Electrochemical study of the chromium electrode behaviour in borate buffer solution

The electrochemical behaviour of the chromium electrode in borate buffer solution (pH 9.3) was studied by cyclic voltammetry and electrochemical impedance spectroscopy. Chromium passivity was observed over a broad potential region, from –1.0 to 0.5 V vs SCE. The passivation process took place in two steps: formation of a chromium oxide monolayer and transition of chromium to a higher valence state. The anodic film exhibited the properties of a p-type semiconductor. Transpassive dissolution of chromium occurred at 0.5 V vs SCE, with two reaction intermediates present, Cr_Cr ^III and Cr_ad ⁴⁺.     

Anodic stability of electrodeposited ruthenium: galvanostatic,thermogravimetric and X-ray photoelectron spectroscopy studies

The anodic stability of an electrodeposited ruthenium electrode was measured by anodic galvanostatic polarization in 0.5 mol dm^–3 H₂SO₄ solution. The role of water and adsorbed hydroxyl groups in electrode stability was determined by means of thermogravimetric analysis. A continuous weight loss due to water removal and condensation of hydroxyl groups was detected between 120 and 430 °C. The loss of a hydrous component of the oxide layer was in direct correlation with the increase of the anodic stability. Between 430 and 480 °C a weight gain was detected on the thermogravimetric curve. It was attributed to the formation of the ruthenium oxide layer in a higher oxidative state. This finding was confirmed by X-ray photoelectron spectroscopy measurements.     

Shear‐induced shish‐kebab structures in isotactic polypropylene using acicular precipitated calcium carbonate as whisker

It has been reported in the technical literature that whiskers of rodlike single crystals can be used in order to generate shish‐kebab structures or other different lamellae morphologies during isothermal or dynamic crystallization of sheared or presheared polymer melts. The expected advantage of the changed crystalline structure is a reinforcing effect of the composite. A lot of papers reported about the application of inorganic and organic whiskers such as cellulose and chitin whiskers. This study reports on an attempt to use acicular PCC as appropriate whisker for improving mechanical properties of polypropylene. In this article special attention is given to demonstrate the effect of flow induced crystallization under varying shear conditions in order to improve the mechanical properties. The effects were demonstrated using rheology, thermal analysis, tensile testing, and transmission electron microscopy. POLYM. ENG. SCI., 54:2057–2063, 2014. © 2013 Society of Plastics Engineers     

Influence of synthesis procedure on the morphology of bismuth oxide particles

A modified sol-gel procedure, based on the esterification reaction, was used to prepare the Bi₂O₃ precursor, which was then heated to 400 or 500 °C. β-Bi₂O₃ obtained at 400 °C showed well-shaped plate-like particles. The mixture β-Bi₂O₃/α-Bi₂O₃, obtained by prolonged heating at 400 °C, yielded pseudospherical particles having about 100 nm in size and much larger particles, as found by FE SEM. α-Bi₂O₃ obtained at 500 °C consisted of particles of varying shapes and sizes. Vitrification of α-Bi₂O₃ was also observed. XRD showed a small fraction of unidentified phase(s) in these samples. Different microstructures were obtained when the precipitation from aqueous Bi(NO₃)₃ solution with tetramethylammonium hydroxide at pH ∼ 14 was used. The precipitation at pH ∼ 3.5 yielded cloverleaf-like particles of good uniformity, which were assigned to BiOOH (isomorphous with (La_0.26Bi_0.24)Bi_0.5OOH. It was found that these particles were made up of much smaller primary BiOOH particles.     

Influence of solvent and temperature on extraction of phenolic compounds from grape seed,antioxidant activity and colour of extract

This study was aimed to investigate the influence of solvent (water and ethanol in concentration: 50%, 70% and 96%) and extraction temperature (25–80) °C on polyphenols extraction of grape seed (Vitis vinifera L. cv. “Frankovka”) cultivated in Eastern Croatia. The best results were reached using 50% ethanol at 80 °C. The most abundant individual polyphenolic compound was catechin which makes the average of 45.11% of the total phenolic content followed by epicatechin (34.45%), procyanidin B₂ (12.90%), gallic acid (5.34%), gallocatechin (1.58%), epicatechin gallate (1.01%). The antioxidant activity of extracts was determined by DPPH‐method and it was highly dependent on extraction solvent and temperature. The total extractable proanthocyanidins content of extract had the highest positive correlation (r = 0.994) with antioxidant activity, which indicated that these compounds might be the most important antioxidant in examined grape seed extracts. Relationship between phenolic content and colour of extracts was observed.     

