Effects of Prior Annealing on the Spark Plasma Sintering of Nanostructured Y2O3 Powders

The effects produced by annealing Y₂O₃ nanopowders on their spark plasma sintering (SPS) behavior are systematically investigated in this work. It is found that the annealed powders display higher sinterability with respect to the as‐received ones. Indeed, the maximum densification level reached from pristine powders is about 97.5%, whereas density decreases when further increasing either the sintering temperature or the dwell time. In contrast, the density of SPS products obtained from pretreated powder monotonically increases with temperature and processing time, thus leading to fully dense materials in 30 min at 1050°C and 60 MPa. Correspondingly, it is found that the annealing treatment markedly inhibits grain coarsening during SPS. Thus, dense translucent samples with grain size below 100 nm can be attained from annealed powders. On the other hand, white‐opaque specimens with significantly coarser microstructures (up to 1‐μm‐sized grains) are obtained when pristine powders are directly processed under the same sintering conditions. Furthermore, it is observed that the annealing treatment of SPS samples in air allows for graphite contamination removal, whereas no improvement in term of light transmittance is produced.     

Manganese Distribution between FeO‐MnO‐SiO2–CaO–MgO‐Al2O3 Slags and Molten Iron

Pretreatment of high manganese hot metal is suggested to produce hot metal suitable for further processing to steel in conventional LD converter and rich manganese slags satisfy the requirements for the production of silicomanganese alloys. Manganese distribution between slag and iron represents the efficiency of manganese oxidation from hot metal. The present study has been done to investigate the effect of temperature, slag basicity and composition of oxidizer mixture on the distribution coefficient of manganese between slag and iron. Ferrous oxide activity was determined in molten synthetic slag mixtures of FeO‐MnO‐SiO₂–CaO–MgO‐Al₂O₃. The investigated slags had chemical compositions similar to either oxidizer mixture or slags expected to result from the treatment of high manganese hot metal. The technique used to measure the ferrous oxide activity in the investigated slag systems was the well established one of gas‐slag‐metal equilibration in which molten slags contained in armco iron crucibles are exposed to a flowing gas mixture with a known oxygen potential until equilibrium has been attained. After equilibration, the final chemical analysis of the slags gave compositions having a particular ferrous oxide activity corresponding to the oxygen potential of the gas mixture. The determined values of ferrous oxide activity were used to calculate the equilibrium distribution of manganese between slag and iron. Higher manganese distribution between slag and iron was found to be obtained by using oxidizer containing high active iron oxide under acidic slag and relatively low temperature of about 1350°C.     

Multi-User MIMO Mobile CDMA Uplink System Employing Turbo Coding and Joint Detection Through a Multipath Rayleigh Fading Channel

In this paper, a generalized multiple-input multiple-output (MIMO) antenna system that can be fitted to the uplink of a wireless communication system is considered for the general case of multi-user. At the transmitter, the information bits are Turbo coded, then interleaved and passed through a serial-to-parallel converter. The channel is assumed bad urban suffering from multipath Rayleigh fading resulting in inter-symbol and multiple access interferences (ISI and MAI). At the front-end of the receiver, a number of receiving antennas are used followed by a joint multi-user estimator based on the Minimum Mean Square Error Block Linear Equalizer (MMSE-BLE).Computer simulations demonstrate a significant performance improvement in both single user and multi-user cases.This paper depends in parts on that presented at the 11th European Wireless Conference, Cyprus, Nicosia, pp. 187–192, April 2005. Yasmine A. Fahmy was born in Guiza, Egypt, on June 4, 1976. She received the B.Sc., M.Sc. and Ph.D. degrees in Communication and Electronics engineering from Cairo University, Egypt on 1999, 2001 and 2005 respectively. She is presently an assistant professor at Cairo University, Egypt. Her current field of interest is wireless communication and channel estimation. Hebat-Allah M. Mourad received her B.Sc., M. Sc. and Ph.D. degrees in electrical communication engineering from Cairo University, Egypt, in 1983, 1987 and 1994 respectively. Since 1983, she has been with the Department of Electronics and Communications, Faculty of Engineering, Cairo University, and is currently associate professor there. Her research interests include optical fiber communications, mobile and satellite communications. Emad K. Al-Hussaini received his B.Sc degree in Electrical Communication Engineering from Ain-Shams University, Cairo, Egypt, in 1964 and his M.Sc and Ph.D. degrees from Cairo University, Giza, Egypt, in 1974 and 1977, respectively. From 1964 to 1970, he was with the General Egyptian Aeroorganization. Since 1970, he has been with the Department of Electronics and Communications, Faculty of Engineering, Cairo University, and is currently professor there. He was a research fellow at Imperial College, London, UK, and at the Moore School of Electrical Engineering, University of Pennsylvania, Philadelphia, PA, USA, in the academic years 1976/1977 and 1981/1982, respectively. In 1990, he received the Egyptian national encouragement award for outstanding engineering research. He has written several papers for technical international journals and conferences. His research interests include signal processing, fading channel communication, modulation, and cellular mobile radio systems. Dr Al-Hussaini is a senior member of IEEE. He is listed in Marquis Whos Who in the World and in the IBC (International Biographical Center, Cambridge) for outstanding people of the 20th century.     

