are created by employing a modified version of integral videography (IV), which is an animated extension of integral photography. IV records and reproduces 3-D images using a microconvex lens array and flat display; it can display geometrically accurate 3-D autostereoscopic images and reproduce motion parallax without the need for special devices. The use of semitransparent display devices makes it appear that the 3-D image is inside the patient's body. This is the first report of applying an autostereoscopic display with an image overlay system in surgical navigation. Experiments demonstrated that the fast IV rendering technique and patient-image registration method produce an average registration accuracy of 1.13 mm. Experiments using a target in phantom agar showed that the system can guide a needle toward a target with an average error of 2.6 mm. Improvement in the quality of the IV display will make this system practical and its use will increase surgical accuracy and reduce invasiveness.     

Occurrence of correlation between occurrence of genital tract candidiasis in young girls and some subjective and objective examination parameters

The authors tried to find the correlation between the occurrence of genital tract candidiasis in adolescents and some subjective and objective examination parameters. The highest correlation rates were found for pudendal pruritus, lower abdominal pains and early applied antibiotic therapy material: 188 adolescent girls.