Lightning Observation in 3D Using a Multiple LF Sensor Network and Comparison with Radar Reflectivity

A three‐dimensional (3D) lightning mapper consisting of multiple low‐frequency (LF) sensors has been developed to monitor thunderstorms and to estimate their charge structure. We have been conducting an observation campaign using the 3D lightning mapper in Kansai, Japan, since October 2012. In this study, we determine 3D source locations of intracloud and cloud‐to‐ground flashes and compare them with the radar reflectivity estimated by phased‐array radar (PAR) with high temporal and spatial resolution. Most LF sources are located in high radar reflectivity regions, confirming that the 3D LF lightning mapper monitors thunderstorms. A lightning flash with heavy branches is clearly imaged. Based on the bidirectional leader theory that negative and positive ends of a lightning leader develop simultaneously, we estimate the positive and negative charge regions in a thundercloud from the LF source locations. The radar reflectivity estimated by PAR supports the charge structure estimated by LF source locations.     

A NUMERICAL SIMULATION OF SWIRLING FLOW PNEUMATIC CONVEYING IN A HORIZONTAL PIPELINE

ABSTRACT

A numerical simulation for swirling and axial flow pneumatic conveying in a horizontal pipe was carried out with a Eulerian approach for the gas phase and a stochastic Lagrangian approach for particle phase, where particle-particle and particle-wall collisions were taken into consideration. The k-? turbulence model is used to characterize the time and length scales of the gas-phase turbulence. Models are proposed for predicting the particle source and additional pressure loss. The numerical results are presented for polyethylene pellets of 3.1 mm diameter conveyed through a pipeline of 13 m in length with an inner diameter of 80 mm, solid mass flow rate was 0.084 kg/s, and gas velocity was varied from 10 m/s to 18 m/s. The particle flow patterns, the particle concentration and the particle velocity, and additional pressure loss were obtained. It is found that the particle velocity and concentration has almost same value along flow direction in swirling flow pneumatic conveying. The profile of particle concentration for swirling flow pneumatic conveying exhibits symmetric distribution towards the centerline and the higher particle concentration appears in neighbor of wall in the acceleration region. At downstream, the uniform profile of particle concentration is observed. The particle velocity profile, on the other hand, is uniform for both swirling and axial flow pneumatic conveying. A comparison of the calculations with the measured data shows a good agreement within an average error of less than 15 percent.     

Enlargement of Claw Pole Motor Using SMC Cores Divided in the Circumferential Direction

Clawtooth motors have the feature that they can be made thin in the axial direction. This makes them suitable for appliances, automobile accessories, and small‐sized industrial motors. On the other hand, there is a need for thinner HEV and elevator motors and large‐sized industrial motors. In this study, we examined ways of increasing the output of clawtooth motors. We arrived at the following conclusions. (1) The optimal stator structure was determined and the prospects of attaining the target specification of 123 N‐m were determined. (2) Three important manufacturing tasks, assurance of core assembly accuracy, thin coil manufacture, and rotator insertion, were identified. (3) Experimental results and the results of analysis were in agreement with respect to the EMF. (4) The experimental cogging torque results and finite element analysis (FEA) results were in agreement with the FEA results at sixth order but not at second and fourth order. (5) Although the core needed to be divided in the circumferential direction in order to increase its size, it was clear that the influence on the torque was small. (6) Use of a divided core is a good solution for enlargement of clawtooth motors.     

Construction of a low parameter and disturbance sensitivity system by a model-following method

Many conventional design techniques can be only applied to ideal controlled objects without parameter variations and disturbances. This paper proposes a new method by which these techniques can be applied to practical objects with parameter variations and disturbances. The principle is to construct a model-following system which makes the practical object output follow the model output and to convert the practical object to the ideal object which has extremely low parameter and disturbance sensitivity.     

Analysis of ATP and Its Breakdown Products in Beef by Reversed-Phase HPLC

Analytical conditions for the quantitative determination of adenosine 5′-triphosphate(ATP), adenosine 5′-diphosphate(ADP), inosine 5′-monophosphate(IMP), adenosine 5′-monophosphate(AMP), hypoxanthine(Hyp), xanthine(Xan), inosine(Ino) and adenosine(Ado) in meat extracts by reversed-phase high-performance liquid chromatography (HPLC) were examined. A commercial ODS column with a 5-μm particle diameter was used, and expeimental parameters affecting the separation were discussed. Peaks in chromatograms of meat extracts were identified by retention time, co-injection with standards, absorbance ratios and the enzymatic peak shift method. The procedure proposed was adaptable as an indication of freshness of meat.     

