Phase behavior,density, and crystallization of polyethylene in n‐pentane and in n‐pentane/CO2 at high pressures

The phase behavior and volumetric properties of polyethylene (PE) in solutions of n‐pentane and n‐pentane/CO₂ were studied in a temperature (T) range of 370–440 K at pressures up to 60 MPa. Measurements were conducted with a variable‐volume view‐cell system equipped with optical sensors to monitor the changes in the transmitted light intensity as the P or the T of the system was changed. Lower‐critical‐solution‐temperature‐type behavior was observed for all of the liquid–liquid (L–L) phase boundaries, which shifted to higher pressures in solutions containing CO₂. The solid–fluid (S–F) phase boundaries were investigated over a P range of 8–54 MPa and took place in a narrow T range, from 374 to 378 K in this P interval. The S–F phase boundary showed a unique feature in that the demixing temperatures showed both increasing and decreasing trends with P depending on the P range. This was observed in both the PE/n‐pentane and PE/n‐pentane/CO₂ mixtures. The density of these solutions were measured as a function of P at selected temperatures or as a function of T at selected pressures that corresponded to the paths followed in approaching the phase boundaries (S–F or L–L) starting from a homogeneous one‐phase condition. The data showed a smooth variation of the overall mixture density along these paths. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2201–2209, 2003     

Use of Warranties on Highway Projects: A Real Option Perspective

Since the introduction of warranty provisions in federal highway jobs, more and more state departments of transportation (DOTs) have considered the use of such provisions to protect their initial investment. This paper describes the pros and cons of warranty contracting in highway construction based on a survey of warranty practices in the United States. In particular, the need for state DOTs to buy a warranty for a well-built project is questioned. As an alternative, this paper introduces the warranty option, which gives the DOT the right to buy a warranty only if it becomes necessary at the end of construction. This option is exercised if the performance on site warrants it. This paper describes the mechanics of the warranty option and its advantages over the conventional warranty. A bid evaluation model is also developed for the warranty option approach.     

Off-line multiresponse optimization of electrochemical surface grinding by a multi-objective programming method

The objective of this study is to optimize electrochemical grinding (ECG) process responses simultaneously by an off-line multiresponse optimization methodology. The responses considered as objectives are side and bottom overcuts, surface finish, spindle load, total metal removal rate, and wheel wear. Materials of 304 Stainless Steel are ground by the ECG process. The process variables optimized for the above objectives include electrolyte type, wheel material, grit size, grit concentration, d.c. voltage, electrolyte flow rate, wheel speed, feed rate, and ripple effect. A simple weighting method transforms the multi-objective problem into a single-objective programming format and then, by parametric variation of the weights, the set of non-dominated optimum solutions are obtained. It is shown in this paper that the multi-objective optimization methodology can be applied for an ECG operation, and that the optimal operating conditions for any given set of weights can be obtained depending upon the objectives.     

Scaling Analysis for the Axial Displacement and Pressure of Flextensional Transducers

We have examined the axial displacement, Δ h , and maximum axial pressure, P _max, of flextensional transducers such as the moonies and the rainbows with both scaling and mechanical analyses. For a constant electric field E across the transducer, Δ h / t ∝ E / t ² where t is the thickness of the rainbow or the thickness of the metal end cap of the moonie and Δ h / t , the relative axial displacement. Thus, for a constant voltage V across the transducer, Δ h / t ∝ V / t ³. As for the maximum pressure, P _max t ² for the rainbows and P _max∝ wt for the moonies where t is the thickness of the rainbow or the thickness of the metal end cap of the moonie and w the thickness of the piezoelectric disk of the moonie. These predictions agree well with the experimental results found in the rainbows and the moonies. Our analysis showed that although the rainbows and the moonies differ in design and processing, the underlying physics for the enhancement in the axial displacement are essentially the same: The nonuniform distribution of d ₃₁ through the thickness of the transducer causes the transducer to arch or flatten with an applied electrical field, which leads to the enhancement in the axial displacement. The only difference is that, for the transducer to arch, the applied field is in the opposite direction to the polarization in the rainbows but in the same direction as the polarization in the moonies.     

Processing of Silicon Carbide-Mullite-Alumina Nanocomposites

Nanocomposite materials in the form of nanometer-sized second-phase particles dispersed in a ceramic matrix have been shown to display enhanced mechanical properties. In spite of this potential, processing methodologies to produce these nanocomposites are not well established. In this paper, we describe a new method for processing SiC-mullite-Al₂O₃ nanocomposites by the reaction sintering of green compacts prepared by colloidal consolidation of a mixture of SiC and Al₂O₃ powders. In this method, the surface of the SiC particles was first oxidized to produce silicon oxide and to reduce the core of the SiC particles to nanometer size. Next, the surface silicon oxide was reacted with alumina to produce mullite. This process results in particles with two kinds of morphologies: nanometer-sized SiC particles that are distributed in the mullite phase and mullite whiskers in the SiC phase. Both particle types are immersed in an Al₂O₃ matrix.     

