The recovery and recrystallization of cold rolled V-W-Ti alloys

Several V-W-Ti alloys with about 50% reduction in thickness by cold rolling were isochronally annealed at temperatures from 100 to 1100 °C. Hardness was measured after the annealing. By comparison with V4Cr4Ti and V4Ti alloys, the V6WTi alloy was found to begin recovery at a temperature about 100 °C higher, while the full recrystallization temperature was around 900 °C for all of the alloys. Hardness decreased successively above 500 °C in V8W, as is the case in pure V. Impurity induced hardening was observed around 300 °C only in the alloys without Ti. Precipitation and the interaction between interstitial impurities and dislocations were supposed to be the main contributors to the different recovery and recrystallization behaviors of the alloys.     

Research and Development of the Coprecipitation Process for Lanthanum Germanate Oxyapatite

Although lanthanum germanate oxyapatite (La–Ge–O) has shown good potential for use as a solid electrolyte in energy storage applications, its synthesis has been challenging by either solid‐ or solution‐state methods. In this study, a new synthesis of La–Ge–O was developed through a coprecipitation technique, in which a highly concentrated homogeneous aqueous solution of La and Ge was prepared from aqueous ammonium germanate and lanthanum nitrate solutions with the addition of dilute nitric acid. Several precipitates were formed by pH manipulation, including an amorphous material obtained at pH > 3. Compared to the individual precipitation behaviors of the parent compounds, the amorphous precipitate was formed only from the aqueous two‐component mixture, and appeared to contain both metals. This material was transformed into crystalline mixtures upon heating at 1273 K. The crystalline phases were La₂Ge₃O₉ and hexagonal‐type GeO₂ when the precipitate was formed below pH 8, and the La–Ge–O and La₂Ge₂O₇ phases when the precipitate was formed around pH 8. Product formation from the coprecipitate was discussed based on X‐ray diffraction and thermal analyses. The improved availability of La–Ge–O will allow more extensive investigations of its useful properties.     

Thermosetting bismaleimide resins generating covalent and multiple hydrogen bonds

Prepolymerizations of 4,4′‐bismaleimidodiphenylmethane (BMI), diallyl isocyanurate (DAIC), and melamine (ML) at 160–170°C and subsequent compression molding at 200–280°C yielded cured BMI/DAIC/ML resins with feed molar ratios of 4/1/1, 3/1/1, and 2/1/1 (BMI‐DAIC‐ML411, 311, and 211). Similarly, cured BMI/DAIC 1/1 and BMI/ML 3/1 resins (BMI‐DAIC11 and BMI‐ML31) were prepared. The FT‐IR analysis revealed that the maleimide and allyl groups were almost consumed for all the cured resins, and the hydrogen bonding interaction became stronger with decreasing BMI contents for BMI‐DAIC‐MLs. Based on the cured structures elucidated from the FT‐IR result, the numbers of multiple hydrogen bonds and cross‐linking covalent bonds (N_MHB and N_CB), and total cross‐linking bond energy (E_TB) were evaluated to be 0, 7.92, and 618 for BMI‐DAIC‐ML411, 0.71, 7.81, and 627 for BMI‐DAIC‐ML311, and 0.95 mol kg^?1, 7.61 mol kg^?1, and 617 kcal kg^?1 for BMI‐DAIC‐ML211, respectively. A higher order of glass transition and 5% weight loss temperatures for BMI‐DAIC‐MLs was 411 > 311 > 211 in accordance with a higher order of N_CB. BMI‐DAIC‐MLs displayed a weak tan δ peak at 70–150°C due to dissociation of the hydrogen bonds. The flexural strength and modulus of BMI‐DAIC‐ML311 were higher than those of BMI‐DAIC‐ML411 in accordance with the difference of E_TB. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43121.     

