CNSL: an environment friendly alternative for the modern coating industry

Considering ecological and economical issues in the new generation coating industries, the maximum utilization of naturally occurring materials for polymer synthesis can be an obvious option. In the same line, one of the promising candidates for substituting partially, and to some extent totally, petroleum-based raw materials with an equivalent or even enhanced performance properties, is the Cashew Nut Shell Liquid (CNSL). This dark brown-colored viscous liquid obtained from shells of the cashew nut can be utilized for a number of polymerization reactions due to its reactive phenolic structure and a meta-substituted unsaturated aliphatic chain. Therefore, a wide variety of resins can be synthesized from CNSL, such as polyesters, phenolic resins, epoxy resins, polyurethanes, acrylics, vinyl, alkyds, etc. The present article discusses the potential of CNSL and its derivatives as an environment friendly alternative for petroleum-based raw materials as far as polymer and coating industries are concerned.     

Benzyl ester of dehydrated castor oil fatty acid as plasticizer for poly(vinyl chloride)

The poly(vinyl chloride) (PVC) industry plays an important role in today's total plastics industry. The major volume of PVC is used as soft and plasticized PVC. PVC applications consume approximately 80% of the total production of plasticizers. Most of the common plasticizers are aromatic esters of phthalic acid. In the majority of countries, phthalate plasticizers are banned due to their carcinogenic properties. The concern raised about toxicity led to a large demand for bio‐based non‐toxic plasticizers. Hence, there is an increasing interest in replacing the phthalate plasticizers with those produced from simple bio‐based materials. Dehydrated castor oil fatty acid (DCOFA) is a renewable resource which can be esterified and used as an environment friendly plasticizer for PVC. Benzyl ester (BE) was prepared by reacting DCOFA with benzyl alcohol in the presence of catalyst at 170–180 °C. Esterification was further confirmed by acid value, hydroxyl number, ¹H NMR and Fourier transform IR spectroscopy. The modified plasticizer was used in various proportions as a co‐plasticizer in PVC for partial replacement of dioctyl phthalate (DOP). With an increase in the proportion of BE in PVC samples, a good plasticizing performance was observed. The incorporation of BE also resulted in a reduction in viscosity and viscosity pick‐up and improved mechanical, exudation, thermal degradation and chemical resistance properties. The presence of BE showed a reduction in the whiteness index due to presence of conjugated double bonds in the structure. The results of DSC, XRD and Shore hardness studies showed no significant variation in properties compared with those of DOP‐plasticized sheets and thus we can conclude that BE can be used as a co‐plasticizer in PVC. © 2013 Society of Chemical Industry     

Study of Formulation Variables on Properties of Drug-Gellan Beads by Factorial Design

ABSTRACT

The aim of the present study was to obtain cross-linked calcium-gellan beads containing diclofenac sodium as model drug, using full 3³ factorial design. Drug quantity, pH of cross-linking solution, and speed of agitation were selected as variables for factorial design. The resultant beads were evaluated by scanning electron microscopy (SEM), percent yield, entrapment efficiency, micromeritic properties, swelling and drug release studies. The drug-loaded beads were spherical with size range of 0.85–1.8 mm. Percent yield and entrapment efficiency of various batches were in the range of 86.48–98.28% w/w and 72.52–92.74% w/w, respectively. Calcium-gellan beads containing diclofenac sodium showed pH-dependent swelling and drug release properties. Swelling and drug release were significantly higher in pH 7.4 phosphate buffer than 0.1N HCl. The swelling ratio for beads was up to 22 and 3 for phosphate buffer and 0.1N HCl, respectively. Cumulative diclofenac sodium release from calcium-gellan beads was 12–35% in 0.1N HCl within 2 h, whereas complete drug release was observed within 3–4 h in pH 7.4 phosphate buffer.     

FT-IR studies on the evolution of different phases and their interaction in ferric molybdate—molybdenum trioxide catalysts

Two samples of Fe–Mo catalysts have been prepared from ferric nitrate and ammonium paramolybdate, one following a conventional procedure and the other by a new precipitation procedure in a buffer medium. The evolution of different Fe–Mo phases, from the fresh precipitate to the aged and then to the calcined state, has been followed by FT-IR spectroscopy. All the spectral vibrations have been related to different coordination spheres of Mo and Fe ions in the samples and a comparison with a commercial catalyst of similar composition has been made. The new preparation procedure leads to small, uniform (0·3 μm size) particles and a homogeneous morphology of phases as seen by scanning electron microscopy. Additionally, a higher surface area (10·3 m² g^?1), lower bulk density (0·66 g cm^?3), a methanol conversion efficiency of > 90% and an HCHO selectivity of 95% distinguish this sample from the conventionally prepared one. Better thermal stability of this sample is inferred from the IR spectral and XRD analyses of the heat-treated (up to 800°C) samples and is related to the interaction between Fe₂(MoO₄)₃ and MoO₃ phases.     

