Oxidation of doped europium in BaMgAl10O17 by annealing studied by x‐ray‐absorption fine‐structure measurements

Abstract— We studied the influence of annealing in air on doped europium in BaMgAl₁₀O₁₇ by performing x‐ray absorption fine‐structure measurements. We determined the oxidation of doped divalent europium by annealing in air at over 500°C. The interatomic distance between the europium and the surrounding oxygen atoms was compressed by oxidation. It also appears that the oxidation process of europium is determined by the diffusion of oxygen into BaMgAl₁₀O₁₇.     

Preparation and antibacterial activity of novel fluoroalkyl end-capped oligomers/silica nanocomposites-encapsulated low molecular biocides

Fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide oligomer [R_F-(DOBAA) _n -R_F] reacted with tetraethoxysilane (TEOS) and silica nanoparticles in the presence of low-molecular weight biocides such as hibitane, hinokitiol, and hinokioil under alkaline conditions to afford R_F-(DOBAA) _n -R_F/silica nanocomposites-encapsulated these biocides in excellent to moderate isolated yields. Fluoroalkyl end-capped N,N-dimethylacrylamide oligomer [R_F-(DMAA) _n -R_F] and acrylic acid oligomer [R_F-(ACA) _n -R_F]/silica nanocomposites-encapsulated hibitane were obtained under similar conditions. Dynamic light scattering measurements showed that the size of these fluorinated nanocomposites-encapsulated biocides thus obtained is nanometer size-controlled. Additionally, these fluorinated nanocomposites were shown to have a good dispersibility and stability in methanol and water. Of particular interest, these fluorinated nanocomposites-encapsulated biocides were found to have a good antibacterial activity against Staphylococcus aureus, and these nanocomposites were applied to the surface modification of traditional organic polymers such as poly(methyl methacrylate).     

A flow simulation for the epoxy casting process using a 3D finite‐element method

A three‐dimensional flow simulation for epoxy casting has been developed. A control‐volume‐based finite‐element method is employed, containing a conservative upwind formulation for the advection terms and equal order interpolations for all variables. This simulation predicts the non‐isothermal and reactive flow behavior under the gravity. The viscosity and reaction‐rate parameters were estimated by using a dynamic rheometer and a differential scanning calorimeter. The predicted flow front advancement and temperature profiles in the calculation domain similar to the mold cavity were in close agreement with the corresponding experimental results. The variation of epoxy surface configuration with flow rate also showed the same tendency between the prediction and the experiment. This simulation seems to be applicable not only to the epoxy casting, but also to other molding processes of various thermoset resins. POLYM. ENG. SCI. 45:364–374, 2005. © 2005 Society of Plastics Engineers.     

Two geometrical isomers of linoleic acid: Improved total syntheses

The total syntheses of 9(Z),12(E)- and 9(E),12(Z)-octadecadienoic acids have been carried out. A useful intermediate in both syntheses, 8-bromo-octanoic acid, recently has become available from commercial sources. This compound has been used to expedite the preparation of these isomers. The remaining carbon atoms were derived from propargyl alcohol along with either 1-heptyne or acetylene and 1-bromopentane. Because the overall yield for each sequence was roughly 15% and there were no extraordinary reaction conditions in any of the synthetic steps, the compounds could be prepared readily in multiple gram quantities. The syntheses of the two compounds were supported by data from a variety of spectroscopic techniques.     

Pressure anomaly in the paramagnetic region of bcc solid3He

The isochoric pressure of bcc Solid³He in the vicinity of the triple point has been measured by changing the temperature stepwisely and waiting for thermal equilibrium. We observed anomalous pressure kinks of the temperature dependence in the paramagnetic region near the triple point. This anomaly appeared at 0.37 to 0.40 tesla, and disappeared below 0.36 tesla. Moreover, critical phenomena at the transition point from the paramagnetic phase (PP) to the high field phase was observed and the phase line curves toward the PP side.     

