Multimedia Systems - The preferences of Web information purchasers are changing. Cost-effectiveness (i.e., an emphasis on performance with respect to price) is becoming less regarded than... 相似文献
AbstractBuilding thermal inertia and operation control strategies have impacted on the thermal performance of a radiant floor heating system. This study conducts a two-dimensional numerical analysis of an intermittently operated radiant floor heating system using the Re-Normalization Group model with Discrete Ordinates Radiation model. A detailed numerical simulation setups and various analyses are provided, including grid independency analysis, initial condition, time step sizes and external boundary conditions. Three different weekend day intermittent operation strategies are investigated. The results showed that Case 3 designed with pre-heating of 20?h has better performance compared to Case 1 designed with pre-heating of 8?h and Case 2 designed with pre-heating of 14?h. The average indoor air temperature differences of approximate 2.1, 1.6 and 1.2 K are observed for Case 1, Case 2 and Case 3, respectively, when comparing two-time slot at 8:00am on Friday morning and Monday morning. This significantly highlights the effect of thermal inertia and the potential of energy saving due to the utilization of intermittent operation. Therefore, the current study presents numerical simulation potential in evaluating the radiant floor heating effects on indoor thermal environment, taking into account building thermal inertia and transient external climatic conditions. 相似文献
In the development of metal-organic frameworks (MOFs), secondary building units (SBUs) have been utilized as molecular modules for the construction of nanoporous materials with robust structures. Under solvothermal synthetic conditions, dynamic changes in the metal coordination environments and ligand coordination modes of SBUs determine the resultant product structures. Alternatively, MOF phases with new topologies can also be achieved by post-synthetic treatment of as-synthesized MOFs via the introduction of acidic or basic moieties that cause the simultaneous cleavage/reformation of coordination bonds in the solid state. In this sense, we studied the solid-state transformation of two ndc-based Zn-MOFs (ndc = 1,4-naphthalene dicarboxylate) with different SBUs but the same pcu topology to another MOF with sev topology. One of the chosen MOFs with pcu nets is [Zn2(ndc)2(bpy)]n (bpy = 4,4′-bipyridine), (6Cbpy-MOF) consisting of a 6-connected pillared-paddlewheel SBU, and the other is IRMOF-7 composed of 6-connected Zn4O(COO)6 SBUs and ndc. Upon post-structural modification, these pcu MOFs were converted into the same MOF with sev topology constructed from the uncommon 7-connected Zn4O(COO)7 SBU (7C-MOF). The appropriate post-synthetic conditions for the transformation of each SBUs were systematically examined. In addition, the effect of the pillar molecules in the pillared-paddlewheel MOFs on the topology conversion was studied in terms of the linker basicity, which determines the inertness during the solid-state phase transformation. This post-synthetic modification approach is expected to expand the available methods for designing and synthesizing MOFs with controlled topologies.
Metals and Materials International - This study investigated the influence of the initial grain size on the plastic deformation and tunnel defects that occurred from friction stir welding of... 相似文献
Advances in the fabrication of solid-solution single crystal relaxor ferroelectrics have made it possible to produce highly efficient piezoelectric crystals, and have attracted renewed interest in the use of these crystals for a new generation of piezoelectric transducers, actuators and sensors. Of particular interest is their incorporation into micro-electromechanical systems (MEMS). In this paper we report on the laser-induced wet chemical etching of lead zinc niobate-lead titanate (PZN-PT) in hydrochloric acid (HCl). Argon-ion laser radiation at power levels up to 4 W is focused to a spot diameter of about 15μm and results in the chemical etching of grooves at patterning speeds up to 5μm/sec. Crystal ion slicing, an ion-implant-based film separation technique, is used in combination with laser etching to form 5 to 10μm-thick patterned and freestanding films for incorporation into micro-electromechanical devices. 相似文献
Rice samples consumed by local populations were collected between 1990 and 1995 in 17 areas in the world, mostly from Asia (10 areas), but also from 7 areas outside of Asia. In total, 1528 samples were obtained (about one half from Japan) and were analyzed for lead (Pb) by electrothermal atomic absorption spectrometry. When the Pb contents in rice samples were classified into 10 areas in Asia, the highest and the lowest geometric means (GMs) were for Indonesia (38 ng/g) and Australia (2 ng/g), respectively. Among 7 regions outside Asia, the GM was highest for Spain (58 ng/g) and the lowest for the USA. (3 ng/g). Moreover, inter-regional differences were significant, when more than 100 samples from one area were divided into 3-9 regions and GMs for regions were compared. There was a marked difference in Pb contents in rice by areas and regions in the world. Nevertheless, comparison by area of the present results with those reported in literature show that there has been no substantial reduction in Pb in rice in the past decade either in Japan or elsewhere in the world. 相似文献
A 0.9 V third-order double-sampled delta-sigma audio ADC is presented. A new method using a combination of a switched-RC technique and a floating switched-capacitor double-sampling configuration enabled low-voltage operation without clock boosting or bootstrapping. A three-level quantizer with simple dynamic element matching was used to improve linearity. The prototype IC implemented in a 0.13 CMOS process achieves 92 dB DR, 91 dB SNR and 89 dB SNDR in a 24 kHz audio signal bandwidth, while consuming 1.5 mW from a 0.9 V supply. The prototype operates from 0.65 V to 1.5 V supply with minimal performance degradation. 相似文献
Due to their small size, mammalian oocytes and embryos pose unique problems during preparation for transmission electron microscopy. This paper outlines a method which combines protein embedding with centrifugation to locate the specimens on the face of a Beem capsule mould. This method facilitates both the processing of oocytes with minimal loss and rapid location of the specimens within the block for simultaneous sectioning, staining and examination. 相似文献
Multicomponent mass transfer accompanied by instantaneous chemical reactions in a small drop has been modeled and simulated
for the case where two different solutes diffuse from a continuous phase into the drop and react rapidly with a third reactant
in the drop. The computational results obtained by Galerkin’s finite element method are reported in terms of concentration
profiles, the locations of reaction front, the cumulative mass flux, and the enhancement factor. The effects of physical parameters,
such as diffusivities of the solutes and the reactant, the interfacial concentration of solutes, and the relative amount of
the reactant, on the calculated quantities are discussed. 相似文献