V2O5 nanofibre sheet actuators

Vanadium oxides, such as V2O5, are promising for lithium-ion batteries, catalysis, electrochromic devices and sensors. Vanadium oxides were proposed more than a decade ago for another redox-dependent application: the direct conversion of electrical energy to mechanical energy in actuators (artificial muscles). Although related conducting polymer and carbon nanotube actuators have been demonstrated, electromechanical actuators based on vanadium oxides have not be realized. V2O5 nanofibres and nanotubes provide the potential advantages of low-cost synthesis by sol-gel routes and high charging capacity and long cycle life. Here, we demonstrate electromechanical actuation for obtained high modulus V2O5 sheets comprising entangled V2O5 nanofibres. The high surface area of these V2O5 sheets facilitates electrochemical charge injection and intercalation that causes the electromechanical actuation. We show that the V2O5 sheets provide high Young's modulus, high actuator-generated stress, and high actuator stroke at low applied voltage.     

Degradation of reactive dyes in wastewater from the textile industry by ozone: Analysis of the products by accurate masses

The present work describes the use of ozone to degrade selected reactive dyes from the textile industry and the analysis of the resulting complex mixture by liquid chromatography/mass spectrometry (LC-MS). To allow certain identification of the substances detected in the wastewater, the original dyes were also investigated either separately or in a synthetic mixture of three dyes (trichromie). Since the reactive dyes are hydrolyzed during the dyeing process, procedures for the hydrolysis were worked out first for the individual dyes. The ozonated solutions were concentrated by solid-phase extraction, which separated very polar or ionic substances from moderately polar degradation products. The latter, which are the primary degradation products, were investigated by liquid chromatography/mass spectrometry with a tandem quadrupole time-of-flight mass analyzer. Accurate masses, which in most cases could be determined with a deviation of ≤5 ppm from the exact value, were also measured. In addition, a diode-array detector was placed before the mass analyzer to provide UV-vis spectra of the products in the same run. With retention times, mass spectra, accurate masses, UV-vis spectra and, of course, knowledge of the structures of the original dyes, plausible structures could be proposed for most of the components of the moderately polar fraction. These structures were confirmed by ¹H NMR in cases where it was practical to isolate the degradation products by preparative HPLC.     

Discrete element analysis of experiments on mixing and stoking of monodisperse spheres on a grate

Understanding the details of the mixing and stoking process on grate firing systems is crucial for the optimization of the combustion process in waste or biomass incineration plants. The Discrete Element Method (DEM) can help to obtain further information on the mixing process within a bed of fuel particles. Especially the influence of a change in operational parameters can be examined avoiding large experimental effort. In the current paper five simulations for a generic grate are compared with the corresponding experiments. The experiments were carried out throughout an anterior parameter study on mixing and stoking on a grate [Sudbrock F.; Simsek E.; Wirtz S.; Scherer V.: “An experimental analysis of the influence of operational parameters on mixing and stoking of a monodisperse granulate on a grate”, Powder Technology 198, Issue 1, 29-37, 2010] [19]. The system considered is equipped with vertically moving bars which induce stoking. In a first approach monodisperse plastic spheres are used. The grate is encased by a transparent polycarbonate housing which provides optical access to the movement of the particles in the wall planes. The mixing process is measured and quantified by image analysis of the front wall of the grate. The mixing behaviour of the particle assembly observed in experiments and simulation appears to be very similar indicating that DEM is able to predict the particle mixing in the bed. In order to quantify the visual observations the mixing behaviour has been evaluated by different mixing parameters. They are compared in dependence of the number of strokes of the grate bars. A good agreement between measurements and simulations could be observed.     

Effect of size and shape of metal particles to improve hardness and electrical properties of carbon nanotube reinforced copper and copper alloy composites

Utilizing the extra-ordinary properties of carbon nanotube (CNT) in metal matrix composite (MMC) for macroscopic applications is still a big challenge for science and technology. Very few successful attempts have been made for commercial applications due to the difficulties incorporating CNTs in metals with up-scalable processes. CNT reinforced copper and copper alloy (bronze) composites have been fabricated by well-established hot-press sintering method of powder metallurgy. The parameters of CNT–metal powder mixing and hot-press sintering have been optimized and the matrix materials of the mixed powders and composites have been evaluated. However, the effect of shape and size of metal particles as well as selection of carbon nanotubes has significant influence on the mechanical and electrical properties of the composites. The hardness of copper matrix composite has improved up to 47% compared to that of pure copper, while the electrical conductivity of bronze composite has improved up to 20% compared to that of the pure alloy. Thus carbon nanotube can improve the mechanical properties of highly-conductive low-strength copper metals, whereas in low-conductivity high-strength copper alloys the electrical conductivity can be improved.     

Influence of Human Jaw Periosteal Cells Seeded β-Tricalcium Phosphate Scaffolds on Blood Coagulation

Tissue engineering offers auspicious opportunities in oral and maxillofacial surgery to heal bone defects. For this purpose, the combination of cells with stability-providing scaffolds is required. Jaw periosteal cells (JPCs) are well suited for regenerative therapies, as they are easily accessible and show strong osteogenic potential. In this study, we analyzed the influence of uncoated and polylactic-co-glycolic acid (PLGA)-coated β-tricalcium phosphate (β-TCP) scaffolds on JPC colonization and subsequent osteogenic differentiation. Furthermore, interaction with the human blood was investigated. This study demonstrated that PLGA-coated and uncoated β-TCP scaffolds can be colonized with JPCs and further differentiated into osteogenic cells. On day 15, after cell seeding, JPCs with and without osteogenic differentiation were incubated with fresh human whole blood under dynamic conditions. The activation of coagulation, complement system, inflammation, and blood cells were analyzed using ELISA and scanning electron microscopy (SEM). JPC-seeded scaffolds showed a dense cell layer and osteogenic differentiation capacity on both PLGA-coated and uncoated β-TCP scaffolds. SEM analyses showed no relevant blood cell attachment and ELISA results revealed no significant increase in most of the analyzed cell activation markers (β-thromboglobulin, Sc5B-9, polymorphonuclear (PMN)-elastase). However, a notable increase in thrombin-antithrombin III (TAT) complex levels, as well as fibrin fiber accumulation on JPC-seeded β-TCP scaffolds, was detected compared to the scaffolds without JPCs. Thus, this study demonstrated that besides the scaffold material the cells colonizing the scaffolds can also influence hemostasis, which can influence the regeneration of bone tissue.     

Novel Columnar Tetraphenylethenes via McMurry Coupling

Several tetraphenylethenes 2a , 4a – i with lipophilic side chains were synthesized and their mesomorphic properties were investigated. The most promising candidates turned out to be tetrakis[4‐(trisalkyloxybenzoyloxy)phenyl]ethenes 4e – i with chain lengths between C₇ and C₁₂. Compounds 4 were prepared by a convergent strategy employing a McMurry coupling of 4,4′‐dimethoxybenzophenone 1c , followed by demethylation and subsequent esterification of 2c with either 4‐decyloxybenzoic acid 3a , 3,4‐didecyloxybenzoic acid 3b , or O‐alkylated gallic acids 3c – i . Despite the twisting of the central tetraphenylethene moiety compounds 4c – i display hexagonal columnar mesophases according to differential scanning calorimetry (DSC), polarizing microscopy, and X‐ray diffraction studies.