An asymptotic maximum likelihood for estimating the nominal angle of a spatially distributed source

This paper proposes a large-sample approximation of the maximum-likelihood estimator for direction finding in the presence of a spatially spread source. The key idea is to replace the parametric estimate of the four-dimensional nuisance parameter vector with the approximate one that depends on just one parameter of interest, called the nominal angle, thus permitting the use of one-dimensional optimization techniques. The proposed estimator is shown to be strongly consistent and asymptotically efficient, and the Cramér–Rao bound on its standard deviation is derived. Simulations show the estimator to outperform previously proposed estimators, such as the subspace-based estimator and others based on one-dimensional search.     

Large-scale synthesis of WO3 nanoplates by a microwave-hydrothermal method

Tungsten oxide (WO₃) nanoplates were synthesized by a 270 W microwave-hydrothermal reaction of Na₂WO₄·2H₂O and citric acid (C₆H₈O₇·H₂O) in deionized water. X-ray diffraction (XRD), scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM), and selected area electron diffraction (SAED) were used to reveal the synthesis of WO₃ complete rectangular nanoplates in the solution of 0.2 g citric acid for 180 min, with O-W-O FTIR stretching modes at 819 and 741 cm⁻¹, and two prominent O-W-O Raman stretching modes at 804 and 713 cm⁻¹. The 2.71 eV indirect energy gap, and 430-460 nm blue emission wavelength range of WO₃ complete rectangular nanoplates were determined using UV-visible and photoluminescence (PL) spectrometers. The formation mechanism was also proposed according to the experimental results.     

Heat transfer enhancement and pressure drop characteristics of TiO2–water nanofluid in a double-tube counter flow heat exchanger

This article reports an experimental study on the forced convective heat transfer and flow characteristics of a nanofluid consisting of water and 0.2 vol.% TiO₂ nanoparticles. The heat transfer coefficient and friction factor of the TiO₂–water nanofluid flowing in a horizontal double-tube counter flow heat exchanger under turbulent flow conditions are investigated. The Degussa P25 TiO₂ nanoparticles of about 21 nm diameter are used in the present study. The results show that the convective heat transfer coefficient of nanofluid is slightly higher than that of the base liquid by about 6–11%. The heat transfer coefficient of the nanofluid increases with an increase in the mass flow rate of the hot water and nanofluid, and increases with a decrease in the nanofluid temperature, and the temperature of the heating fluid has no significant effect on the heat transfer coefficient of the nanofluid. It is also seen that the Gnielinski equation failed to predict the heat transfer coefficient of the nanofluid. Finally, the use of the nanofluid has a little penalty in pressure drop.     

Solid-state synthesis of cubic ZnTe nanocrystals using a microwave plasma

Cubic ZnTe nanocrystals were produced from 1:1 and 1.8:1 molar ratios of Zn:Te by a 900 W microwave plasma. The phase was detected using X-ray diffraction (XRD), which are in accordance with those of the simulations, and selected area electron diffraction (SAED). Raman spectroscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) showed that the products were nanocrystals with different orientations, including three longitudinal optical (LO) vibrations at 205, 410 and 620 cm^? 1 and a transverse optical (TO) vibration at 166 cm^? 1. Their green emissions were detected at 562 nm (2.21 eV) using luminescence spectrophotometry.     

Transient solid-state production of nanostructured CuS flowers

CuS (hcp) with different morphologies was produced using a transient solid-state reaction by the direct flow of electricity through solids, containing 1:1 molar ratio of Cu:S powders, in a high vacuum system for different lengths of time. X-ray diffraction (XRD), selected area electron diffraction (SAED), and scanning and transmission electron microscopies (SEM and TEM) specified that the products were nanostructured CuS flowers, and nanostructured CuS composing of nanoparticles with different orientations, controlled by the length of time. Raman vibrations were detected at 474.5 cm^− 1, and photoluminescent (PL) emissions at 347.5 nm. Both the XRD and SAED patterns are in accordance with those obtained by the corresponding simulations.     

A model of energy management analysis,case study of a sugar factory in Turkey

This study presents a case study of energy management in a sugar factory in Turkey. The main idea of the study is to analyse energy consumption, the quantity of material production, and figure out a suitable energy efficiency for the case study of a sugar factory subsequently. Firstly, a material production and energy consumption audit were performed for the sugar factory. Secondly, energy efficiency was calculated from the energy data. The SPSS (Statistical Package for the Social Sciences) statistical software was used to ensure the accuracy of the data. The factory’s energy consumption was calculated as 43,590.25 toe (tons of oil equivalent) over the last year. These results were used for CUSUM (Cumulative Sum Deviation Method) graphics. This research poses the consumption of energy, cost of energy and the relationship between energy usage and material production of sugar. The unit of energy cost was 688.22 [$/toe] for the last year. This result showed that the factory decreased the unit of energy by optimisation. The results indicated that the investigated sugar factory should pay attention to the energy management issue in order to comply with the Energy Efficiency of Turkish Law and Directives.     

