A STUDY OF THE FLOTATION OF OXIDIZED AHASRA COAL

The flotation of oxidized Amasra Coal which was collected between 1973-1978 and, stored in the atmospheric conditions was examined In this work. Coal samples were fractioned by wet screening to +0.560 mm, -0.500 + 0.140 mm, -0.140 mm particle sizes and first fraction was ground to -0.560 mm before flotation. Motorin and pine oil which had been heated at 125° C for 5 hours were used ns flotation reagents. The influence of impeller speed, aeration rate, solid concent of the pulp, reagent amounts were examined and optimum values were determined. Increase of the pine oil amount added to the pulp, increased the coal. recovery on the flotation of this oxidized coal.     

Subsurface Characterization at Ground Failure Sites in Adapazari, Turkey

Ground failure in Adapazari, Turkey during the 1999 Kocaeli earthquake was severe. Hundreds of structures settled, slid, tilted, and collapsed due in part to liquefaction and ground softening. Ground failure was more severe adjacent to and under buildings. The soils that led to severe building damage were generally low plasticity silts. In this paper, the results of a comprehensive investigation of the soils of Adapazari, which included cone penetration test (CPT) profiles followed by borings with standard penetration tests (SPTs) and soil index tests, are presented. The effects of subsurface conditions on the occurrence of ground failure and its resulting effect on building performance are explored through representative case histories. CPT- and SPT-based liquefaction triggering procedures adequately identified soils that liquefied if the clay-size criterion of the Chinese criteria was disregarded. The CPT was able to identify thin seams of loose liquefiable silt, and the SPT (with retrieved samples) allowed for reliable evaluation of the liquefaction susceptibility of fine-grained soils. A well-documented database of in situ and index testing is now available for incorporating in future CPT- and SPT-based liquefaction triggering correlations.     

Induced-charge electro-osmosis of polymer-containing fluid around a metallic rod

Induced-charge electro-osmotic (ICEO) flow of polymer-containing electrolyte solution around a cylindrical gold-coated stainless steel rod under AC electric field is measured by micro-particle image velocimetry (micro-PIV) for the first time. The ICEO flows as functions of the amount of non-ionic PEG (polyethylene glycol), cationic PDADMA (polydiallyldimethylammonium chloride), and anionic PVSASS (polyvinylsulfonic acid sodium salt) polymers added into the salt solution, frequency, and strength of the AC electric field are measured. The ICEO flow of polymer-containing fluid around the rod is quadrupolar with four vortices and is proportional to the square of imposed electric field. The ICEO flow velocity exponentially decreases with an increased concentration of neutral PEG. Ionic polyelectrolytes significantly increase ICEO velocities due to the enriched net charge within the induced electric double layer arising from the electrostatic interaction between the polarized rod’s surface and the charged polyelectrolytes in ionic polymer solution. In addition, polymer concentration affects the dependence of the ICEO flow on the frequency of AC electric field.     

Micro-PIV measurements of induced-charge electro-osmosis around a metal rod

A cylindrical gold-coated stainless steel rod was positioned at the center of a straight microchannel connecting two fluid reservoirs on either end. The microchannel was filled with 1 mM KCl containing 0.5 μm diameter carboxylate-modified spherical particles. Induced-charge electro-osmotic (ICEO) flow occurred around the metallic rod under a sinusoidal AC electric field applied using two platinum electrodes. The ICEO flows around the metallic rod were measured using micro particle image velocimetry (micro-PIV) technique as functions of the AC electric field strength and frequency. The present study provides experimental data about ICEO flow in the weakly nonlinear limit of thin double layers, in which, the charging dynamics of the double layer cannot be presented analytically. The measured ICEO flow pattern qualitatively agrees with the theoretical results obtained by Squires and Bazant (J Fluid Mech 509:217–252, 2004). Flow around the rod is quadrupolar, driving liquid towards the rod along the electric field and forcing it away from the rod in the direction perpendicular to the imposed electric field. The measured ICEO flow velocity is proportional to the square of the electric field strength, and depends on the applied AC frequency.     

