Formation and Characterization of Ce3ZrO8 Prepared by the Hydrazine Method

A compound denoted as (Ce_0.75Zr_0.25)O₂ (Ce, ZrO₈) is formed near room temperature from cerium and zirconium nitrates using hydrazine monohydrate. It has a cubic unit cell with a = 0.5342 nm. Characterization of powders heated to various temperatures at 10°C/min demonstrates that the specific surface area does not decrease below 20 mVg until >1000°C.     

Plastic deformation in a multifunctional Ti-Nb-Ta-Zr-O alloy

Mechanisms for plastic deformation in the newly developed Ti-24 at. pct (Ta + Nb + V)-(Zr,Hf)-O alloys (Gum Metal) were investigated in relation to their unique properties. Transmission electron microscopy revealed that the microstructure after deformation was characterized by highly distorted crystal images, which are accompanied by numerous “giant faults.” Such plastic behavior implies that a large amount of elastic stain energy was stored discretely and hierarchically during cold working. Calculated elastic constants of the Ti-X (Nb,Ta,Mo,V) binary systems predicted that Young’s modulus in 〈001〉 and shear moduli along some directions including slip systems in a bcc crystal were extraordinary small. The low modulus not only well explains the highly distorted microstructure observed in the cold-worked specimens, but also signifies that ideal shear strength of the developed alloys is a very small value, which is close to the practical strength required for plastic deformation in the alloy. This implies that the giant faults observed in the deformed specimen were formed without the aid of dislocation glide.     

Rutile-type TiO2 thin film for high-k gate insulator

We investigated rutile-type titanium dioxide (TiO₂) films for possible use as a high-k gate insulator. The TiO₂ thin films were directly deposited on Si substrates using a RF magnetron sputtering method with a sintered oxide target. A single phase of rutile-type TiO₂ whose dielectric constant of approximately 75 was obtained when the film was deposited in an inert gas atmosphere and annealed at 800 °C in an oxidizing gas atmosphere. The oxygen ions were deficient in the as-deposited film, and consequently, a sufficient oxygen supply was needed to crystallize the film to a single phase of rutile during the post-annealing. However, the interfacial SiO₂ layer between the TiO₂ and the Si substrate simultaneously grew thicker than 2 nm. As the interfacial SiO₂ grew, the leakage current was decreased and the equivalent oxide thickness was increased, in the Au/rutile-type TiO₂/Si capacitor. Therefore, we concluded that the growth of the interfacial SiO₂ layer thicker than 2 nm is inevitable to form the single phase of rutile-type TiO₂ and to decrease the leakage.     

Infrared sensing properties of positive temperature coefficient thermistors with large temperature coefficients of resistivity

Infrared (IR) detecting elements were prepared using positive temperature coefficient (PTC) thermistors with large temperature coefficients of resistivity (α). Their compositions were denoted as Ba_1−x Sr _x Nb_0.003Ti_0.997O₃ + 1 mol % TiO₂ + 0.07 mol %MnO (x=0, 0.2), and their temperature coefficients of resistivity were 78 and 50% K⁻¹, respectively. Their IR sensing properties were measured under the self-regulating heating conditions, and were compared with those of a detector with small α (18 % K⁻¹). It was shown that large α was effective for controlling the element temperature by self-regulating heating and for improving sensitivity. The responsivity,R _v of the element withx=0.2 was 980 VW⁻¹, and was as large as those of pyroelectric detectors. Expressions which normalize the sensitivity and the thermal time constant were derived. From these expressions, criteria for improving some IR sensing properties were obtained.     