LiErO2 formation on Er2O3 in static and natural convection lithium

Er₂O₃ is candidate material for insulating coating to prevent the magnetohydrodynamic (MHD) pressure drop in the self-cooled liquid Li blanket system. Although Er₂O₃ is stable material, detailed chemical behavior in liquid Li is not clear. Corrosion behavior of bulk Er₂O₃ in Li is investigated in static and flowing condition in the present study. After these tests, good compatibility of Er₂O₃ was confirmed and slight formation of LiErO₂ was detected by XRD analysis. This chemical behavior did not change in a static and flowing tests, however some of the corrosion product of LiErO₂ was removed easily by the Li flow. Intensity of LiErO₂ peaks in XRD spectrum suggests that the temperature gradient may affect the reaction rate in the natural convection loop. Since corrosion rate of Er₂O₃ is very small, slight change in state will be important information to evaluate lifetime of coating.     

Corrosion characteristics of reduced activation ferritic steel, JLF-1 (8.92Cr–2W) in molten salts Flibe and Flinak

Static corrosion tests were performed in molten salts, LiF–BeF₂ (Flibe) and LiF–NaF–KF (Flinak), at 500 °C and 600 °C for 1000 h. The purpose is to investigate the corrosion characteristics of reduced activation ferritic steels, JLF-1 (8.92Cr–2W) in the fluids. The concentration of hydrogen fluoride (HF) in the fluids was measured by slurry pH titration method before and after the exposure. The HF concentration determined the fluoridation potential. The corrosion was mainly caused by dissolution of Fe and Cr into the fluids due to fluoridation and/or electrochemical corrosion. Carbon on the surface might be dissolved into the fluids due to the corrosion, and this resulted to the decrease of carbide on the surface. The corrosion depth of the JLF-1 specimen, which was obtained from the weight losses, was 0.637 μm in Flibe at 600 °C and 6.73 μm in Flinak at 600 °C.     

Growth of β-FeSi2 thin films on β-FeSi2 (110) substrates by molecular beam epitaxy

We have investigated the preparation of β-FeSi₂ substrate and growth condition of β-FeSi₂ thin film on β-FeSi₂ (110) substrate by molecular beam epitaxy. The surface of the substrate was prepared by a wet-etching using HF(50%):HNO₃(60%):H₂O = 1:1:5 solution at 25 °C. It is clear that the optimal etching period to obtain a flat surface was 3 min. The β-FeSi₂ thin film with streak RHEED pattern was obtained at Si/Fe flux ratio of 2.9. Average surface roughness (Ra) of the β-FeSi₂ film was about 0.5 nm in 5 × 5 μm² area.     

Metabolic Activation of Heterocyclic Amines and Expression of Xenobiotic‐Metabolizing Enzymes in the Gastrointestinal Tract of Rats

Heterocyclic amines get entry into human body mainly through ingestion of pan‐fried meats cooked at high temperatures. Exposure of the gastrointestinal tract (GIT) to ingested xenobiotics prior to delivery to the liver may lead to metabolic activation, which may explain the high incidence of GIT carcinogenesis. Therefore, this study investigated the mutagenic activation of 2 heterocyclic amines, 2‐aminoanthracene (2‐AA) and 3‐amino‐1‐methyl‐5H‐prydo[4,3‐b]indole (Trp‐P‐2), in the GIT of rats. In addition, the constitutive mRNA expression profiles of xenobiotic‐metabolizing enzymes (XMEs) in the GIT of rats were examined. Metabolic activation of 2‐AA was detected in all GIT tissues except the duodenum and rectum, and it was detected at high levels in the ileum and cecum. Furthermore, we revealed high metabolic activation of 2‐AA and Trp‐P‐2 in the jejunum. The mRNA expression of phase I and II enzymes in rat GIT corresponded with their mutagenic activation ability. In conclusion, our results suggest that different expression levels of XME among GIT tissues may contribute to the tissue‐specific differences in metabolic activation of xenobiotics such as heterocyclic amines in rats.     

Overview of the TITAN project

This is an overview paper of the joint TITAN (Tritium, Irradiation, and Thermofluid for America and Nippon) project of the Japan–USA fusion cooperation program. The objectives, tasks structure, and technical highlights of the TITAN project are presented, as well as the direction of the project toward its end in March 2013.