Control of an industrial copper solvent extraction process

A two level control strategy that stabilizes and optimizes the production of an industrial copper solvent extraction process is presented. The stabilizing layer consists of a multi-input–multi-output controller or two single-input–single-output controllers with additional four feedforward compensators that regulate the flow rates in the copper solvent extraction process. The optimization layer consists of an optimizer that maximizes the production of the copper solvent extraction process and gives setpoints to the controllers at the stabilizing level. The mechanistic plant models, verified with industrial data, are linearized by identifying first and higher order transfer function models from simulated PRBS data. On the basis of the linear models, the interactions of the controlled variables, and the pairing of the controlled and manipulated variables are studied and the optimizer and the controllers designed. The control strategy employing two PI-control loops or a model predictive controller and additionally four feedforward control loops is successfully tested against simulated disturbances and setpoint changes. The control strategy is also compared to the data collected from the industrial plant under manual control. With this two level control strategy the production of the copper solvent extraction process is increased by 3–5% and the process variation is decreased by 70–90% compared to the manual operation of the case industrial plant. The results gained in simulation environment are successful and encouraging for further testing in an industrial plant.     

Compact varactor-tuned meander line monopole antenna for DVB-H signal reception

A compact varactor-tuned meander line monopole antenna for DVB-H signal reception is presented. The operating frequency of the antenna is continuously tuned over the frequency range of the DVB-H standard 470-702 MHz. The antenna has an omnidirectional radiation pattern and covers the frequency range with requisite impedance bandwidth and gain level. The antenna element occupies a very small volume (0.7 cm³ ) and can be used in 40 x 100 x 10 mm devices.     

Tunable microwave devices using low-sintering-temperature screen-printed barium strontium titanate (BST) thick films

A tunable microwave phase shifter composed of a low-sintering-temperature, screen-printable barium strontium titanate (BST) film and silver metallization was fabricated on an alumina substrate and co-fired at 900 °C for 3 h. The dielectric properties of the films were characterized in a frequency range of 0.8–8 GHz using scattering parameter measurements and a quasi-static coplanar waveguide transmission line model. The temperature dependency of the films was measured through capacitance measurements in a frequency range of 0.5–2.5 GHz. The figure of merit (phase shift/dB of insertion loss) of the phase shifter was found to be 14.6 at 3 GHz with an applied bias field strength of 2.5 V/μm. The performance of the phase shifter is briefly discussed and compared with other phase shifters fabricated by direct screen-printing of BST films.     

Performance evaluation of superorthogonal turbo codes in AWGN andflat Rayleigh fading channels

Turbo codes are parallel concatenated codes whose performance in the additive white Gaussian noise (AWGN) channel has been shown to be near the theoretical limit. In this paper, we describe a low-rate superorthogonal turbo code that combines the principles of low-rate convolutional coding and that of parallel concatenation. Due to the bandwidth expansion, this code outperforms the ordinary turbo code both in AWGN and especially in fading channels. Thus, superorthogonal turbo codes are suited mainly for spread-spectrum applications. For the purposes of iterative decoding, we concisely describe the connection between the optimal maximum a posteriori symbol estimation and suboptimal soft-output decoding based on sequence estimation. The suboptimal decoder produces outputs that can directly be used as additive metrics at successive decoding iterations, without the need for estimating channel noise variance. Simulation results in AWGN and flat Rayleigh fading channels are also presented, along with analytical upper bounds of bit- and frame-error probabilities     

The disruption of myofibre structures in rat skeletal muscle after forced lengthening contractions

Specific antibodies against structural proteins (actin, desmin, dystrophin, fibronectin) of muscle fibres were used to study the effect of forced lengthening contractions on muscle microarchitecture. Tibialis anterior (TA) muscle of male Wistar rats were subjected to 240 forced lengthening contractions. At consecutive time points (0, and 6 h, 2, 4, and 7 days) after stimulation, the TA muscle was excised for biochemical and histological assays. Beta-Glucuronidase activity, a quantitative indicator of muscle damage, showed increased values 2-7 days after the lengthening, peaking on day 4 (11.7-fold increase). A typical course of histopathological changes (myofibre swelling, necrosis and regeneration) was observed. In immunohistochemistry, the earliest abnormality observed was discontinuous dystrophin staining in some swollen fibres immediately after commencement of exercise, while at the same time no alterations occurred in the staining of the other antibodies studied. Six hours later, all the swollen fibres were uniformly desmin as well as dystrophin negative. The great majority, but not all, of the swollen fibres showed disorganized actin staining and intramyocellular localization of fibronectin. The early phase disruption of myofibre structures as measured in this study provides evidence of their central role following damage in skeletal muscle. These results suggest that the sequence of structural changes in the route to muscle fibre necrosis in injury induced by forced lengthening contraction originates in the disruption of the plasma membrane and the intermediate filament, which leads to disturbances in the myofibrillar system.     

Effects of 50 Hz magnetic fields on UV-induced skin tumourigenesis in ODC-transgenic and non-transgenic mice

The eukaryotic 20 S proteasome is a barrel-shaped protease complex, made up of four seven-membered rings. The outer and inner rings contain seven different alpha and beta-type subunits, respectively, each subunit located at a defined position. Recently, we have reported that the recombinant human alpha-type subunit C8 (HsC8) assembles into a heptameric ring-like structure by itself. In the present study we show that the two naturally neighboring alpha-type subunits of HsC8, HsPROS30 and HsPROS27, do not form ring-like complexes by themselves, but only dimers. This indicates that the propensity to form homo-oligomeric rings is not a general feature among human alpha-type subunits. However, coexpression of HsC8 and either of these neighbor alpha-type subunits results in the formation of hetero-oligomeric ring complexes, resembling the HsC8 ring-like structure. The ratio between the two types of subunits in the mixed complexes is surprisingly heterogeneous, varying from very high to very low HsC8 content. The three tested alpha-type subunits thus apparently lack binding sites that selectively interact with a specific neighboring subunit. This suggests that the correct positioning of the different alpha-type subunits in the eukaryotic 20 S proteasome is not dictated by the alpha-type subunits themselves, but rather by the interaction with specific beta-type subunits.     

Low-Loss and Wideband Package Transitions for Microwave and Millimeter-Wave MCMs

This paper presents high-performance flip-chip, through-substrate via and board-level BGA transition designs applicable in microwave and millimeter-wave multichip module (MCM) assemblies. Full-wave electromagnetic analysis was performed to achieve optimized transition structures. Interconnection test structures were fabricated in ceramic substrates and their performance was validated using on-wafer scattering parameter measurements. Both the flip-chip transition and the through-substrate via transition with a height of 800 mum exhibited return losses better than 25 dB and 20 dB, respectively, with low transmission losses up to 50 GHz. Furthermore, the wideband board-level BGA transition with a standoff height of 500 showed low insertion loss (< 0.5 dB) over a wide frequency range, from direct current (dc) up to 32.5 GHz.