Transformation of cubic AgBiS2 from nanoparticles to nanostructured flowers by a microwave-refluxing method

Cubic AgBiS₂ nanoparticles and flower-like clusters were successfully synthesized by microwave refluxing of CH₃COOAg, Bi(NO₃)₃·5H₂O and thiosemicarbazide (NH₂NHCSNH₂) in ethylene glycol. The phase was detected by X-ray diffraction (XRD) and selected area electron diffraction (SAED). The SAED pattern was also in accordance with that of the simulation. Scanning and transmission electron microscopy (SEM and TEM) revealed the gradual transformation of nanoparticles into flower-like clusters by increasing microwave power. Their UV–visible absorption and photoluminescence (PL) emission were detected by spectrometry. Possible formation mechanism of nanoparticles and nanostructured flowers was also proposed according to the experimental results.     

Oxidative Stress and Its Significant Roles in Neurodegenerative Diseases and Cancer

Reactive oxygen and nitrogen species have been implicated in diverse pathophysiological conditions, including inflammation, neurodegenerative diseases and cancer. Accumulating evidence indicates that oxidative damage to biomolecules including lipids, proteins and DNA, contributes to these diseases. Previous studies suggest roles of lipid peroxidation and oxysterols in the development of neurodegenerative diseases and inflammation-related cancer. Our recent studies identifying and characterizing carbonylated proteins reveal oxidative damage to heat shock proteins in neurodegenerative disease models and inflammation-related cancer, suggesting dysfunction in their antioxidative properties. In neurodegenerative diseases, DNA damage may not only play a role in the induction of apoptosis, but also may inhibit cellular division via telomere shortening. Immunohistochemical analyses showed co-localization of oxidative/nitrative DNA lesions and stemness markers in the cells of inflammation-related cancers. Here, we review oxidative stress and its significant roles in neurodegenerative diseases and cancer.     

Purification and Characterization of Organic Solvent and Detergent Tolerant Lipase from Thermotolerant Bacillus sp. RN2

The aim of this study was to characterize the organic solvent and detergent tolerant properties of recombinant lipase isolated from thermotolerant Bacillus sp. RN2 (Lip-SBRN2). The isolation of the lipase-coding gene was achieved by the use of inverse and direct PCR. The complete DNA sequencing of the gene revealed that the lip-SBRN2 gene contains 576 nucleotides which corresponded to 192 deduced amino acids. The purified enzyme was homogeneous with the estimated molecular mass of 19 kDa as determined by SDS-PAGE and gel filtration. The Lip-SBRN2 was stable in a pH range of 9-11 and temperature range of 45-60 °C. The enzyme was a non metallo-monomeric protein and was active against pNP-caprylate (C8) and pNP-laurate (C12) and coconut oil. The Lip-SBRN2 exhibited a high level of activity in the presence of 108% benzene, 102.4% diethylether and 112% SDS. It is anticipated that the organic solvent and detergent tolerant enzyme secreted by Bacillus sp. RN2 will be applicable as catalysts for reaction in the presence of organic solvents and detergents.     

Parametric study and optimization of a food can corrugation design using a response surface method

This paper presents the parametric design and functional optimization of a thin-walled food container with a corrugated surface. The configuration of the can corrugation should be designed to minimize the use of raw material subject to the constraints of the targeted structural performance. In the present study, the failure behaviors and the buckling strengths of a commercial food can under paneling pressure and axial loading are investigated with a series of experiments and finite element analyses. Full factorial design is implemented to study the effects of the geometric parameters of the corrugation (e.g., depth, radius, spacing and number of beadings) on its strength. Parameter optimization using a rotatable central composite design is employed to identify an optimal corrugation design by approximating the response surfaces of the can strength in terms of the significant design variables. The obtained surfaces are derived through the analysis of variance, and the suitability of the response is justified. A light- weight can body is then achieved by reduction of the can body thickness according to the required strength characteristics. Finite element analysis of the optimal model is also performed to confirm the predicted results. By using the proposed procedure, the can-body weight can be reduced by up to 12% compared with the original design.