Proteolysis Affects Thermal Gelation of Squid Mantle Muscle

Thermal gelation of squid mantle muscle was studied by means of gel strength measurement and SDS-polyacrylamide gel electrophoresis. The gel strength of thermally induced squid meat gel decreased when squid meat paste was heated in two steps (35°C for 30 min followed by 90°C for 30 min). This decrease in gel strength was effectively depressed by the addition of protease inhibitors such as ethylenediaminetetraacetic acid (EDTA), phenylmethylsulfonyl fluoride (PMSF), and soybean trypsin inhibitor, indicating that me-tallo- and/or serine-proteases were mainly involved in the deterioration of squid meat gel prepared by two-step heating. SDS-PAGE analysis demonstrated that EDTA or PMSF suppressed the degradation of myosin heavy chain.     

地铁站内烟气流动特性和消防安全

介绍了地铁站内烟气流动和控制的试验和数值研究。在三个真正地铁站内利用甲醇油池火作为燃料进行了试验，用所获得数据来验证地铁站火灾数值模型，并进一步检验其烟控系统的性能。在站内使用了制量烟气流动模型，再现了最简单条件下每个站点的试验结果，然后把结果跟其他试验条件下的试验结果进行了比较。最后，用模型预测更复杂火灾的烟气流动情况。另外，还讨论了地铁系统的有效设计和火灾安全设施的正常运作情况。通过限制内饰面材料的燃烧性能或者安装自动喷淋系统都可以有效控制热释放速率，且在站点两端开设逃生路线、站台和地铁隧道直接卷帘的正常启动等可有效保证安全疏散。     

Wavelet Multi-Resolution Cross-Correlation Analysis of Swirling Gas-Solid Flow in a Horizontal Pipe

A wavelet multi-resolution cross-correlation analysis was developed and applied to experimental pressure-time signals in order to analyze the characteristics of swirling gas-solid flow in both Fourier and physical spaces. The experiment was carried out in a horizontal pipe with a length of 7.5 m and an inner diameter of 76 mm. The initial swirl number based on the total inflow was varied from 0.0 to 0.61, the mean gas velocity was varied from 6 to 28 m/s, and the solid mass flow rate was varied from 0.08 to 0.5. From the wavelet multi-resolution correlation analysis of the fluctuating pressure in the range of low air velocity, the characteristics of swirling gas-solid two-phase flows were extracted at various frequencies. Much stronger correlations were found in the range of low frequency, which implied periodic motion of dunes and sliding clusters. Additionally, it was revealed that the motion of a large cluster sliding flow contains two smaller clusters and the moving velocities of dunes were 1 m/s and 2 m/s, respectively. However, no correlation existed at smaller scales of correlation features, which indicated heterogeneous suspension flow.     

Study on Improving Precision of Analysis of Boost Ratio and Power Efficiency of Tapped‐Inductor DC–DC Converter Circuit

Analysis precision of boost ratio and power efficiency in boost DC–DC converter circuit is improved by proposing adaptive equivalent circuit of output diode of the circuit. In experiment, boost ratio and power efficiency in high boost ratio circuit were 9.89% and 76.5% respectively with its load resistance of 20 Ω driven by output voltage 10 V. In experimental results, error in theoretical values of boost ratio compared with the measured values of that was reduced to ?3.79% from 57.5% in the conventional circuit. In a tapped‐inductor high boost ratio circuit, error in theoretical values of boost ratio was reduced to 3.54% from 31.8%. Error in theoretical values of power efficiency with the measured values of that was reduced to 5.51% from 33.2% in the conventional circuit. In a high boost ratio circuit, error in theoretical values of power efficiency was reduced to ?3.32% from 17.3%. Power loss of every element in boost DC–DC converter circuits was analyzed with high precision by analysis of inductance current waveforms in those circuits. Error in theoretical values of power loss compared with measured values was reduced to equal or less than 5%.     

Protein-Protein Interaction of Fish Myosin Fragments

Protein-protein interaction of myosin fragments from flying fish and white marlin muscles was studied by means of absorbance changes resulting from aggregation at temperatures of 20°C to 70°C. Subfragment-1 (S-1) exhibited a high extent of interaction with the transition temperature of 35–36°C, while the interaction of heavy meromyosin (HMM) was very weak. Though light meromyosin (LMM) gave lower interaction values throughout the heating temperature, the addition of butanol promoted markedly the interactions at the temperature above 50°C. The degree of promotion was high for flying fish and low for white marlin.