Improved direct bonding method of Nd:YVO4 and YVO4 laser crystals

We succeeded in the fabrication of bonded laser crystals composed of a neodymium-doped YVO₄ laser crystal (Nd:YVO₄) and its host crystals YVO₄ by a newly developed dry etching technique using an argon ion beam. The optical distortion caused by the bonded interface of size 5 mm × 6 mm was estimated to be 0.05λ at 633 nm. From the comparison of laser performance pumped by a laser diode, the bonded crystals could increase the laser output power by nearly twice that of the non-bonded crystals with the same degree of polarization of 99.2%. To analyze the mechanism of the enhanced reduction of the thermal load in the bonded crystals, numerical simulations with a finite-element method were also performed.     

Plastic deformation of bcc metal thin foils without dislocation

Heavy plastic deformation of fcc metal thin foils to fracture has been found recently to proceed without involving dislocations, and it results in the formation of high density of vacancy clusters. Thin foil specimens of bcc metals such as V and Mo were plastically deformed to fracture in in situ elongation experiments under an electron microscope. Morphology of thinning and fracture was found to be similar to fcc metals, and no dislocation was observed during heavy deformation. Electron diffraction analysis at the tip of a crack during deformation confirmed a large elastic deformation of up to 5%. Unlike in fcc metal thin foil specimens, point defect clusters were not observed near fractured tips. This difference is attributed to the difference in vacancy reaction, though the deformation in bcc metals without dislocation most likely does produce vacancies.     

Dislocation structures introduced by high-speed deformation in bcc metals

Systematic experiments were carried out over a wide range of strain rate, 10⁰–10⁶ s⁻¹, so as to reveal the deformation mode in bcc crystals, especially at high strain rate. Dislocation structure showed heterogeneous distribution at low strain rates in all three bcc metals examined. At higher strain rates exceeding 10³ s⁻¹, distribution of dislocations was random, and the formation of small dislocation loops was observed in V and Nb. In Mo, small dislocation loops were not formed by deformation, even at high strain rates. However, post-deformation annealing of an Mo specimen that had been deformed by 20% at 5×10⁵ s⁻¹ produced dislocation loops. The inside–outside contrast method identified these loops to be of vacancy type. These results reveal that in Mo vacancy clusters are not formed directly from the interaction of dislocations, but by the aggregation of vacancies. In V and Nb, the same formation process is believed to occur at high strain rates. These results suggest that the different mode of plastic deformation at high strain rates accompanied by production of vacancies also occurred in bcc metals.     

Control of polymerization processes of 10,12-pentacosadiynoic acid LB films

Studies have been carried out on KrF excimer laser light (EX), X-ray or electron beam (EB) induced polymerization of 10,12-pentacosadiynoic acid (PDA) Langmuir-Blodgett (LB) films in relation to molecular density or molecular arrangement of the films using X-ray diffraction analysis, infrared (IR) spectroscopy and Raman spectroscopy. The molecular arrangement or density of the PDA LB films was controlled by subphase conditions when the films were built up, such as pH, temperature of a subphase or salt concentration in the subphase. Polymerization sensitivity of the PDA LB film was affected by the arrangement or molecular density. On low density (A type) films the polymerization occurred by irradiation with EX, X-ray or EB, but on high density (B type) films the polymerization occurred only when the irradiation was carried out by high energy beams such as X-ray or EB. Decomposition of polymerized films was observed further by excessive irradiation of EX or X-ray, but not on the B type films. It was revealed by X-ray diffraction analysis that in the A type film, the PDA molecules bent to a larger extent than those in the B type film and the polymerization proceeded topochemically, that is, the thickness decreased little after EB irradiation in a helium atmosphere. On the other hand, in the B type film, the thickness decreased by about 10% as a result of EB irradiation. By IR reflection-absorption (RA) and Raman measurements, it was confirmed that conjugated diacetylenic bonds disappeared and conjugated double and new conjugated triple bonds appeared after high energy beam irradiations. These results support the supposition that 1,4-polymerization, i.e. polydiacetylene type polymerization, occurs easily in the A type film and 1,2- or 3,4-polymerization, i.e. polyacetylene type polymerization, occurs in the B type film, and that the polymerized A type film was decomposed at the polydiacetylenic bond when the irradiation continued further. It was also shown that the polyacetylene type polymer was obtained only when the B type film was irradiated with the high energy beam.     