Modelling of residual stresses in the shot peened material C-1020 by artificial neural network

This study consists of two cases: (i) The experimental analysis: Shot peening is a method to improve the resistance of metal pieces to fatigue by creating regions of residual stress. In this study, the residual stresses induced in steel specimen type C-1020 by applying various strengths of shot peening, are investigated using the electrochemical layer removal method. The best result is obtained using 0.26 mm A peening strength and the stress encountered in the shot peened material is ?276 MPa, while the maximum residual stress obtained is ?363 MPa at a peening strength of 0.43 mm A. (ii) The mathematical modelling analysis: The use of ANN has been proposed to determine the residual stresses based on various strengths of shot peening using results of experimental analysis. The back-propagation learning algorithm with two different variants and logistic sigmoid transfer function were used in the network. In order to train the neural network, limited experimental measurements were used as training and test data. The best fitting training data set was obtained with four neurons in the hidden layer, which made it possible to predict residual stress with accuracy at least as good as that of the experimental error, over the whole experimental range. After training, it was found the R² values are 0.996112 and 0.99896 for annealed before peening and shot peened only, respectively. Similarly, these values for testing data are 0.995858 and 0.999143, respectively. As seen from the results of mathematical modelling, the calculated residual stresses are obviously within acceptable uncertainties.     

Continuous Airborne Communication Relay Approach Using Unmanned Aerial Vehicles

As a result of unmanned aerial vehicles being widely used in different areas, studies about increasing the autonomous capabilities of unmanned aerial vehicles are gaining momentum. Today, unmanned aerial vehicle platforms are especially used in reconnaissance, surveillance and communications areas. In this study, in order to achieve continuous long-range communication relay infrastructure, artificial potential field based path planning of Unmanned Aerial Vehicles is discussed. A novel dynamic approach to relay-chain concept is proposed to maintain the communication between vehicles. Besides dynamically keeping vehicles in range and appropriate position to maintain communication relay, artificial potential field based path planning also provides collision avoidance system. The performance of the proposed system is measured by applying a simulation under the Matlab Simulink and Network Simulator environment. Artificial potential field based flight patterns are generated in Matlab, and performance of the communication between vehicles is measured in Network Simulation environment. Finally the simulation results show that an airborne communication relay can be established autonomously by using artificial potential filed based autonomous path planning approach. Continues state communication is provided by obtaining a resistant communication relay which depends on artificial potential field based positioning algorithm.     

Chemical and microbiological status and volatile profiles of mouldy Civil cheese,a Turkish mould‐ripened variety

The objective of this study is to characterise the gross chemical and microbiological status and identify the volatile compounds of mouldy Civil cheeses. A total of forty‐one samples were surveyed, and gross compositional status of the cheeses was (as mean values): 6.5 for pH, 6.2% for fat‐in‐dry matter, 51.8% for moisture and 15.3% for water‐soluble nitrogen (as% of total nitrogen). Chemical composition of the cheese samples varied widely. Mouldy Civil cheese has similar pH values and moisture contents when compared with blue‐type cheeses, but it has distinct feature for fat contents. The microbiological counts of the samples were found to be high and some samples contained coliform bacteria. A total of 95 volatiles, including esters (28), acids (6), ketones (12), aldehydes (3), alcohols (15), terpenes (10), sulphur compounds (3) and miscellaneous (18), were identified in the volatile fractions of the cheeses, and principal volatile groups were esters, alcohols and ketones.     

CFD for incompressible flows at NASA Ames

Over the past 30 years, numerical methods and simulation tools for incompressible flows have been advanced as a subset of the computational fluid dynamics (CFD) discipline. Although incompressible flows are encountered in many areas of engineering, the simulation of compressible flows has driven most of the development of computational algorithms and tools at NASA Ames Research Center. This is due to the stringent requirements for predicting aerodynamic performances of flight vehicles. Conversely, low-speed incompressible flow through or past flow devices did not require the same numerical accuracy. This practice of tolerating relatively low-fidelity solutions in engineering applications has changed, as the design of low-speed flow devices have become more sophisticated, along with more strict efficiency requirements. Accurate and robust CFD tools have become increasingly important in fluid engineering for incompressible and low-speed flow. This paper reviews advances in computational technologies for incompressible flow simulation developed at Ames, and some engineering successes brought about by these advances made during the same period. Additionally, some of the current challenges faced in computing incompressible flows are presented.