Corrosion of aluminium in soft drinks

The corrosion of aluminium (A1) in several brands of soft drinks (cola- and citrate-based drinks) has been studied, using an electrochemical method, namely potentiodynamic polarization. The results show that the corrosion of A1 in soft drinks is a very slow, time-dependent and complex process, strongly influenced by the passivation, complexation and adsorption processes. The corrosion of A1 in these drinks occurs principally due to the presence of acids: citric acid in citrate-based drinks and orthophosphoric acid in cola-based drinks. The corrosion rate of A1 rose with an increase in the acidity of soft drinks, i.e. with increase of the content of total acids. The corrosion rates are much higher in the cola-based drinks than those in citrate-based drinks, due to the facts that: (1) orthophosphoric acid is more corrosive to A1 than is citric acid, (2) a quite different passive oxide layer (with different properties) is formed on A1, depending on whether the drink is cola or citrate based. The method of potentiodynamic polarization was shown as being very suitable for the study of corrosion of A1 in soft drinks, especially if it is combined with some non-electrochemical method, e.g. graphite furnace atomic absorption spectrometry (GFAAS).     

Removal of antimicrobials using advanced wastewater treatment

Removal of numerous classes of pharmaceuticals from the municipal and industrial wastewater, using conventional wastewater treatment, is incomplete and several studies suggested that improvement of this situation would require the application of advanced treatment techniques. This is particularly important for the treatment of industrial effluents, released from pharmaceutical industries, which can contain rather high concentrations of antimicrobials. The aim of this work was to evaluate membrane bioreactors (MBRs), nanofiltration, reverse osmosis and ozonation, as well as their combinations, for the removal of antimicrobials from a synthetic wastewater which simulated highly contaminated industrial effluents. The study was performed using a mixture of four important classes of antimicrobials, including sulfonamides (SA), fluoroquinolones (FQ), macrolides (MAC) and trimethoprim (TMP). Performance of two different types of MBRs, Kubota and Zenon, was evaluated under different regimes regarding hydraulic retention time, total organic load and total nitrogen load. It was shown that elimination of SA in MBR treatment was very efficient, while the elimination of MAC, FQ, and TMP was incomplete. A mass balance of these contaminants in MBR suggested that microbial transformation represented the main mechanism, while only a small percentage was eliminated from the aqueous phase by adsorption onto sludge particles. Nanofiltration and reverse osmosis achieved high elimination rates however produced highly contaminated concentrate. High removal was achieved using ozonation, but further research is needed to characterize formed ozonation products.     

Three‐dimensional time‐harmonic Green's functions for a triclinic full‐space using a symbolic computation system

Time‐harmonic Green's functions for a triclinic anisotropic full‐space are evaluated through the use of a symbolic computation system.This procedure allows evaluation of the Green's functions for the most general anisotropic materials. The proposed computational algorithms are programmed in a MATLAB environment by incorporating symbolic calculations performed using Maple Computer Algebra System. Extensive testing of the numerical results has been performed for both displacement and stress fields. The tests demonstrate the accuracy of the proposed algorithm in evaluating the Green's functions. Copyright © 2001 John Wiley & Sons, Ltd.     

Chaos-Based transmitted-reference ultra-wideband communications

Transmitted-reference (TR) ultra-wideband (UWB) communication systems have gained increasing popularity for the usage in the low data rate application, due to its non-coherent receiver structure. In conventional TR system, non-coherency at the receiver is achieved by sending reference pulses prior to the data-bearing pulses. Then, at the receiver side, reference pulses are used as template signals for correlation with data-bearing pulses. Therefore, the orthogonality between reference and data pulses is obtained in time division multiple access (TDMA) fashion. However, the implementation of a wideband delay line is very difficult in the current low power integrated circuits. In this paper, a TR method called Chaos-Based TR (CB-TR) is proposed. In the proposed method, chaotic sequences are used to separate the reference and data pulses. Such approach exploits the benefits of chaotic signals, such as non-periodicity, easy-to-generate, impulse-like autocorrelation value and low cross-correlation value. Furthermore, in order to decrease the influence of some negative properties of conventional chaotic maps, a modified chaotic generator (MCS) is proposed. Simulation results over the IEEE 802.15.4a channel model show comparable bit error rate performance to other TR methods.