Conical magnetic bearings with radial and thrust control

Conical magnetic bearings with radial and thrust (axial) control are discussed. First a model of the conical bearing is made in state variable form. Airgap flux, airgap displacement, and velocity are used as state variables. A control method based on recent developments in control theory is proposed. The method is called Q-parameterization theory and is used to design a stabilizing controller for the system which, without control, is unstable in nature. The controller parameters are chosen using console (a software tandem for interactive optimization-based design) so that all design requirements are satisfied. Digital simulation was used to verify the proposed control method. Transient responses, forced responses in all three directions (vertical, horizontal, and axial), and the interactions between them are obtained. The results obtained are satisfactory and suggest the robustness of the proposed technique     

Lipid peroxidation and lysosomal integrity in different inflammatory models in rats: the effects of indomethacin and naftazone

The authors tried to establish quantitative and qualitative acoustic parameters of a good voice, suitable for future voice professionals. In their work they used long-time average spectrum analysis (LTAS) and three-dimensional analysis of periodicity (3D-PAN). They consider the regression straight line of formant regions and the parameters offered by 3D-PAN--jitter first of all--as the main acoustic parameters for the evaluation of voice quality and draw attention to the fact that acoustic parameters represent only one part of the evaluation of voice quality.     

Gurum Seeds: A Potential Source of Edible Oil

Cucurbitaceae family seeds are mostly discarded as agro-industrial wastes. Gurum (Citrullus lanatus var. colocynthoide) is an underutilized wild cucurbit plant, closely related to desert watermelon, which is grown abundantly in some African countries. Gurum seeds can play a significant role in health and nutrition due to their high oil content. This review describes the nutritional composition of gurum seeds and their oil profile. Gurum seeds are a good source of oil (27–35.5%), fiber (26–31%), crude protein (15–18%), and carbohydrates (14–17%). Gurum seeds oil is extracted by supercritical CO₂ (SFE), screw press, and solvent extraction techniques. The gurum seeds oil is composed of unsaturated fatty acids with a high proportion of linoleic acid (C18:2) and oleic acid (C18:1). Gurum seeds oil contains various bioactive compounds, such as tocopherols, phytosterols, and polyphenols. It is reported that solvent extraction gives a higher yield than the screw press and SFE, but the SFE is preferred due to safety issues. More studies are required for producing better quality gurum seeds oil by using novel extraction techniques that can increase oil yield.     

Effect of some superplasticizers on the mechanical and physicochemical properties of blended cement pastes

Blended cement pastes made of Portland cement and fine sand (known in Egypt as El-Karnak cement) were made using a water–cement ratio of 0.25 by weight. Three pastes containing admixture (water-soluble condensates) were also prepared using a water–cement ratio of 0.25 and condensate (superplasticizer) content of 0.25% by the weight of cement; the superplasticizers used are Na-phenol sulfonate formaldehyde, Na-polystyrene sulfonate, and Na-ß-naphthol sulfonate formaldehyde condensates. All pastes were cured for various time intervals within the range of 0.02–90 days. Compressive strength tests, hydration kinetics, X-ray diffraction analysis, thermal analysis, and surface properties were studied and related as much as possible to the pore structure of the hardened pastes. © 1995 John Wiley & Sons, Inc.