Upflow anaerobic sludge blanket (UASB) treatment of supernatant of cow manure by thermal pre-treatment.

Upflow anaerobic sludge blanket (UASB) methane fermentation treatment of cow manure that was subjected to screw pressing, thermal treatment and subsequent solid-liquid separation was studied. Conducting batch scale tests at temperatures between 140 and 180 degrees C, the optimal temperature for sludge settling and the color suppression was found to be between 160-170 degrees C. UASB treatment was carried out with a supernatant obtained from the thermal treatment at the optimal conditions (170 degrees C for 30 minutes) and polymer-dosed solid-liquid separation. In the UASB treatment with a COD(Cr) loading of 11.7 kg/m3/d and water temperature of 32.2 degrees C, the COD(Cr) level dropped from 16,360 mg/L in raw water to 3,940 mg/L in treated water (COD(Cr), removal rate of 75.9%), and the methane production rate per COD(Cr) was 0.187 Nm3/kg. Using wastewater thermal-treated at the optimal conditions, also a methane fermentation treatment with a continuously stirred tank reactor (CSTR) was conducted (COD(Cr) in raw water: 38,000 mg/L, hydraulic retention time (HRT): 20 days, 35 degrees C). At the COD(Cr) loading of 1.9 kg/m3/d, the methane production rate per COD(Cr), was 0.153 Nm3/kg. This result shows that UASB treatment using thermal pre-treatment provides a COD(Cr), loading of four times or more and a methane production rate of 1.3 times higher than the CSTR treatment.     

An optically clocked transistor array with dual serial-to-parallel and parallel-to-serial conversion capability for optical label swapping

We propose an optically clocked transistor array optoelectronic integrated circuit (OEIC) for both serial-to-parallel and parallel-to-serial conversion (demux/mux), enabling an interface between high-speed asynchronous burst optical labels and CMOS circuitry for optical label swapping. Dual functionality of the OEIC reduces size, power, and cost of the optical label swapper. The capability for greater than 20-Gb/s conversion operation is demonstrated.     

10 Gbit/s optical soliton transmission over 7200 km by using amonolithically integrated MQW-DFB-LD/MQW-EA modulator light source

The authors demonstrate 10 Gbit/s optical soliton transmission in a recirculating loop through the use of a monolithically integrated MQW-DFB-LD/MQW-EA modulator light source. The timing jitter due to the Gordon-Haus effect is successfully reduced by the optical bandpass filters conventionally used in the cascaded EDFAs to avoid the accumulation of amplified spontaneous emission. The transmission distance of 7200 km is achieved at a bit error rate of 10^-9     

OTDM transmitter using WDM-TDM conversion with an electroabsorptionwavelength converter

An all-optical multiplexing technique using wavelength division multiplexing (WDM)-time division multiplexing (TDM) conversion with an electroabsorption wavelength converter has been proposed and demonstrated. The effectiveness of this WDM-TDM conversion technique for various pulsewidth settings was experimentally investigated. The fluctuation of the signal performance, which was inevitably caused by the coherent crosstalk between adjacent pulses in the conventional optical time division multiplexing (OTDM) technique, were successfully suppressed, even in the case of wide pulse duration. High Q-factor performance has been maintained for a wide range of duty ration from 36% to 74%. By introducing this technique to the optical time division multiplexer, a highly stable and high-quality 40-Gb/s optical signal can be effectively produced without generating the short pulse or setting two tributaries at orthogonal polarization states, and without introducing high-speed electronics for signal multiplexing. The WDM-TDM conversion with an electroabsorption wavelength converter was extended to 60-Gb/s operation by using three 20-Gb/s tributaries. A clear eye opening was confirmed for a waveform after the WDM-TDM conversion of the 60-Gb/s signal     

Chemical leaching and magnetic properties of non-equilibrium Al(Co–Cu) powders produced by rod milling

We report upon the chemical leaching and magnetic properties of nanoscale crystalline Al_0.6(Co₂₅Cu₇₅)_0.4 alloy powders produced by rod milling. X-Ray diffractometry (XRD), transmission electron microscopy, differential scanning calorimetry, vibrating sample magnetometry, and superconducting quantum interference device magnetometry were used to characterize the as-milled and leached specimens. After 400 h of milling, only the b.c.c. phase of the intermetallic compound γ-Al_3.892Cu_6.10808 was detected by XRD. After annealing the leached specimen at 600 °C for 1 h, the nanoscale crystalline phase was transformed into the f.c.c. Cu phase, and this was accompanied by a change in the magnetic properties. The peaks of the magnetization shifted towards lower temperature with increasing external field. The temperature behavior at T_f (45 K) for direct current (d.c.) magnetic susceptibility measurements was quite different for field cooling and zero-field cooling. After cooling the leached specimen from 800 °C, magnetization increased gradually.     

Evaluation of inelastic constitutive models under plasticity-creep interaction for steel at 600°C

Uniaxial tests to identify plasticity-creep interaction in steel at 600°C were carried out as the Benchmark Project by the Subcommittee on Inelastic Analysis and Life Prediction, JSMS. The purpose of this paper is to present recent experimental data and predictions of constitutive models obtained in the project. Ten types of constitutive models were utilized to compare analytical predictions to sixteen benchmark experiments which are grouped into four categories: (I) tensile and creep tests under monotonic loading, (II) mixed mode tests under plastic and creep loading, (III) ratcheting deformation tests under program loads, and (IV) cyclic deformation tests under the combination of different strain rates. The benchmark tests in Group IV are used to estimate the creep-fatigue life of steel; the results will be published in a separate paper.     

Verification of a model for estimating the void fraction in a three-component randomly packed bed

The void fraction in a three-component randomly packed bed was calculated from the authors' model, and the calculated values were compared with published experimental data for spherical and irregularly shaped particles and with results from computer simulations. Results from the model were in good agreement with simulated and published experimental data.     

An Adaptive Recipe Implementation in Case‐Based Formalism for Abnormal Condition Management

This paper deals with accurate recipe implementation for abnormal condition management in a batch process using a case‐based reasoning (CBR) approach. A set of new problems can be solved by reusing proven process solutions. The proposed system integrates quantitative and qualitative parameters for adaptation of cases. A novel methodology to generate accurate recipes and to adapt to the processes is introduced during normal and abnormal conditions. In particular, the differences between current conditions and the references (recipes) should be managed to prevent any hazardous conditions arising. The processes are evaluated using their similarity to the past cases. This intelligent approach distinguishes plausible cases, generates accurate recipes, and adapts to new situations. The aim is to use the offline historical process data and safety related information in order to propose changes and adjustments in the processes.     

Microbial sensor for preliminary screening of mutagens utilizing a phage induction test

For the preliminary screening of mutagens, a novel microbial sensor system was developed utilizing a phage induction test. Escherichia coli lysogenic strain GY5027 and nonlysogenic strain GY5026 were used in this study. The number of living cells was determined by measuring the respiration of cells immobilized onto an oxygen electrode. The injection of a mutagen, such as AF-2 and MNNG, caused the phage induction in the lysogenic strain, resulting in the decreased respiration of only the lysogenic strain immobilized onto the oxygen electrode but not of nonlysogenic strain. The rate of current increase correlated well with the concentration of mutagens. The sensor responses to the antibiotics and bactericides were definitely different from those of mutagens. Therefore, utilization of this microbial sensor system makes possible the estimation of a substrate's mutagenicity.