Consolidation Behavior of Flocculated Alumina Suspensions

The consolidation behavior of flocculated alumina suspensions has been analyzed as a function of the interparticle energy. Consolidation was performed by a centrifugal force field or by gravity, and both the time-dependent and equilibrium density profiles were measured by a gamma-ray absorption technique. The interparicle energy at contact was controlled by adsorbing fatty acids of varying molecular weight at the alumina/decalin interface. We found that strongly attractive interactions result in a particle network which resists consolidation and shows compressible behavior over a large stress range. The most weakly flocculated suspension showed an essentially incompressible, homogeneous density profile after consolidation at different centrifugal speeds. We also found a significant variation in the maximum volume fraction, φ_m, obtained, with φ_m∼ 0.54 for the most strongly flocculated suspension to φ_m∼ 0.63 for the most weakly flocculated suspension. The compresive yield stresses show a behavior which can be fitted to a modified power law. In this paper, we discuss possible correlations between the fitting parameters and physical properties of the flocculated suspensions.     

Mullitization of Diphasic Aluminosilicate Gels

Recent studies have shown that the mullitization of diphasic aluminosilicate matrices comprising transitional alumina and amorphous silica occurs via a nucleation and growth process. Nucleation is preceded by a temperature-dependent incubation period. Following this incubation period, rapid nucleation of mullite occurs, producing about 1.8 × 10¹¹ nuclei/cm³, which remains constant throughout the rest of the transformation. Both incubation and mullite growth are thermally activated processes with apparent activation energies of 987 ± 63 and 1070 ± 200 kJ/mol, respectively. The growth rate of mullite grains under isothermal conditions is time dependent. An interpretation of these results is proposed on the basis of the nucleation and growth concepts of LaMer and Dinegar which supports the concept that the growth rate of mullite grains is controlled by the dissolution of transitional alumina into the amorphous matrix.     

Mullite for Structural, Electronic, and Optical Applications

Mullite (3Al₂O₃·2SiO₂) is becoming increasingly important in electronic, optical, and high-temperature structural applications. This paper reviews the current state of mullite-related research at a fundamental level, within the framework of phase equilibria, crystal structure, synthesis, processing, and properties. Phase equilibria are discussed in terms of the problems associated with the nucleation kinetics of mullite and the large variations observed in the solid-solution range. The incongruent melting behavior of mullite is now widely accepted. Large variations in the solid solubility from 58 to 76 mol% alumina are related to the ordering/disordering of oxygen vacancies and are strongly coupled with the method of synthesis used to form mullite. Similarly, reaction sequences which lead to the formation of mullite upon heating depend on the spatial scale at which the components are mixed. Mixing at the atomic level is useful for low-temperature (<1000°C) synthesis of mullite but not for low-temperature sintering. In contrast, precursors that are segregated are better suited for low-temperature (1250° to 1500°C) densification through viscous deformation. Flexural strength and creep resistance at elevated temperatures are significantly affected by the presence of glassy boundary inclusions; in the absence of glassy inclusions, polycrystalline mullite retains >90% of its room-temperature strength to 1500°C and displays very high creep resistance. Because of its low dielectric constant, mullite has now emerged as a substrate material in high-performance packaging applications. Interest in optical applications mainly centers on its applicability as a window material within the mid-infrared range.     

Generic visual analysis for multi- and hyperspectral image data

Multi- and hyperspectral imaging and data analysis has been investigated in the last decades in the context of various fields of application like remote sensing or microscopic spectroscopy. However, recent developments in sensor technology and a growing number of application areas require a more generic view on data analysis, that clearly expands the current, domain-specific approaches. In this context, we address the problem of interactive exploration of multi- and hyperspectral data, consisting of (semi-)automatic data analysis and scientific visualization in a comprehensive fashion. In this paper, we propose an approach that enables a generic interactive exploration and easy segmentation of multi- and hyperspectral data, based on characterizing spectra of an individual dataset, the so-called endmembers. Using the concepts of existing endmember extraction algorithms, we derive a visual analysis system, where the characteristic spectra initially identified serve as input to interactively tailor a problem-specific visual analysis by means of visual exploration. An optional outlier detection improves the robustness of the endmember detection and analysis. An adequate system feedback of the costly unmixing procedure for the spectral data with respect to the current set of endmembers is ensured by a novel technique for progressive unmixing and view update which is applied at user modification. The progressive unmixing is based on an efficient prediction scheme applied to previous unmixing results. We present a detailed evaluation of our system in terms of confocal Raman microscopy, common multispectral imaging and remote sensing.