Characteristics of Milk Powders Produced by Spray Freeze Drying

Skim and whole milk powders were manufactured at lab scale by spray freeze drying (SFD), using liquid nitrogen as the cryogen. The polydispersity of droplet/particle sizes was limited using an encapsulator nozzle to atomize the feed. Particle morphology was examined using a scanning electron microscope. Samples were compared with equivalent spray-dried powders in tests of wettability and dissolution in water. The spray freeze-dried powders were found to be highly porous, with a uniform structure of pores throughout the entire particles. When tested in water, SFD skim milk powders wetted roughly three times as fast as industrially spray-dried agglomerated skim milk powders and were observed to dissolve rapidly by breaking down into smaller particles.     

Residual stresses and transformation toughening in MoSi2 composites reinforced with partially stabilized zirconia

The results of study of the effects of yttria stabilization (0–6 mol.%) on the room-temperature fracture behavior and toughening mechanisms in zirconia-reinforced MoSi₂ are presented in this paper. Transformation toughening is shown to occur only in composites reinforced with zirconia particles stabilized with 2 mol.% yttria. However, the fracture toughness levels are comparable in the other composites with yttria levels between 0 and 6 mol.%. Toughening in the other composites is attributed to the combined effects of residual stress, microcrack shielding/anti-shielding and/or crack deflection. A rigorous micromechanics-based model is presented for the estimation of residual stress levels in brittle materials reinforced with phases that can transform during cooling or under stress. The model is applied successfully to the rationalization of the observed fracture and toughening phenomena.     

Developing competency-based methods for near-real-time air combat problem solving assessment

Air combat scenarios present unique problems where the solution is not obvious. An advanced networked simulation environment can be used to train high-level cognitive air combat skills such as problem solving. A problem in the development of principled and construct oriented assessment is related to determining the level of specificity of the assessment. We present a detailed discussion of the definition of critical competencies associated with combat mission problem solving performance, and we describe our approach to develop and implement an embedded performance assessment system that maps outcomes to these competencies. Finally, we discuss the implications for our approach for comprehensive assessment and discuss our goals for an evaluation of the competency-based approach to assessment.     

Reliability assessment of polysilicon MEMS structures under mechanical fatigue loading

This paper examines the current status and methodologies of study of material and system reliability in Microelectromechanical Systems (MEMS). This includes: a review of the current literature in the area of MEMS regarding failure analysis experimental investigations; testing methods and philosophies for material characterization and possible mechanistic analytical solutions for estimating material properties. The paper proposes a reliability framework that encompasses all the available information. This statistical platform will enable the MEMS design engineer to distill all the available information in the literature into a stand-alone semi-empirical material reliability model, and a holistic system-level model for a complete system.     

Ductile-phase toughening and Fatigue-Crack Growth in Nb-Reinforced Molybdenum Disilicide Intermetallic Composites

A study has been made of the role of ductile-phase toughening on the ambient temperature fracture toughness and fatigue-crack propagation behavior of a molybdenum disilicide intermetallicmatrix composite reinforced with 20 vol pct niobium spheres. Using disk-shaped compact DC(T) samples, only moderate improvements (∼24 pct) in fracture toughnessK _lcvalues were found for the composite compared to the unreinforced MoSi₂ matrix material. Moreover, (cyclic) fatigue- crack propagation was seen at stress intensities as low as 75 to 90 pct ofK _Ic, with growth rates displaying a high dependency (∼14) on the applied stress-intensity range. The lack of significant toughening due to the incorporation of ductile Nb particles is associated with an absence of crack/particle interactions. This is attributed to the formation of a weak reaction-layer interface and elastic mismatch stresses at the crack tip between the Nb and MoSi₂, both factors which favor interfacial debonding; moreover, the spherical morphology of Nb phase stabilizes cracking around the particle. Results suggest that increasing the aspect ratio of the distributed Nb rein- forcement phase with attendant interfacial debonding and eliminating possible Nb-phase em- brittlement due to interstitial impurity contamination are critical factors for the successful development of tougher Nb/MoSi₂ structural composites. Formerly with McDonnell Formerly with McDonnell     

