Time-dependent deformation in an enhanced SiC/SiC composite

Time-dependent deformation in an enhanced SiC/SiC composite has been studied under constant load at high temperatures of 1200 °C, 1300 °C, and 1400 °C. Creep damage evolution was evaluated by a Young’s-modulus change of partial unloading and microscopic observation. The addition of the glassy phase in the matrix is very effective for protecting the composite from oxidation. The transient creep is dominant in creep life at all the temperatures. An empirical equation is proposed to describe creep behavior of the composite. It is found that creep activation energy increases with creep time at stresses lower than matrix cracking stress, but the activation energy remains constant at stresses higher than the matrix cracking stress. The creep strain rate of the composite is considered to be controlled by creep of fibers based on examining the time, strain, stress, and temperature dependencies of creep strain rates.     

Radiation tolerance for the SMASH-series front-end chips for a silicon micro-strip detector

The radiation tolerance for prototype front-end chips designed for a silicon micro-strip detector was examined with a ⁶⁰Co irradiation source to establish an allowable range of the radiation dose. The irradiated front-end chips were SMA²SH-64A, a 64-channel preamplifier array; SMA²SH-1, a single-channel preamplifier circuit with a comparator; and Control-C, a digital-control chip for the preamplifiers.     

Effective thermal conductivity of compressed woods

Compression is one solution to improve the strength of softwoods. The effective thermal conductivities of compressed Japanese cedars (cryptomeria japonica), which were compressed in the radial direction of the wood, were measured. Both the effective thermal conductivities in the tangential and fiber directions increase proportionally to the density increment due to the compression. However, the thermal conductivity in the radial direction (compression direction) increases slightly with the density increment. Numerical computations were conducted to explain the characteristics of thermal conductivity in the radial direction by using a microscopic heat conduction model for the compressed wood. The numerical results were compared with the measured values. And the physical mechanism of the heat conduction in the compressed woods is discussed.     

Development of a single loop EPR test method and its relation to grain boundary microchemistry for alloy 600

A single loop electrochemical potentiokinetic reactivation test method has been developed for alloy 600 that produces good passivation on all the surfaces, good etching during the reactivation scan and no appreciable pitting. It is able to quantify and discriminate between samples with a wide range of degree of sensitization. The Pa value correlates well with the minimum level of chromium in the depletion regions at the grain boundaries. It has been shown that the width of the attacked regions is much larger than the width of chromium depletion regions and it does not show any direct correlation with either depth or width or with a volume parameter of chromium depletion regions. It has been shown that the chromium carbides are not attacked during the test and that the intragranular regions attacked during the test are the sites of chromium carbides in the grain matrix. A modified Pa parameter is shown to be sensitive down to 7.5 wt% chromium in the depletion regions and indicates that the intragranular carbides have shallower depletion profiles than those at grain boundaries. Comparison of the results of the single loop and the double loop tests showed a good correlation.     

Recovery retardation in equal channel angular pressed Al–Zr alloy during friction stir welding

The effect of Zr on reduction of hardness and microstructure in an FS weld of equal channel angular-pressed Al alloy was investigated. Zr addition to Al suppressed dynamic recovery in the thermomechanically affected zone and enabled retention of the high hardness of the ECA-pressed material throughout the weld.     

The heat transfer and pressure drop characteristics of finned tube banks in forced convection (effects of fin height on pressure drop characteristics)

In recent years the requirement for the reduction of energy consumption has been increasing to solve the problems of global warming and the shortage of petroleum resources. For example, in the power generation field, as thermal power generation occupied 60% of the power generation demand, considerable improvement of the thermal efficiency is required. This paper describes the pressure drop characteristics of finned tube banks used for heat exchangers in thermal power generation that were clarified by testing serrated finned tube banks with different fin heights for improved heat transfer and conventional spiral finned tube banks with different fin heights, and an equation to predict pressure drop which is necessary for the heat exchanger design is proposed. © 2006 Wiley Periodicals, Inc. Heat Trans Asian Res, 35(3): 179–193, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20112     

When West meets East: Contributions of Eastern traditions to the future of psychotherapy.

Discusses 2 interrelated traditions as they are reflected in contemporary and traditional approaches to psychotherapy in Japan. One uses various meditational and self-focusing instructional sets whose common goal is to facilitate the slowing down, deepening, and clearer focusing of sensory and interpersonal awareness. The 2nd tradition focuses on physical self-regulation and autonomic self-control through exercises that foster enhanced voluntary control over physical states and processes. Eastern psychology offers a set of practices that help the individual overcome the inherent selfishness of his/her isolated experience. The goals of such work include recognition of gratitude to important people in the client's life, rediscovery of the joy of meaningful work, and the experience of a unifying cosmic consciousness. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Strengths and ductility of Mo–TiC alloys after secondary recrystallization

A series of Mo–TiC alloys were heated in vacuum at 2473 K for 36 ks. First grain growth behavior was observed using a scanning electron microscope. Then effects of TiC addition on the strengths and ductility at low temperature were discussed from the viewpoints of chemical composition and grain structure.

Materials with TiC additions of not larger than 0.1% demonstrated a single-crystalline grain structure. Both yield and maximum strengths increased by TiC addition and consequently ductility was improved.     

Distributed architecture for energy management D-structure

Electric power systems are expanding in size and complexity, and the requirement for the energy management system (EMS) is becoming more important. In this computer control system, a single control computer is used mainly as the primary computer and its software is very complicated because of its hugh number of small, quick tasks to obtain high response speed. Therefore, much effort is needed to develop and modify the programs, and the responsiveness of this centralized architecture varies greatly when many faults occur in the power system. This paper describes a new distributed architecture for the EMS. Distributed processors execute the functions cooperatively with periodic access to the common bulletin board database in which information about the power system exist. This architecture facilitates the software development and maintenance, and it also enhances the performance by the parallel processing of the distributed functions.     

Towards a Solution to the North‐South Problem

One of the most important issues in avoiding a global water crisis is to solve the confrontation between developed and developing countries. As Japan in the 20th century has experienced the shift from a developing country to a developed country, it should candidly share its precious historical experience, both its merits and demerits, with people throughout Monsoon Asia. Two practical proposals to economize water demand are as follows: to economize toilet water in a way that meets the conditions of each region; and to develop the effective utilization of water for irrigated rice paddies, not only in the Monsoon Asia but throughout the world. In short, new life-styles are necessary if the global water crisis is to be averted.