Novel aspects of wet milling for the production of microsuspensions and nanosuspensions of poorly water-soluble drugs

Micronization and nanoparticle production of poorly water-soluble drugs was investigated using single wet milling equipment operating in the attritor and stirred media modes. The drug particles in the median size range of 0.2?2??m were prepared by changing the milling mode and operating conditions of a Micros mill with a purpose of elucidating the dynamics of the wet milling process. It was determined that particle breakage due to mechanical stresses and aggregation due to insufficient stabilization are two competing mechanisms which together control the wet milling dynamics of the poorly water-soluble drugs. The study in the attritor mode using four different classes of stabilizers with six drugs indicated that steric stabilization worked better than electrostatic stabilization for the drugs studied. In addition, the existence of different minimum polymer concentrations for the stabilization of microsuspensions and nanosuspensions was indicated. The major role of a non-ionic polymer during the production of fine particles is its stabilization action through steric effects, and no experimental evidence was found to support the so-called Rehbinder effect. Periodic addition of the polymer as opposed to the addition of the polymer at the start of milling process was introduced as a novel processing method. This novel method of polymer addition provided effective stabilization and breakage of drug particles leading to a narrower and finer particle size distribution. Alternatively, it may allow shorter processing time and lower overall power consumption of the milling process for a desired particle size.     

Soy protein supplementation does not cause lymphocytopenia in postmenopausal women

Background  

The health benefits of soy isoflavones have been widely investigated; however, there are some concerns as to whether soy isoflavones, similar to ipriflavone, a synthetic isoflavone, cause lymphocytopenia in postmenopausal women. Hence, the purpose of this study was to investigate the extent to which 12-month supplementation of 25 g soy protein containing 60 mg isoflavones alters lymphocyte counts or other hematological parameters in postmenopausal women who were not on hormone replacement therapy.     

Glycolytic depolymerization of PET waste using MP-diol and utilization of recycled product for UV-curable wood coating

Polyethylene terephthalate (PET) waste recycling has become a worldwide research interest for industries and academic institutes due its inevitable environmental impact. The main objective of current research work is to target efficient recycling of PET waste from mineral water bottles by the glycolysis method and subsequent use of the recycled product for value-added coating application. In the present study, we report on MP-diol (2-methyl-1,3-propanediol) which is not explored much for the chemical recycling of PET, having a branched aliphatic diol with two primary hydroxyls, for glycolysis reaction. The reaction parameters were optimized for microwave-assisted technique by varying the ratio of raw materials, reaction time, temperature, and power. The reaction parameters were optimized, and the recycled oligomeric product (OPETMPD) was separated, purified, and characterized by chemical and spectroscopic methods. Subsequently, dimethacrylated oligoesters of PET oligomer (UV oligomer) were synthesized by methacrylation of the glycolyzed PET product (OPETMPD). The synthesized UV oligomer was evaluated using chemical and spectroscopic methods. Ultraviolet (UV) radiation-curable formulations were prepared using synthesized UV oligomer and applied on wooden panels. The coatings were cured using UV-curing machine and evaluated for their performance properties. The partial replacement of UV oligomer in UV formulations exhibited comparative coating performance properties with respect to conventional UV formulation.     

Study of formulation variables on properties of drug-gellan beads by factorial design

The aim of the present study was to obtain cross-linked calcium-gellan beads containing diclofenac sodium as model drug, using full 3(3) factorial design. Drug quantity, pH of cross-linking solution, and speed of agitation were selected as variables for factorial design. The resultant beads were evaluated by scanning electron microscopy (SEM), percent yield, entrapment efficiency, micromeritic properties, swelling and drug release studies. The drug-loaded beads were spherical with size range of 0.85-1.8 mm. Percent yield and entrapment efficiency of various batches were in the range of 86.48-98.28% w/w and 72.52-92.74% w/w, respectively. Calcium-gellan beads containing diclofenac sodium showed pH-dependent swelling and drug release properties. Swelling and drug release were significantly higher in pH 7.4 phosphate buffer than 0.1N HCl. The swelling ratio for beads was up to 22 and 3 for phosphate buffer and 0.1N HCl, respectively. Cumulative diclofenac sodium release from calcium-gellan beads was 12-35% in 0.1N HCl within 2 h, whereas complete drug release was observed within 3-4 h in pH 7.4 phosphate buffer.     

Analysis of Drought from Humid,Semi-Arid and Arid Regions of India Using DrinC Model with Different Drought Indices

The study aims at evaluating the various drought indices for the humid, semi-arid and arid regions of India using conventional indices, such as rainfall anomaly index, departure analysis of rainfall and other indices such as Standard Precipitation Index (SPI) and Reconnaissance Drought Index (RDI) that were analyzed using the DrinC software. In SPI, arid region has seven drought years, whereas humid and semi-arid regions have four. In case of RDI, the humid and semi-arid regions have 11 drought years, whereas arid regions have 10 years. The difference in SPI and RDI was due to the fact that RDI considered potential evapotranspiration, and hence, correlation with plants would be better in case of RDI. Humid region showed a decreasing trend in initial value of RDI during the drought as compared to semiarid and arid regions and indicated possible climate change impact in these regions. Among all the indices, RDI was considered as an effective indicator because of implicit severity and high prediction matches with the actual drought years. SPI and RDI were found to be well correlated with respect to 3 months rainfall data and SPI values led to prediction of annual RDI. The results of our study established that this correlation could be used for developing disaster management plan well in advance to combat the drought consequences.