Using the job-exposure matrix for elaborating job histories.

A first software (JHS) for the elaboration of job histories oriented toward risks was designed and results published In an article "A software for the elaboration of Job Histories". This article presents a second software (JES), based on the use of a job-exposure matrix designed for one company. The matrix is essentially a database, an organized gathering of information concerning the company. The two softwares are inter-faced and both run on a PC. When properly exploited, the two softwares can serve as an asset for epidemiological studies dealing with occupational health.     

Thin‐film encapsulated white organic light top‐emitting diodes using a WO3/Ag/WO3 cathode to enhance light out‐coupling

An alternative design of a semitransparent cathode for top‐emission white‐fluorescent organic light‐emitting diodes (OLEDs) has been investigated. The scope of this study was to improve the luminance of OLEDs used for displays while keeping the current density versus voltage characteristic unchanged for addressing purposes. The use of an optical simulation tool allowed the optimization of the tri‐layer cathode WO₃/Ag/WO₃ to increase the light out‐coupling coefficient of the device leading to an increased white emission compared with a reference device with a Ca/Ag cathode. An increase of ~40% in luminance has been calculated by simulation and experimentally confirmed. The p‐i‐n OLED structure underneath the tri‐layer cathode allowed an efficient injection of electrons independently from the work function of WO₃. The WO₃/Ag/WO₃ cathode has been also confirmed to be compatible with the atomic layer deposition technique for thin film encapsulation. Finally, lifetime measurements up to 600 h have been carried out to quantify the enhancements induced by the new cathode compared with the control device. It has been found that lifetimes of both cathode architectures are similar on this time scale, while the WO₃/Ag/WO₃ cathode shows a lower voltage drift versus aging.     

Energy Based 3D Autopilot for VTOL UAV Under Guidance & Navigation Constraints

Motion control design plays a crucial role in autonomous vehicles. Mainly, these systems operate in conditions of under-actuation, which make the control a serious task especially in presence of practical constraints. The main objective within this paper is to ensure the tracking of 3D reference trajectory overcoming some of the issues related to the control of multi-rotor vehicles (such as underactuation, robustness, limited power, accuracy, overshoot, etc.). Therefore, a control scheme for Vertical Take Off and Landing (VTOL) multi-rotor Unmanned Aerial Vehicle (UAV) is designed, applying the Interconnection and Damping Assignment-Passivity Based Control (IDA-PBC) technique. As reference model based technique, the control specifications are readily met by fixing a desired dynamic model, which is a major advantage of the technique. Moreover, a port ?controlled Hamiltonian representation is exploited in order to point out the physical properties of the system such as its internal energy. This latter is exploited, as a fitness function for an optimization algorithm, in order to decrease the consumed energy especially at the take-off step and allows the tuning of the controller parameters. The numerical simulations have shown satisfactory results that support the claims using nominal system model or disturbed model. The designed controller has been implemented on a real vehicle for which one demonstrates, in an indoor area manipulation, the effectiveness of the proposed control strategy.     

Use of Phosphate Rock for the Removal of Ni2+ from Aqueous Solutions: Kinetic and Thermodynamics Studies

A study was carried out in batch conditions to examine the removal of nickel ions from an aqueous solution by phosphate rock. The effect of different sorption parameters, such as initial metal concentration, equilibration time, solution pH, and temperature on the amount of Ni2+ sorbed was studied and discussed. The sorption process followed pseudo-second-order kinetics with necessary time of 2?h to reach equilibrium. The maximum removal obtained is at initial pH around 8. Nickel uptake was quantitatively evaluated using the Langmuir and Dubinin–Kaganer–Radushkevich model. The Langmuir adsorption isotherm constant corresponding to adsorption capacity, Q0, was found to be 7.63?mg/g. The possibility of metal recovery was investigated using several eluting agents. The desorbed amount of nickel decreased continuously with increasing pH, and increased with increasing Ca2+ concentration in leaching solution.     

Performance Tendency of Gain and Noise Figure at Different EDFA Configurations

A comprehensive behavioral investigation of gain and noise figure(NF) at different erbium doped fiber amplifier(EDFA) configurations is proposed.Configurations such as single pass(SP),single pass with filter(SPF),double pass(DP) and double pass with filter(DPF) are designed,investigated and compared.A continuous increasing of gain value is recorded by changing the configuration from SP to SPF to DP then to DPF.The NF value shows different behaviors at different configurations.     

An investigation of cutting forces in machining with worn ball-end mill

Reliable tool wear monitoring technique is one of the important aspects for achieving an integrated and self-adjusting manufacturing system. In this study, an analytical model is proposed to estimate the cutting forces, the tool geometry, and the chip geometry in relation to the flank wear, when milling with a ball-end mill. Modeling is based on thermomechanical modelling of oblique cutting. The worn tool geometry is decomposed into a series of axial elementary cutting edges. At any active tooth element, the flank wear geometry is calculated and the chip formation is obtained from an oblique cutting process characterised by local undeformed chip section and local cutting angles. Coated carbide ball-end tool, and a titanium workpiece material have been considered in this paper. The results found by using developed models have shown good agreement with experimental results.     

Cutting parameter optimization in NC milling

The continuous demand for higher productivity and product quality asks for better optimizing of the machining process. In this case, numerical controlled (NC) milling is a processing technology massively applied in the metal manufacturing industry; it has received very important interest in this century because it has a very high productivity and high work piece surface quality. The main objective of this work is to evaluate the machining time of different cycles, in 2.5?D NC milling. The prediction of the optimal values of cutting speed was analyzed to minimize both time and cost of die production. Optimum and economical values of cutting speed give, respectively, minimum production time and minimum production cost. An experimental study is carried out to validate machining time calculation models developed in this work. The cutting parameters analyzed in this study are cutting speed, feed per tooth, and the radial cutting depth.