An investigation of crack closure and the propagation of semi-elliptical fatigue cracks in Q1N (HY80) pressure vessel steel

The results of an experimental investigation of the effect of crack closure on the propagation of semi-elliptical fatigue cracks are presented. Load-shedding fatigue threshold tests were carried out at stress ratios of 0.2, 0.35, 0.5 and 0.7. Crack closure was measured at the surface and depth positions using backface strain gauges, near-tip gauges, and a clip gauge. Differences between the surface and depth growth behaviour are explained by considerations of the effects of the transition from plane stress conditions at the surface to plane strain conditions at the depth. The effects of stress ratios are attributed largely to differences in the crack opening displacement, which result in asperities coming into contact to induce roughness-induced crack closure.     

"Learning myopia: An adaptive recency effect in category learning": Correction to Jones and Sieck (2003).

Reports an error in "Learning myopia: An adaptive recency effect in category learning" by Matt Jones and Winston R. Sieck (Journal of Experimental Psychology: Learning, Memory, and Cognition, 2003[Jul], Vol 29[4], 626-640). On page 633, Table 2, the values in columns (T, P) and (P, T) in the dual condition row incorrectly read .10 and .90, respectively. The correct values are .90 and .10, respectively. (The following abstract of the original article appeared in record 2003-06626-013.) Recency effects (REs) have been well established in memory and probability learning paradigms but have received little attention in category learning research. Extant categorization models predict REs to be unaffected by learning, whereas a functional interpretation of REs, suggested by results in other domains, predicts that people are able to learn sequential dependencies and incorporate this information into their responses. These contrasting predictions were tested in 2 experiments involving a classification task in which outcome sequences were autocorrelated. Experiment 1 showed that reliance on recent outcomes adapts to the structure of the task, in contrast to models' predictions. Experiment 2 provided constraints on how sequential information is learned and suggested possible extensions to current models to account for this learning. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Analysis of Indentation Crack as a Wedge-Loaded Half-Penny Crack

Surface cracks produced by indentation with a Vickers indenter were modeled as half-penny cracks extended by symmetric disk-shaped wedges. The wedge diameter was assumed to be equal to the hemispherical plastic zone size, and the wedge thickness was calculated by equating the wedge volume to the hardness-impression volume. The resulting equilibrium relation between the indentation load and the radius of the half-penny crack is in good quantitative agreement with similar relations obtained from fracture toughness calibration.     

A simplified method for analyzing mold filling dynamics. Part II: Extensions and comparisons with experiment

A dimensional analysis based on four parameters has been developed previously to predict injection pressure; clamp force, and bulk temperature for the injection molding of amorphous materials in center-gated disk-shaped cavities. In this paper geometric and semicrystalline-materials approximations are introduced and tested for extending the previous analysis to include multigated thin cavities and semicrystalline materials. The combination of these approximations and the previous analysis, known hereafter as the Radial Flow Method (RFM), greatly simplifies the analysis of mold filling. The geometric approximation, which is based on a simple model for the axial stress distribution in the cavity, is shown to give reasonable predictions when compared with experimental data and a numerical two-directional flow simulation for the filling of an off-center-gated rectangular cavity with acrylonitrilebutadiene-styrene copolymer (ABS). The semicrystallinematerials approximation, in which heat capacity and viscosity changes during crystallization are neglected, is shown to give good agreement with experimental data for the filling of a center-gated disk-shaped cavity with polypropylene. As an illustration, the Radial Flow Method is used to analyze the molding of a large, thin-wall automobile interior trim panel. The inlet melt temperature, mold-wall temperature, part thickness, injection rate, viscosity and gate locations are varied in a series of calculations to determine the relative effectiveness of these variables in lowering the injection pressure and Clamp force. The results obtained with the Radial Flow Method are in good agreement with those obtained by a finiteelement simulation of two-directional flow.     

Developmental variations in plasma leptin,leptin soluble receptor and their molar ratio in healthy infants

Background  

Leptin and its soluble receptor (sOB-R) are important to regulation of body composition but there are no data on the developmental variations in these plasma variables and their relationship with body composition measurements,