Dynamics of Vortex Lattice Formation in a Rotating Bose-Einstein Condensate with an Optical Lattice Potential

We study dynamics of quantized vortex lattice formation in a rotating Bose-Einstein condensate with a square blue-detuned optical lattice by solving the Gross-Pitaevskii equation. This dynamics depends on the depth of the optical lattice. Vortices tend to form a triangular lattice under the rotation, while an optical lattice likes to pin vortices at their peaks. Such a competition of two effects makes this system more interesting and complicated.     

A reconfigurable VLSI-based double-lens tracking camera

Watching and tracking an object while seeing a much wider view is one of advantages of the eye system. We proposed and developed a tracking camera system that mimics the eyes by using double-lens modules. In the system, a wide view is captured through the wide-lens module, while the target in it is tracked and magnified through the telescopic lens module. Electronic circuits for tracking control are implemented onto the reconfigurable VLSI or FPGA in order to embed the parallelism in the tracking algorithm into the hardware. A successfully developed FPGA-based prototype performs high-speed tracking at the video-rate. This work was present in part at the 12th International Symposium on Artificial Life and Robotics, Oita, Japan, January 25–27, 2007     

Sintering of the Mechanochemically Activated Powders of Hexagonal Boron Nitride

Pressureless sintering of hexagonal boron nitride (BN) was performed using a powder activated by mechano-chemical treatments. Physical properties of the sintered BN bodies depend on the type of starting powder and the conditions of the treatments. The BN body, which was obtained at 2000°C using an appropriate activated powder, was 99 wt% pure and was excellent in mechanical and physical properties, in spite of its low density (1.64 g/cm³).     

Note: detection of micro-cracks in the interlayer dielectric film by the stress based light scattering method

A phenomenon was discovered wherein light scattering strength from cracks increases when tensile stress is applied to micro-cracks produced in the interlayer dielectric film by chemical mechanical polishing treatment. It is likely that the change in light scattering intensity occurs because a region of high stress concentration (region with high variation in index of refraction) is produced near the crack tip due to stress, thus forming a type of scatterer. With this method, it is possible to detect only scatterers which respond to stress, and thus, it is possible to classify and separately detect cracks and particles.     

Evolvable Reasoning Hardware: Its Prototyping and Performance Evaluation

In this paper, we propose evolvable reasoning hardware and its design methodology. In the proposed design methodology, case databases of each reasoning task are transformed into truth tables, which are evolved to extract rules behind the past cases through a genetic algorithm. Circuits for the evolvable reasoning hardware are synthesized from the evolved truth-tables. Parallelism in each task can be embedded directly in the circuits through the direct hardware implementation of the case databases. We developed the evolvable reasoning hardware prototype using Xilinx Virtex FPGA chips and applied it to the English-pronunciation-reasoning (EPR) task. The evolvable reasoning hardware for the EPR task was implemented with 270K gates, achieving an extremely high reasoning speed of less than 300 ns/phoneme. It also achieved a reasoning accuracy of 82.1% which is almost the same accuracy as NETTalk in neural networks and MBRTalk in parallel AI.     

Solving a Nonlinear Problem in Magneto-Rheological Fluids Using the Immersed Interface Method

Many applications lead to a nonlinear elliptic interface problem in which the discontinuous coefficient depends on the solution and the material properties. A finite difference method based on Cartesian grids and the maximum principle preserving immersed interface method is proposed for the nonlinear elliptic interface problems discussed in this paper. Numerical experiments against the exact solutions reveal that our method is nearly second order accurate in the infinity norm. The method is applied to study the magneto-rheological field-responsive fluids that contain iron particles. Numerical experiments are performed against the results from the literature.