Temperature and pressure effects on supercritical CO2 extraction of tomato seed oil

Tomato seed oil was extracted with supercritical carbon dioxide in a semibatch-flow extractor within the temperature range 313–343 K and the pressure range 10.8–24.5MPa. The extraction rates increased with pressure, but decreased with temperature increase because of the variation in solvent density and resultant differences in oil solubility. The fatty acid composition of the extracted oil was similar to that of soybean oil.     

Doubly Bonded C60 Dimers and Congeners: Computational Studies of Structures, Bond Energies and Transformations

Initial steps of thermal transformation from doubly bonded [2+2] (1) and [4+4] (2) dimers of C₆₀ have been analyzed on the basis of computed structural features and Pople's energy partition scheme. Completely conjugated C₁₂₀ structures 3 and 4 are found to be considerably stable and proposed to be important intermediates. The linkage patterns in 3 and 4 are also likely to appear in the repeating units of the metastable dimer and polymer phases of A₁ crystals.     

d-Tubocurarine accentuates the burn-induced upregulation of nicotinic acetylcholine receptors at the muscle membrane

BACKGROUND: Increases in acetylcholine receptors (AChRs) at the muscle membrane, induced by burn injury, have been associated with a hyperkalemic response to succinylcholine and resistance to d-tubocurarine-like drugs. Muscle relaxants often are administered to burn-injured patients in the intensive care unit to facilitate mechanical ventilation. This study in rats tested whether continuous administration of d-tubocurarine in subparalytic doses exaggerates the upregulation of AChRs induced by burn trauma. Subparalytic doses were used to avoid the confounding effects of immobilization. METHODS: Three days after an approximate 50% body surface area burn or sham injury, the animals received an infusion of 3.03 +/- 0.05 micrograms/h of d-tubocurarine or equal volume of saline directly to the left gastrocnemius muscle via catheter connected to a subcutaneously implanted osmotic pump. After 7 days of d-tubocurarine or saline infusion, the AChRs were quantitated using 125I-alpha-bungarotoxin. The AChRs on the d-tubocurarine or saline-infused left gastrocnemius were compared to the contralateral gastrocnemius in the same group. The right or left gastrocnemius AChRs were compared to the ipsilateral muscles between groups. These intra- and intergroup comparisons allowed the delineation of the effects of catheter irritation, burns, or d-tubocurarine on AChRs. RESULTS: Daily examination of the withdrawal response to toe-pinch revealed no evidence of paralysis. Weight loss in the burn-injury animals receiving d-tubocurarine or saline was similar, confirming that the infusion of d-tubocurarine did not impair the mobility of the animals to move and feed. The plasma d-tubocurarine concentration after 7 days of infusion was 26.0 +/- 12 ng/ml (mean +/- SE). Regardless of burn or sham injury or of d-tubocurarine or saline infusion, the concentration of AChRs on the left was consistently greater than in the contralateral right gastrocnemius muscles within the same group, indicating that manipulation of the area alone can result in upregulation of AChRs. The AChRs in the right gastrocnemius of burn-injured animals were greater than those in the same muscle of sham-injured animals, regardless of saline (7.24 +/- 0.9 vs. 5.7 +/- 0.5 fmoles/mg protein, P = 0.06) or d-tubocurarine (7.3 +/- 0.4 vs. 5.7 +/- 0.5, P < 0.05) infusion to the burn-injury groups. AChRs in the left gastrocnemius of burn-injury animals receiving d-tubocurarine were significantly greater than those in burn- or sham-injury animals receiving saline (13.9 +/- 1.1 vs. 9.8 +/- 1.2 and 7.1 +/- 0.5 fmoles/mg protein, respectively, P < 0.05). CONCLUSIONS: Burn-induced upregulation of AChRs is accentuated by infusion of subparalytic doses of d-tubocurarine. Concomitant administration of d-tubocurarine to burn-injured patients may result in further exaggeration of the aberrant responses to neuromuscular relaxants.     

Temperature Profile of Anatase-TiO2Powder Compact during Microwave Heating

Anatase-TiO₂ cylindrical pellets were microwave sintered and partially transformed to rutile-TiO₂.The rutile concentration profile was determined as a function of location within the pellet. The rutile distribution in the microwavesintered pellets was different from that in pellets sintered by conventional fast firing. Temperature profiles within the pellets were estimated using the irreversible nature of the anatase-rutile transformation. The estimated temperature profile within each pellet was not uniform. In the axial direction, maximum temperature occurred in the middle of the pellet. In the radial direction, maximum temperature occurred at 1 mm below the surface of the cylinder wall. Analysis of the temperature profile indicated that, although heat flow occurred in the microwave-sintered pellet, the temperature profile did not change during a microwave exposure of 5–90 min.     

High-accuracy bench mark solutions to natural convection in a square cavity

A fourth-order high-accuracy finite difference method is presented for the bouyancy-driven flow in a square cavity with differentially heated vertical walls. The two bench mark solutions against which other solutions can be compared were obtained. The present solution is seemed to be accurate up to fifth decimal. The proposed scheme is stable and convergent for high Rayleigh number, and will be applicable to general problems involving flow and heat transfer, especially in three dimensions.List of symbols a thermal diffusivity - g gravitational acceleration - h mesh length in the x-direction - k time step - L side length of cavity - Pr Prandtl number - Ra Rayleigh number = gTL ³/a - t time - T _c, T _h surface temperatures (see Fig. 1a) - T temperature - T temperature difference = T _h - T _c - u, v velocity in the x and y directions, respectively - x, y coordinates - x, y mesh lengths in the x- and y-directions, respectively Greek symbols volumetric expansion coefficient - kinematic viscosity - stream function - vorticity     

The structure of acetylene flames for diamond synthesis

An acetylene flame was photographed with an SIT camera through optical filters, and the signals were Abel transformed to obtain two-dimensional emission-intensity profiles. It was found that the intensive emissions of CH* and C*₂ are localized at the feather boundary, while the OH* emission is localized at the intermediate zone. The structure of the acetylene flame was made clear: it consists of a carbon-radical-rich feather and an oxygen-radical-rich intermediate zone. The carbon-radical concentrations are approximately in equilibrium near the burner exit while they decrease almost linearly via interdiffusion and reactions with the oxygen-radicals in the intermediate zone.Numerical simulations including detailed gaseous and surface reactions reproduced well previous preliminary calculations showing that CH₄ is rapidly produced in the boundary layer near the substrate followed by an increase in CH₃. This result satisfactorily explains the measured dependence of growth rate on the substrate temperature and ratio.     

Microstructures and magnetic properties of heatproof domain-refined grain-oriented silicon steel sheets

Microstructures and magnetic properties of heatproof domain- refined grain- oriented silicon steel sheets were studied. Local strains were introduced using two types of gear roll as well as cog tips, one 35 Μm and the other 85 Μm. After the local strains were introduced onto sheets, the distribution of hardness near the groove was measured. The nuclei of micrograins were investigated at various applied rolling loads. After stress-relief annealing, various shapes of microgranes and grooves were observed. The effect of these various shapes of grooves and micrograins on magnetic properties was clarified. The role of micrograins and grooves on domain refining is discussed.     

A new refining process for iron oxide using iron ore and its application to hard ferrites

Kawasaki Steel Corporation and Kawatetsu Mining Co., Ltd. have developed a new refining process to extract iron oxide from iron ore to meet the increase in demand for iron oxide for high- grade hard ferrites. This article discusses the quality of iron oxides and the characteristics of the hard ferrite magnets produced from them.