Analysis of stepwise charging limits and its implementation for efficiency improvement in switched capacitor DC–DC converters

In this work we analysed the stepwise charging technique to find the limits from which it is beneficial in terms of load capacitance and charge–discharge frequency. We included in the analysis practical limitations such as the consumption of auxiliary logic needed to implement the technique and the minimum size of auxiliary switches imposed by the technology. We proposed an ultra-low-power logic block to push these limits and to obtain benefits from this technique in small capacitances. Finally, we proposed to use a stepwise driver in the driving of the gate capacitance of power switches in switched-capacitor (SC) DC–DC converters. We designed and manufactured, in a 130 nm process, a SC DC–DC converter and measured a 29% energy reduction in the gate-drive losses of the converter. This accounts for an improvement of 4% (from 69 to 73%) in the overall converter efficiency.

     

An integrated dimensionality reduction and surrogate optimization approach for plant-wide chemical process operation

With liquefied natural gas becoming increasingly prevalent as a flexible source of energy, the design and optimization of industrial refrigeration cycles becomes even more important. In this article, we propose an integrated surrogate modeling and optimization framework to model and optimize the complex CryoMan Cascade refrigeration cycle. Dimensionality reduction techniques are used to reduce the large number of process decision variables which are subsequently supplied to an array of Gaussian processes, modeling both the process objective as well as feasibility constraints. Through iterative resampling of the rigorous model, this data-driven surrogate is continually refined and subsequently optimized. This approach was not only able to improve on the results of directly optimizing the process flow sheet but also located the set of optimal operating conditions in only 2 h as opposed to the original 3 weeks, facilitating its use in the operational optimization and enhanced process design of large-scale industrial chemical systems.     

Corrosion behavior of T24, T92, VM12, and AISI 304 steels exposed to KCl–NaCl–K2SO4–Na2SO4 salt mixtures

The corrosion mechanisms of T24, T92, VM12, and AISI 304 steels are studied under the influence of NaCl–KCl, NaCl–Na₂SO₄, and KCl–K₂SO₄ salt mixtures in a dry air atmosphere at 650°C for 15 days. NaCl–KCl was the most aggressive deposit and AISI 304 stainless steel exhibited the highest corrosion resistance. There was no relation between the Cr content of the ferritic steels and their corrosion resistance in NaCl–KCl. In contrast, the resistance of high-Cr steels was better when exposed to NaCl–Na₂SO₄ and KCl–K₂SO₄. The high-Cr and the low-Cr steels were more susceptible to NaCl–Na₂SO₄ and to KCl–K₂SO₄, respectively.     

Fat Distribution and Lipid Profile of Young Adults with Congenital Adrenal Hyperplasia Due to 21-Hydroxylase Enzyme Deficiency

We aimed to compare detailed fat distribution and lipid profile between young adults with congenital adrenal hyperplasia due to 21-hydroxylase enzyme deficiency and a control group. We also verified independent associations of treatment duration and daily hydrocortisone dose equivalent (HDE) with lipid profile within patients. This case–control study included 23 patients (7 male and 16 female) matched by an age range of young adults (18–31 years) with 20 control subjects (8 male and 12 female). Dual energy X-ray absorptiometry was used to measure the fat distribution. Male patients demonstrated elevated indices of fat mass for total (7.7 ± 2.1 vs. 4.5 ± 1.3 kg/m², p = 0.003), trunk (4.0 ± 1.2 vs. 2.2 ± 0.8 kg/m², p = 0.005), android (0.63 ± 0.24 vs. 0.32 ± 0.15 kg/m², p = 0.008), gynoid (1.34 ± 0.43 vs. 0.74 ± 0.24 kg/m², p = 0.005), arm (0.65 ± 0.16 vs. 0.39 ± 0.10 kg/m², p = 0.009), and leg regions (2.7 ± 0.8 vs. 1.6 ± 0.4 kg/m², p = 0.005) than the control group, but not in females. However, female patients demonstrated elevated ratio of low-density lipoprotein cholesterol to high-density lipoprotein cholesterol (1.90 ± 0.46 vs. 1.39 ± 0.47, p = 0.009) than the control group, but not in males. Total fat mass was inversely correlated with total testosterone (r = −0.64, p = 0.014) and positively correlated with leptin in males (r = 0.75, p = 0.002). An elevated daily HDE (β = 0.43, p = 0.038 and β = 0.47, p = 0.033) and trunk to total fat mass ratio (β = 0.46, p = 0.025, and β = 0.45, p = 0.037) were independently correlated with impaired lipid profile markers. Although there is no altered lipid profile, male patients demonstrated an increased fat distribution. However, female patients presented with an impaired lipid profile marker but demonstrated close values of normal fat distribution. Interestingly, the dose of glucocorticoid therapy can have some role in the lipid mechanisms.     

Technological and sensorial properties of liquid nitrogen ice cream enriched with protein from brewing waste (trub)

Debittered trub (brewing waste) is an important source of protein source (70.26%). Trub and whey protein were used for 5% protein enrichment of ice cream frozen by liquid nitrogen. Three formulations were elaborated: ice cream standard (ICS), ice cream with whey protein (ICW) and ice cream with trub (ICT). Chemical composition, rheological properties, texture, overrun, melting rate, scanning electron microscopy and a sensorial test were performed. Results showed that ICT presented a higher viscosity, obtained on the upward curve up to 6.76 Pa s⁻¹, consistency index (22.96 (Pa s⁻¹)ⁿ), hysteresis area (140.40 mPa s⁻¹) and hardness (31113.33 g) but a lower melting rate (0.38 g min⁻¹), overrun (13.92%) and sensorial acceptability than the other formulations. The addition of trub debittered for protein enrichment improved ice cream properties and demonstrated that it could be used as a food ingredient.     

Biodegradation of poly(lactic acid)—cassava bagasse composites produced by injection molding

Neat poly (lactic acid) (PLA) and PLA/cassava bagasse (CB) composites were used to produce seedling tubes by extrusion and injection molding. The tubes were buried in simulated soil, and their biodegradation was investigated by weight loss, scanning electron microscopy (SEM), and Fourier transform infrared spectroscopy (FTIR). After 180 days, the composites' biodegradation was higher than neat PLA material, and the higher the CB content, the higher the biodegradation, which caused fissures and voids in the material. The biodegradation of PLA/CB composites increased the phosphorus content in the soil after 180 days. Composites of PLA with CB, an abundant agro-industrial residue in Brazil, are promising because they can reduce the environmental impact due to CB's proper destination, and the composites' costs and biodegradation are faster than pure PLA material. Both the faster biodegradation of the tube and the higher P content are advantageous for seedling tubes.