Electrical Breakdown Properties and Space Charge Formation in High Temperature Region in Ultraviolet Ray Irradiated PVC

Polyvinyl chloride (PVC) is the most popular insulating material for electric wiring instruments. However, an exothermic reaction above 150 °C may cause deterioration of the insulating properties of PVC. Therefore, it is important to clarify the heat degradation in PVC, not only to investigate the ignition of electrical wiring products but also to use electrical products safely. It is known that ultraviolet (UV) irradiation causes chemical deterioration of PVC and an increase in its conductivity. Generally, it has been thought that the electrical breakdown properties, electrical conduction, and insulating performance are affected by space charge accumulation in an insulating material. A high temperature pulsed electroacoustic (PEA) system usable up to 250 °C has been developed, and the PEA system can measure the space charge distribution and conduction current in the high temperature range simultaneously. In this investigation, the space charge distribution and conduction current were measured up to electrical breakdown in a non‐UV irradiated sample (normal PVC) and in 353 nm and 253 nm UV‐irradiated PVC samples in the range from room temperature to 200 °C in a DC electric field. In the short wavelength UV irradiated PVC sample (253 nm, 300 h), a deterioration of breakdown strength at 90 °C to 150 °C and negative packet‐like charges were observed at 60 °C and 100 °C, a positive charge accumulated in front of both the anode and cathode above 90 °C, and a higher electric field near the cathode side because the positive charge of the cathode side was greater.     

Evaluation of the wettability of spherical cement particle surfaces using penetration rate method

The wettability of cement particles is related to the fluidity of cement paste. This paper describes the mechanism of the higher fluidity imparted by the spherical cement particles in light of their wettability. In addition, the effects of gypsum on the wettability were also studied. This study has shown the following: (1) The weight of water and water-reducing agent solution penetrating the spherical cement powder bed is 24-150% higher than that for the ordinary Portland cement powder bed. This results in the improvement of the wettability of the particle surfaces of spherical cement. The high wettability of spherical cement contributes to its high fluidity. (2) The presence of many fine gypsum particles on the spherical cement particle surface reduces the wettability. (3) To prepare spherical cement, the optimum amount of gypsum added is determined by the acceleration of the formation of spherical particles and the wettability of particle surfaces.     

Growth of β-Alumina (Na2O · 11Al2O3) Single Crystals by the Flux Method

The crystal-growth process and growth conditions of β-alumina (Na₂O · Al₂O₃) were investigated using the Na₂B₄O₇-Na₃AlF₆ flux method. β-Alumina (electric fusion brick) was used as both nutrient and seed. Weight loss of the flux varied widely for various runs: ≅ 10 wt% of flux evaporated at 100 h, ≅ 17 wt% at 150 h, and 43 wt% at 600 h. When β-alumina crystal was grown, only 20 wt% Na₂B₄O₇ was added to the Na₃AlF₆ flux. The linear growth rates of the β-alumina single crystal grown by an Na₃AlF₆-20 wt% Na₂B₄O₇ flux method at 1040°C and Δ t = 18°C were ≅ 1.0 × 10⁻³ mm/h ( a face) and ≅0.3 × 10⁻³ mm/h ( c face). The β-alumina single crystals grown were bounded by only c [001] and a [100] and were colorless and transparent.     

Single-crystal growth and characterization of Cu2O and CuO

We have prepared a large number of crystals of cuprous oxide (Cu2O) by various procedures. Photoluminescence spectra of these crystals were studied to examine the concentration of defects, especially copper vacancy VCu to seek favourable conditions for growing Cu2O crystal. High-quality single crystals of Cu2O were prepared by the floating-zone melting method in air. Several synthetic crystals (specimens FA, FZ and GZ) and also a natural crystal were studied by X-ray analysis, inductively coupled plasma spectroscopy analysis, optical absorption, photoluminescence, photoconductivity and cyclotron resonance absorption, photoluminescence, photoconductivity and cyclotron resonance absorption to characterize their optical and electrical qualities. The best values of mobility and scattering time of photocarriers at T = 4.2 K are estimated to be h1.8 × 105 cm2 V–1 s–1 and h60 ps for positive holes, and 1.3 × 105 cm2 V–1 s–1 and 70 ps for electrons in Cu2O. Further, we report preliminary experimental results on transport property of crystals also of cupric oxide (CuO) purified by the floating-zone melting method.     

New pixel driving circuit using self‐discharging compensation method for high‐resolution OLED micro displays on a silicon backplane

A new 4T2C pixel circuit formed on a silicon substrate is proposed to realize a high‐resolution 7.8‐μm pixel pitch AMOLED microdisplay. In order to achieve high luminance uniformity, the pixel circuit compensates its Vth variation of the MOSFET for the driving transistor internally by using self‐discharging method. Also presented are 0.5‐in Quad‐VGA and 1.25‐in wide Quad‐XGA microdisplays with the proposed pixel circuit.     

A knowledge assimilation method for logic databases

In this paper we consider a deductive question-answering system for relational databases as a logic database system, and propose a knowledge assimilation method suitable for such a system. The concept of knowledge assimilation for deductive logic is constructed in an implementable form based on the notion of amalgamating object language and metalanguage. This concept calls for checks to be conducted on four subconcepts, provability, contradiction, redundancy, independency, and their corresponding internal database updates. We have implemented this logic database knowledge assimilation program in PROLOG, a logic programming language, and have found PROLOG suitable for knowledge assimilation implementation.