Distribution of higher-order structures in injection-molded polypropylenes

Flexural test specimens were injection-molded from six homoisotactic polypropylenes with MFI = 0.49-25.1 dg/min under cylinder temperatures of 200-320°C. Distributions in the flow direction of higher-order structures such as crystallinity X_c, thickness of skin layer, a*-axis-oriented component fraction [A*], and crystalline orientation functions and distributions in the thickness direction of higher-order structures such as X_c, β-crystal contents, [A*], and crystalline orientation functions were studied. These higher-order structures are inhomogeneous in the flow and thickness directions, which strongly influences the product properties such as mechanical and thermal properties. Molecular orientation process in injection molding was theoretically analyzed from a viewpoint of growth of recoverable shear strain at the gate and its relaxation in the cavity, which could considerably well explain the variations in the flow and thickness directions of the quantities such as thickness of the skin layer and crystalline orientation functions which express the degree of molecular orientation.     

Characteristics of hydrogen-fueled gas turbine cycle with intercooler,hydrogen turbine and hydrogen heater

The performances of a hydrogen-fueled gas turbine cycle equipped with an intercooler, regenerator, hydrogen turbine and recuperative hydrogen heater are analyzed. The intercooler is very effective to prevent the condensation and freezing of water vapor in cooling the suction air. The operation of hydrogen turbine in low-temperature range can also be prevented by adopting hydrogen heater. Thermodynamic analysis has revealed that the thermal efficiency and the specific output are considerably improved compared to those of the simple gas turbine cycle.     

Continuous formation of slurry ice by cooling water–oil emulsion in a tube

Water-silicone oil emulsion with an additive, (C₂H₅O)₃SiC₃H₆NH₂, was examined as a heat storage material. A spiral tube used as a heat exchanger was immersed in a low temperature bath and the emulsion was circulated in the tube to make ice continuously. Ice was separated from the ice–liquid suspension in an outlet tank. The amount of formed ice, the temperatures of the inlet and the outlet of the heat exchanger, and the temperatures in the tube wall were measured and the overall heat transfer coefficient and the heat flux through the tube were calculated. Experiments were carried out, varying the flow rate, the temperature of cooling brine, and the thickness of tube wall. The condition under which slurry ice was formed continuously without adhesion of ice to the cooling wall was clarified. Though decrease in the thermal resistance of the tube increased the rate of ice formation or raised the brine temperature, it narrowed the range of the flow rate and of the brine temperature in which slurry ice was formed continuously.     

Synthesis and surface properties of novel fluoroalkyl end-capped amphiphilic fullerene cooligomers

New fluoroalkyl end-capped fullerene cooligomers were prepared by the reactions of fluoroalkanoyl peroxides with fullerene and comonomers such as acryloylmorpholine, N,N-dimethylacrylamide and acrylic acid. These fluorinated fullerene cooligomers were easily soluble in water and common organic solvents, and were able to reduce the surface tensions of both water and benzene, quite effectively. Additionally, these fullerene cooligomers were found to form a stable monomolecular film at the air-water interface, and the modified polystyrene surface treated with these cooligomers was shown to have a strong hydrophilicity with good oil repellency.     

Characterization of the cell leakage of a stacked trench capacitor(STT) cell

The cell leakage of a stacked trench capacitor (STT) cell has been investigated. The major leakage mechanisms of the STT are trench-to-trench leakage, trench junction leakage, and LOCOS isolation leakage. It is shown that compared to a conventional trench capacitor, the trench-to-trench leakage current is reduced and high punchthrough voltage is obtained. Therefore, the trench-to-trench spacing can be reduced 0.1 μm shorter than that of the trench capacitor. These reductions result from the STT structure itself. The surface leakage current, which is the dominant leakage current in the trench capacitor, does not flow in the STT. This paper also describes the effect of the sidewall damage caused by trench etching on the trench junction leakage. Reactive ion etching (RIE) produces deep levels just beneath the trench surface. But, the trench junction of the STT is not influenced by these deep levels because the trench surface is covered by a n^-diffused layer. This paper also investigates the relationship between the cell leakage and the retention time. At DRAM operation temperatures, LOCOS isolation leakage is dominant rather than trench junction leakage. Therefore, the deeper trench can increase the storage capacitance and improve the retention time