Gelation mechanism of agarose and κ-carrageenan solutions estimated in terms of concentration fluctuation

The gelation mechanism of agarose and κ-carrageenan aqueous solutions was investigated by using polarized light scattering and X-ray diffraction techniques in terms of the liquid-liquid phase separation. When an incident beam of He-Ne gas laser was directed to the gel prepared by quenching the agarose solution, the logarithm of scattered intensity increased linearly in the initial stage and tended to deviate from this linear relationship in the latter stage. If the linear increase in the initial stage could be analyzed within the framework of the linear theory of spinodal decomposition proposed by Cahn, the phase diagram indicated that the gelation is attributed to the phase separation due to the concentration fluctuation of solution. Furthermore, in the later stage showing the deviation of the linear relationship, light scattering under Hv polarization condition showed a X-type pattern indicating the existence of optically anisotropic rods, the optical axes being parallel or perpendicular with respect to the rod axis. In spite of the existence of the rods, no crystallites were confirmed by the corresponding X-ray diffraction and DSC measurements. For κ-carrageenan solutions, the logarithm of scattered intensity against time showed a constant value. This indicated that the gelation of κ-carrageenan solutions is independent of liquid-liquid phase separation but is due to the rapid formation of cross-linking points. Accordingly it turns out that the small difference of chemical structure between agarose and κ-carrageenan causes quite different gelation mechanism.     

Clinical implications of chromosomal abnormalities in 401 patients with myelodysplastic syndromes: a multicentric study in Japan

It is well known that cytogenetic analysis in patients with myelodysplastic syndrome (MDS) provides information useful in determining their prognosis. Based on the chromosomal results obtained from 401 MDS patients by a multicentric study in Japan, we studied correlations between chromosomal findings and prognosis or leukemic transformation in MDS patients. Patients with complex aberrations (cytogenetic abnormalities at more than three chromosomes), of any subtype, had a poor prognosis; for example, > 60% of patients with refractory anemia (RA) showing complex aberrations died within one year, but only 11% of them developed leukemia. In patients with RA with ringed sideroblasts (RARS), > 70% of those with complex aberrations evolved into the leukemic phase and survived for less than one year, suggesting a biologic heterogeneity in RARS patients. By contrast, about 5% of patients with RA or RARS exhibiting chromosomal findings other than -7/7q-, +8, two aberrations, and complex aberrations, developed leukemia and had a favorable prognosis. Therefore, the presence of chromosome abnormalities alone in patients with RA or RARS is not a factor in predicting leukemic transformation or poor prognosis. In patients with refractory anemia with an excess of blasts (RAEB), the presence of chromosome aberrations at MDS diagnosis affected the occurrence of leukemic transformation (24% versus 43%), however, no particular difference was noted in patients with RAEB in transformation with regard to whether they had chromosome changes or not, and about 60% of them evolved into leukemia. The poor prognosis related to complex aberrations was consistently noted in all MDS subtypes or age-matched groups, indicating that this cytogenetic anomaly is an independent risk factor for a poor prognosis in MDS patients. The duration between MDS diagnosis and development of the leukemic phase and that between the latter and death were significantly shorter in patients with complex aberrations than those without this change. Although the clinical significance of certain chromosomal abnormalities differs among subtypes of MDS, a new scoring system for predicting prognosis by cytogenetic changes, in combination with hematologic parameters, was proposed.     

66/77-kV C-GIS using composite insulation in SF6 gas

A second-generation model of cubicletype gas-insulated switchgear (C-GIS) with composite insulation incorporating SF₆ gas has been developed. The design does not require a gas process in field assembly; it has high reliability and its installation is more rapid; and a further reduction in size is achieved. The design principles are described in detail.     

New application of laser beam to failure analysis of LSI with multi-metal layers

A new technique for failure analysis of LSI with multi metal layers is described. There is a fabrication technique to form a big and optional window on upper layers using Nd-YAG laser without destroying any electrical function, and to approach the failure point through this window. The failure analysis procedure based on logical flow is presented. Fabrication technique is located in part of this procedure which consists of four steps. Two difficult reasons for approaching the failure point without fabrication technique are described. This difficulty results from line composition and line width. The fabrication procedure using Nd-YAG laser is reported. This procedure is to cover the chip surface with photo resist, and form a big and optional size window on upper layer with laser beam, and finally expose the purposed layer. Three failure analysis examples using this technique are introduced: unformed contact falure mode, Si-noduled failure mode, and isolation destroying failure mode.     

Wind resistant design of a tall building with an ellipsoidal cross section

This paper summarizes the results of the wind design carried out for the Act Tower building in Japan. Wind tunnel tests were performed in order to estimate the building response for different wind directions. Undesirable building motion perceived by building occupants is also studied and antivibration systems have been installed to solve this problem.