Finite-element grid improvement by minimization of stiffness matrix trace

A new and simple method of finite-element grid improvement is presented. The objective is to improve the accuracy of the analysis. The procedure is based on a minimization of the trace of the stiffness matrix. For a broad class of problems this minimization is seen to be equivalent to minimizing the potential energy. The method is illustrated with the classical tapered bar problem examined earlier by Prager and Masur. Identical results are obtained.     

Deposition of thin film silicon using the pulsed PECVD and HWCVD techniques

We report on the use of pulsed plasma-enhanced chemical vapor deposition (P-PECVD) technique and show that “state-of-the-art” amorphous silicon (a-Si:H) materials and solar cells can be produced at a deposition rate of up to 15 Å/s using a modulation frequency in the range 1–100 kHz. The approach has also been developed to deposit materials and devices onto large area, 30 cm×40 cm, substrates with thickness uniformity (<5%), and gas utilization rate (>25%). We have developed a new “hot wire” chemical vapor deposition (HWCVD) method and report that our new filament material, graphite, has so far shown no appreciable degradation even after deposition of 500 μm of amorphous silicon. We report that this technique can produce “state-of-the-art” a-Si:H and that a solar cell of p/i/n configuration exhibited an initial efficiency approaching 9%. The use of microcrystalline silicon (μc-Si) materials to produce low-cost stable solar cells is gaining considerable attention. We show that both of these techniques can produce thin film μc-Si, dependent on process conditions, with 1 1 1 and/or 2 2 0 orientations and with a grain size of approx. 500 A. Inclusion of these types of materials into a solar cell configuration will be discussed.     

Micromanipulation and cloning studies on buffalo oocytes and embryos using nucleus transfer

1. Nine male volunteers were exposed to the pyrethroid insecticide cyfluthrin. The study was performed in an exposure room, where an aerosol containing cyfluthrin was sprayed to obtain atmospheres with mean cyfluthrin concentrations of 160 and 40 micrograms/m3. Four volunteers were exposed for 10, 30 and 60 min at 160 micrograms/m3 and another five volunteers were exposed for 60 min at 40 micrograms/m3. For 160 micrograms/m3 exposure urine samples were collected before and immediately after exposure as well as for the periods 1-2, 2-3, 3-4, 4-5, 5-6, 6-12 and 12-24 h after exposure. For 40 micrograms/m3 exposure urine samples were collected before and 2 h after exposure. 2. The main urinary cyfluthrin metabolites, cis-/trans-3-(2,2-dichlorovinyl)-2,2-dimethylycyclopropane carboxylic acid (DCCA) and 4-fluoro-3-phenoxybenzoic acid (FPBA), were determined. The limit of detection (LOD) for all metabolites was 0.0025 microgram in an urine sample of 5 ml (0.5 microgram/l). After inhalative exposure of 40 micrograms cyfluthrin/m3 air for 60 min, the amount of metabolites in urine collected in the first 2 h after exposure was less than the LOD, namely 0.14 microgram for cis-DCCA, 0.15-0.28 microgram for trans-DCCA and 0.12-0.23 microgram for FPBA. 3. Of the metabolites, 93% was excreted within the first 24 h (peak excretion rates between 0.5 and 3 h) after inhalative exposure of 160 micrograms/m3. The mean half-lives were 6.9 h for cis-DCCA, 6.2 h for trans-DCCA and 5.3 h for FPBA. 4. The mean trans-:cis-DCCA ratio was 1.9 for the time course as well as for each subject. 5. The amount of metabolites in urine depends on the applied dose, on the exposure time and shows interindividual differences.     

印度水电方面的技术成就

大型水电工程需要大量的开挖隧洞，作者是负责印度国家水电公司（NHPC）所属的Tessta Ⅱ级水电工程的总工程师，现对印度在水电开发中的最新隧洞开挖工程做了一个展望。     

Component fatty acids of Cladosporium herbarum fat

Cladosporium herbarum grown as a surface culture in a chemically defined medium of sucrose and inorganic salts gave a high yield of fat (29.2%). The component acids of this fat have been found to be palmitic (34.2%); oleic (15.9%); linoleic (34.2%) and linolenic (15.7%). The combined proportion of linoleic and linolenic acids being about 50 per cent, the fat will be of great value for the manufacture of oil-modified resins as the films produced by such resins do not become yellow with age.     

Near infrared light-induced disassembly of polymeric micelles based on methylene blue conjugated polyethylene glycol

Light-sensitive drug delivery systems are considered ideal for applications in the biomedical fields for their ability to release the payload in an on-demand spatiotemporal controlled manner through the manipulation of the light source. Among the broad radiation spectrum, near infrared (NIR) light is considered advantageous compared to UV and visible light, due to its inherently lower photodamage to normal tissues and deeper penetration to lesion areas. In this study, we report a successful synthesis of a polymer capable of undergoing partial degradation upon irradiation with NIR light by conjugating 10-N-carbamoyl linkage methylene blue (MB) moiety, a NIR photocleavable ligand, with polyethylene glycol (PEG). Through effective coupling of MB, a hydrophobic moiety, to the hydrophilic PEG molecule, an amphiphilic polymer was synthesized, as demonstrated by a lowered surface tension (55 mN/m at 0.1% wt/vol). Subsequently, photo-induced reversal of surface activity associated with self-assembled structure disruption, was displayed by surface tension measurements, size distribution analysis, and burst release profile of paclitaxel (PTX) from polymeric micelles upon the exposure to NIR irradiation.     

Grounded discovery of symbols as concept–language pairs

In human designer usage, symbols have a rich semantics, grounded on experience, which permits flexible usage — e.g. design ideation is improved by meanings triggered by contrastive words. In computational usage however, symbols are syntactic tokens whose semantics is mostly left to the implementation, resulting in brittle failures in many knowledge-based systems. Here we ask if one may define symbols in computational design as {label,meaning} pairs, as opposed to merely the label. We consider three questions that must be answered to bootstrap a symbol learning process: (a) which concepts are most relevant in a given domain, (b) how to define the semantics of such symbols, and (c) how to learn labels for these so as to form a grounded symbol. We propose that relevant symbols may be discovered by learning patterns of functional viability. The stable patterns are information-conserving codes, also called chunks in cognitive science, which relate to the process of acquiring expertise in humans. Regions of a design space that contain functionally superior designs can be mapped to a lower-dimensional manifold; the inter-relations of the design variables discovered thus constitute the chunks. Using these as the initial semantics for symbols, we show how the system can acquire labels for them by communicating with human designers. We demonstrate the first steps in this process in our baby designer approach, by learning two early grounded symbols, tight and loose.